Repair of Indesit washing machines (Indesit) in Moscow at home

Repair of large household appliances / Repair of washing machines at home / Repair of Indesit washing machines

Repairing Indesit washing machines at home allows you to quickly eliminate malfunctions that arise in the operation of household appliances. Any, even the most reliable equipment periodically fails, this can be a consequence of a number of reasons:

Failure to comply with equipment operating conditions;
Power surges;
Increased hardness of tap water;
Natural wear and tear of equipment.

Prices for repairing Indesit washing machines

Name of service	Price, rub.)
Visit of the master	0
Diagnostics in case of repair	0
Replacing the hatch opening handle	400
Replacing the sealing cuff of the hatch	400
Replacing the hatch lock	400
Replacing the drive belt	300
Replacing drum bearings	2500
Replacing shock absorbers	800
Control module repair	1000
Replacing a group of filling valves	500
Replacing the sump pump	600
Replacing the heating element	600
Replacing motor brushes	500
Electric motor repair	500
Installing a new	1000
Cleaning the fill system	600
Cleaning the drain system	700
Removing a Foreign Object	600
Replacing the inlet and drain hose	400
A technician will visit you for in-depth diagnostics without repairs.	1500
In case of refusal, departure is paid in the amount	500

Call a specialist
8. Call!

* The minimum possible repair price is indicated, depending on the model and other factors. Please check the exact cost.

The machine does not respond to the on/off button

Despite their convenience, there are malfunctions that Indesit washing machines and their error codes cannot cope with.

If the power key fails, this does not mean that the entire control module is faulty.

The Indesit washing machine and its error codes, indicating problems with the control unit, do not indicate a problem with this button. To repair it, you need to dismantle the cover under which the electronic unit is located and remove it.

If there is external damage, the power switch must be replaced. Then, using a multimeter, you need to ring two wires, zero and phase. To understand whether current is flowing or not, the key must be turned on.

Advice: you should trust the Indesit wisl 62 indicators. The displayed error codes (F18) may indicate problems with current in the electronic unit. But there are times when repairing the power switch does not solve the problem and after turning on the program the button stops working.

If the key does not function during operation, the program may have crashed. In this case, you need to unplug the power cord and reconnect it after 10 minutes. As you can see, repairing the Indesit power button is easy.

Error codes for Indesit washing machines

F01.
F02.
F03.
F04.
F05.
F06.
F07.
F08. F10.
F09.
F11.
F12.
F13.
F14. F15.
F17.
F18.
No display.

F01. Closing the semistor circuit. Repair:

Checking and repairing wiring.
Replacing the controller or motor.

F02. Motor or tachogenerator malfunction. Solutions:

Replacing the bearings of an Indesit washing machine.
Wiring repair.
Replacing the control module.
Motor replacement or repair.

F03. Temperature sensor (thermostat) error.

Replacing the thermostat.
Replacement or repair of the control board.

F04. Water level sensor malfunction. Repair options:

Wiring repair.
Replacing the water level sensor.
Electronic controller repair.

F05. The Indesit washing machine does not drain water. Repair options:

Replacing the water level sensor.
Repair/replacement of the drain pump.
Cleaning systems, replacing hoses and filters.
Replacing the control module.

F06. The buttons don't work. Possible solutions:

Repair of electrical connection circuit.
Replacing buttons (display).
Replacing the control board.

F07. The heating element is not immersed in water. Solutions:

Replacing the heating element.
Replacing the water level sensor.
System cleaning.

F08. F10. Incorrect water level.

Replacing the water level sensor.
Replacing the heating element.
Replacing the control module.

F09. Module memory error.

Replacement of electronic control board, firmware.

F11. Drain pump malfunction. Repair options:

Replacing the water level sensor.
Pump replacement.
Replacing the control module.

F12. There is no connection between the drain and display modules.

Electrical circuit repair.
Replacing one of the modules.

F13. Malfunction of the drying sensor of the Indesit washing machine. Options:

Wiring repair.
Replacing the sensor.
Replacement of the entire module.

F14. F15. Doesn't heat water. The dryer does not turn on.

Replacing the heating element.
Replacing the temperature sensor (thermostat).

F17. The hatch door does not close. Indesit washing machine repair options:

Replacement of UBL (hatch blocking device).
Replacing the control module.

F18. Processor failure.

Replacing the electronic unit.

No display. After a period of time, count the number of signals, it will be equal to the error code.

Repair of Indesit washing machine in Moscow

Washing machine repair in our service center is a proven and reliable way to get maximum results in the shortest possible time. We:

We fix problems of any complexity. If your washing machine is acting up and not working correctly, call our specialists to your home. We will come, diagnose any problem, and quickly fix it.
We guarantee high quality work. Documentary evidence is provided.
We repair any model and brand of Indesit washing machine.
We offer a flexible pricing policy.

