After purchasing a long-awaited washing machine, many users begin to complain about excessive noise and vibration during operation. For this reason, anti-vibration stands for washing machines are used. How justified this is and how to choose the right gaskets, read below.
Causes of vibration and their elimination
The cause of the vibration that occurs should most likely be looked for not inside the car, but outside. And the technology itself may have absolutely nothing to do with it. But an uneven floor and differences in the upper tile layer can be the main consequence of vibration noise. It is the instability of the installed equipment that is most often the main cause of the appearance of a noise irritant.
Engineers are constantly developing special devices and mechanisms designed to combat both vibration itself and its negative consequences.
Regardless of the factor that turns out to be the reason why the washing machine creates strong vibration during operation, it is necessary to correct this problem. This must be done, because frequent fluctuations can lead to further serious problems. The drive belt and tank may break. Other parts can quickly become unusable.
The presence of moving parts in the washing machine leads to the formation of this negative phenomenon.
What needs to be done? Of course, first of all, check that the machine is installed evenly. Perhaps it is positioned incorrectly, but the floor itself is fine. It is possible that its legs were simply not adjusted during initial installation. If, after fastening, no sounds occur when you turn it on, then the problem is solved.
The legs of not all washing units are equipped with rubber or polymer noise- and vibration-absorbing pads.
However, as has already been stated, in most cases the reason lies in the unevenness of the floor. This means some minor repairs are needed.
In this case, manufacturers suggest installing anti-vibration pads under the legs of the washing machine.
Important! Provided that the difference in the floor is small, for leveling it is not necessary to dismantle the entire tile and level the entire floor area. You can select a separate area where the washing machine is located and work specifically only with it. This will save a lot of time and money, which is also important.
If your washing machine vibrates excessively during the spin cycle, you're not alone.
The surface is checked by level. A leveling screed is made and after drying an even layer of tiles is laid. Accordingly, the tiled surface is also checked by level.
Why does vibration occur when washing?
Before purchasing foot pads, you need to make sure that the washing machine was installed correctly. Turn off the machine and shake your hand. If the body is wobbly, it means that not all the legs are touching the surface evenly.
To set the legs to the same height, turn the nut in different directions.
For an accurate check, use a level. Even when tilted slightly, the machine may make noise and move during the spin cycle.
Causes of strong vibration:
- After transportation, the transportation bolts were not removed . Then you need to get them out. They are located on the rear panel and help secure the internal parts of the SMA during transportation.
- Uneven or wooden floor . The plank floor sags over time, causing the machine to bounce during operation. You need to level the floor or install a rigid stand.
- Long-term use may cause bearing wear . Then the washing machine not only vibrates, but also makes a “terrible” hum and grinding noise.
Narrow cars vibrate most often. Their body is less stable, which leads to vibrations during spinning. In this case, the use of anti-vibration supports is justified.
When should it be installed?
Now let's move on to consider additional elements that help get rid of vibration sound. These are anti-vibration stands and mats.
These types of stands are an inexpensive and effective solution to the problem.
A set of vibration absorbing pads does an excellent job of holding the machine in place and reducing vibration loads.
Dimensions
The dimensions of the models vary depending on the parameters of the washing machines themselves. Based on this, there are products on sale with dimensions of 40x60, 50x60, 60x60 cm. The thickness of the product can be 25 mm. Products also differ in the size of the granules of the material used. They are smaller on top than on the inside and below.
In addition, there are options on sale with dimensions of 62x65 cm. The average thickness of the products can be 1.5 cm, weight varies from 2.5 to 4 kg. However, at the request of the customer, manufacturers can make a non-standard size mat. To do this, you need to measure the parameters of the occupied space for placing the washing machine.
Types of anti-vibration devices
On the market, the range of anti-vibration devices for washing machines is presented in two options: stands and mats of various models. They are made from different materials and although they perform the same function, the quality of their work differs.
The stands will protect the floor surface from scratches and characteristic marks.
The modern market of accessories for washing machines offers anti-vibration stands made of various types of plastics, silicone or special rubber.