Simple malfunctions and methods for eliminating them

Very simple cause-and-effect chains are given in the documentation for the washing machine. Let's focus on those that are not often repeated, but can be easily eliminated with your own hands:

The wash does not start or the water does not heat up. The heating element needs to be replaced. It is easy to do and the part is available for retail sale.
There is no water drainage, the automatic system stops washing. The first thing to check is that the filter for accumulating large residues is clogged. Secondly, clean the outlet hose and check the drainage system. Electronics, as mentioned above, reacts very sharply to the parameters of fluid movement. Usually, after such repairs, the user remembers that it is necessary to do periodic maintenance of the machine.
Some Indesit washing machines suffer from the accumulation of fumes on the power filter coils. This malfunction can be easily eliminated: the elements are cleaned with a dry cloth and a long-hair brush.
Water or condensation entering the control unit stops operation. To continue, you should dry the machine or disassemble and wipe the electronic board. In any case, the presence of water most often does not lead to disastrous results; this is considered almost a standard regime.
Problems with the lid lock and control knobs can be resolved by cleaning and are classified as mechanical. They arise due to clogging and accumulation of soap deposits.
Over time, the drum shock absorbers in washing machines wear out. The level of noise and vibration during spinning increases. These elements are easily replaced independently.

In general, Indesit machines are reliable and unpretentious. If you carefully read the instructions, correctly connect them to the electrical network and sewage system, and ensure the recommended operating parameters, the devices will serve for a long time, delighting with reliability and efficiency.

Washing powder remains in the tray

Indesit washing machines sometimes have a problem with washing powder that is not completely washed out of the tray. As a result, the powder hardens and is difficult to remove. The most common cause is excess detergent. In this case, it is recommended to select and remember the most optimal dose. If the problem is not solved, then the reason may be poor-quality washing powder.

The next reason for powder residue is due to low water pressure, which is not sufficient to completely flush the powder out of the tray. The problem can be solved by cleaning the filter at the point where the washing machine connects to the inlet hose. Another way would be to increase the pressure in the water supply tap.

Sometimes the valve holes that supply water to the tray become clogged. To clean, you need to pull out the tray, find the valve, made in the form of a key, and clean it. At the same time, you need to clean the cuvette from dirt and powder residues. This procedure is recommended to be performed periodically for preventive purposes.

These are the most common causes that can be eliminated on their own. More complex situations may require the assistance of a qualified professional. More complex causes include a faulty water inlet valve. In this case, the powder is not removed from the tray at all. The usual solution to this problem is to replace the valve. The same applies to the solenoid valve that supplies water to the detergent dispenser.

Features of the electronic part

There are many complaints about the control unit of Indesit washing machines. There are even more instructions online describing faults and repairs of electronic parts. The main feature of the brand’s control units (by the way, they are quite standardized and the same systems are used everywhere, for example, on the WITL 86 and older models) is the need to carefully read the instructions and provide the machine with the necessary power supply modes. The distinctive features of the control electronics are as follows:

high sensitivity to sudden voltage changes;
automatic protection systems that are triggered by any discrepancy between parameters;
sensitivity to high air humidity or water ingress.

Electronic control module of the Indesit washing machine

But to the company’s credit, the control units are extremely reliable. The automatic protection stops the operation of the machine. However, restarting is simple: you need to eliminate the mismatch of parameters or simply select the desired program again. Washing will continue without problems, while most models support starting from the middle of the cycle.

There are also many complaints about the reactions of washing machines to the parameters of the inlet water and its drainage system. For example, vertically oriented models require that the liquid discharge point be exceeded by 60-80 cm relative to the sewer drain. For this purpose, the housings even have a hose mount. To ensure this mode, you need to read the instructions. But there are many cases where the machine literally explodes with foam when trying to remove water and floods the internal electrical system.

Troubleshooting algorithm

To accurately identify the cause of the failure, technicians recommend proceeding in the following order:

If you are dealing with a model equipped with a display, wait until the error code appears on it. The machine displays this information based on the results of self-diagnosis. What this or that code means is written in the instructions. For example, the message “F07” indicates problems with the heating element.
If the self-diagnosis function is not provided in the machine or it has malfunctioned, it is necessary to subject the device to an external inspection, and also check whether it begins to make any unusual sounds during operation. For example, the machine will let you know about the need to replace a bearing with a characteristic hum or knocking sound, especially clearly audible when operating in spin mode. You can guess about problems with the heating element by a cold hatch, as well as by the poor quality of washing and the presence of undissolved powder. If smoke comes out of the machine, the problem is clearly serious. In this case, it is better to hold off on doing it yourself - call a specialist.
If the breakdown has not yet been identified, the unit must be disassembled. Of course, this should only be done if the warranty period has already expired. You should start by dismantling and inspecting the surge protector. It is easy to find - it is the electrical wire that is connected to it. To remove the filter, you need to remove the cover from it and unscrew the screw holding it. If the tester shows a lack of power at its contacts, the cause of the failure can be considered detected.

If the surge protector turns out to be in order, you must again use a tester to check the power in all elements of the electrical circuit, and carefully inspect the mechanical components and parts. At this stage, even the most complex breakdown is usually identified.

In order not to forget what is screwed where, the assembly can be photographed before disassembly. It will also not be superfluous to study the structure of the unit and the location of fasteners before starting work.