Let's consider the first type of anti-vibration device. These are rubber stands. They are made from ordinary rubber or silicone. They play the role of additional legs installed under the equipment.
They greatly reduce the level of vibrations in the unit during the spin process.
They provide slight shock absorption and thereby reduce vibration.
Stands have their own variety. These are paws. They look very original and attract with their appearance. Those who want to purchase them will have to pay a little extra, since they are more expensive, but for the sake of attractiveness in the interior, many do not pay attention to this.
Washing machine feet are the same rubber supports, but they have an unusual appearance.
These products are made in the form of paws, for which you will have to pay a little more.
Now let's look at the second option, that is, anti-vibration mats. They are divided into two main types.
- Rubber mats.
- Silicone.
- When using a simple rubber covering (mat), the floor will be protected from damage, but vibration will not disappear. It will only go down a little.
- The use of special anti-vibration mats, which are thicker and have a different structure, will create conditions for complete absorption of vibrations.
For those who are concerned about the intense vibrations of the washing machine during washing and spinning clothes, there are special rubber mats.
Many, given the fact that the vibration is barely audible, nevertheless, still creates discomfort, believe that it is not necessary to look for an expensive corresponding product. It is enough to purchase a simple inexpensive rubber mat, which will also successfully cope with the task of eliminating noise.
They creep under the washing machine, lightly cushion and thereby reduce the force of vibrations.
In this regard, it is worth considering the following:
They can only be laid if the equipment is installed level.
How to choose stands
However, if you use a washing machine pad that is under warranty, problems may arise. Therefore, you should clarify whether this will affect the possibility of warranty service.
It is worth noting that the anti-vibration feet can be chosen in shapes, colors and materials that suit your taste; these parameters do not affect operation.
Branded models from well-known manufacturers will cost more and at the same time have the same characteristics as cheaper anti-vibration pads for a washing machine.
So what should you choose, mats or stands with special anti-vibration properties? Here you should take into account that when buying rugs, you need to clearly measure the size and distance between the legs.
The machine should rest solely on the rubber pads of the mat, its legs should not hang down.
Stands used for washing machines are more universal. The elasticity of the material allows them to be worn on the legs of most models. And, of course, the price of anti-vibration feet for a washing machine is less than the price of mats.
Structure and principle of operation of a special mat
A mat made for washing or other equipment that creates vibration is endowed with the main functions, which are to smooth out existing differences in the floor (if leveling has not been carried out) and eliminate vibration of the machine. A special relief layer on the back of the product helps to perform these functions.
In this case, we are talking about a special anti-vibration mat.
Video: Anti-vibration mat for car
This video material will help the consumer understand the variety of types of anti-vibration mats. The purposes of their use are the same, as are the operating principles, so you need to choose based on your own requirements.
The use of stands is a good solution to eliminate the annoying noise that occurs during the washing process. But, pads don't work if there are other problems. First you need to make sure that the washing unit is positioned correctly, on a flat surface. If this condition is not met, the use of a substrate will not eliminate hum and vibration.
List of sources
- techmentor.ru
- stroy-podskazka.ru
- mebel-expert.info
- mashmaster.ru
- luxury-house.org
- kitchenremont.ru
- dekoriko.ru
- 2stiralki.ru
- ubirai.ru
- DekorMyHome.ru
- 1stiralnaya.ru
Advantages of an anti-vibration mat
A rubber anti-vibration mat on which a washing machine or other unit that creates vibration is installed has a number of advantages:
The mat is affordable and there is nothing difficult to install.
The best anti-vibration mats are made from several layers of polymer or rubber.
How to install correctly
In order for the equipment to work quietly after installing the substrate, you need to know how to do it correctly. First, you need to make sure that it is level. If the machine wobbles, it must be leveled before installing the anti-vibration feet.
Then, lifting the automatic machine on each side, install rubber feet for the washing machine. Installing mats to stabilize your washing machine will likely require assistance.
You won’t be able to lift that much weight on your own, and the mat simply won’t slide on the floor.
But the crooked floor in the apartment will not allow you to level the equipment, in which case an anti-vibration stand for the washing machine will be the only solution.
