How to open the door of an LG washing machine if it does not open after washing: what needs to be done to safely open the hatch of an LG washing machine?

Your LG washing machine finished the program, but when you tried to remove the laundry, you discovered that the door was blocked. It is impossible to get things. Why the washing machine does not open after washing, and how to remove laundry from it, we will tell you in this article.

Note! If you see that there is water left in the tank of the machine, then the reason why LG does not open the door is due to the drain. In this case, read our material “Why the LG washing machine does not drain water”

What is the washing machine door lock used for?

The mechanism that locks the drum door of the washing machine is designed to ensure safety during washing.
The mechanism locks the hatch automatically when the machine starts and opens it later after its operation is completed. If the door locking mechanism malfunctions, it remains closed even after the wash is finished and the machine is turned off. The main reasons leading to this malfunction are:

Software errors arising from power surges or problems associated with pumping and draining water;
Wear of the mechanism that locks the hatch;
A clogged hose preventing complete drainage of water;
The child lock system is activated.

If the cause of the problem is a power supply failure, you must wait until the specified program is reset. As a rule, it resets within half an hour, after which the hatch can be safely opened. True, this method of “repair” will not work if there is still water in it.

If the child lock function is turned on unplanned, the drum door can only be opened by simultaneously pressing two unlocking buttons on the machine. Moreover, each brand of washing machine has a different combination of buttons that can open the locking mechanism.

If, at the end of the wash, not all the water has been pumped out of the machine and the door does not open because of this, you can use one of the following options to solve this problem:

repeat the laundry spin cycle again or run this function together with the rinse mode;
inspect the water drainage hose for blockages, and then run the spin mode again;
use an emergency opening cable, usually located next to the filter, in the lower right corner and colored red or orange. When using the cable, do not yank it - just, slowly, gently pull its handle.

If all of the above recommendations do not help, you can take a risk and try to remove the blocking manually. Once you decide to take this step, perform all actions as carefully as possible so as not to aggravate the breakdown. First, unplug the unit from the outlet and remove the top cover. Then, carefully disengage the mechanism that locks the door and tilt the machine. When tilted, its drum will move back and provide access to the lock location. Now, all that remains to be done is to reach it with your hand and open it. This unlocking method is quite complicated due to the considerable weight of the washing machine, so if you decide to do it, take someone to help you.

In 95% of cases, one of the considered methods of releasing laundry sent for washing will definitely help and the blocking of the hatch will be removed. The remaining 5% falls on the design nuances of equipment from various manufacturers and larger-scale breakdowns that only a professional can handle.

We looked at universal methods for eliminating the failure of automatic opening of the hatch of an automatic car, which can be applied to any model and brand. However, along with them, it would also be appropriate to touch upon methods applicable to models of a particular manufacturer.

Manual, forced opening of the washing machine door

In any case, if the door of a Bosch washing machine does not open, in order to detect a malfunction, test it and subsequently repair or replace the defective part, you must first open the door in order to gain free access to the mechanisms of the unit.

This is not at all difficult to do after carefully studying the provisions of the manufacturer’s instructions regarding the repair of this model of washing machine. If instructions are missing, you should use the following rules, common to all modifications of such household appliances:

Turn off the power supply to the device.
Open the drain filter door. It is located at the bottom of the machine on its front part.
In the picture that opens to you, find the cable (orange) intended for emergency opening of the drum receiving hatch. After locating the cable, gently pull it, thereby unlocking the door.

Prevention Tips

There are few specific recommendations for prevention and they relate to the general operation of the automatic washing machine.

First of all, handle any household appliances with care. When closing and opening the hatch of the washing machine, do not apply more force than is required. And don't do this unless absolutely necessary.
Secondly. Do not load the maximum amount of laundry into the tank. Especially if it prevents the door from closing.
Third. Respond promptly even to apparent operational problems. A minor malfunction that is not corrected in a timely manner can lead to larger and more serious breakdowns, up to and including complete failure of the entire washing machine.

If you are not confident in your ability to repair the device yourself, use the services of a specialist, which will definitely save you nerves, money and time.

Why might the lock get locked?

A washing machine is a technically complex device. The door lock may become blocked for reasons that you might not even think about at first. Using more force when opening is not the best option. You can simply break the lock. To solve problems at the root, you need to understand the probable causes.

At the moment, some program in which the door should be locked has not worked.
The hatch locking device is broken or jammed. The lock may break mechanically or be blocked by the control unit.

Water does not drain from the tank

If the washer door is blocked, the first thing to check before taking action to solve the main problem is whether there is water in the tank. If there is water, it is worth checking the installed program. Accidentally or by mistake, the machine may operate in a mode ending in “water stop”. In this case, it is enough to set the “drain water” mode. It is possible that the lock will unlock automatically after this program. You can also try to do this if the causes of the problem are not clear.

Water in the washing machine

Water in the drum may indicate serious problems.

The control unit has failed and the automatic drain does not work. Here you need the help of a professional.
The water level sensor or pump is broken. You should also contact service.
Perhaps the water does not go away because there is nowhere to go. If the sewer itself is clogged, you will need the help of a plumber (you can solve the problems yourself).

In these situations, the machine “sees” the water in the tank and blocks the lock for safety reasons so that it does not spill out onto the floor when the door is opened. Once the drum is empty, the door opens on its own.

Software locking

The door may not open because some program has not yet completed its operation. For example, some models do not have a sound signal when the cycle ends. Others have a long delay between washing and opening the door. More advanced washing machines also have protection at high temperatures. At the end of the process, the inner surface of the drum is hot. Until it cools down, the lock will be locked.

Power outages

The machine may not open for a very prosaic reason: at the right moment it was de-energized. It is worth checking if there is electricity in the house. If so, is the plug inserted into the socket and is it working? It also happens that if the machine does not open due to a power surge, it must be opened using software.

Defect of the UBL itself

Perhaps the lock itself is broken. A mechanical failure or even a minor defect can cause the hatch door to not open. You can replace the lock latch yourself.

The broken lock needs to be removed. To gain access to the mechanism, you need to remove the rubber cuff. Then unscrew the door.
Pull the lock out of the case, having previously photographed how it was attached to the sensors.
Install a new lock, focusing on the sensor connection diagram.

If everything is done correctly, the machine will open the door automatically after the end of the work program and the end of the delay time.

Replacing UBL

Broken door handle

Like any other mechanism subject to force, the door handle can fail. Most often this occurs due to excessive force when opening. The handle may break completely or become detached from the operating mechanism. Replacing the handle is a simple operation that you can do yourself. To do this, you need to remove the machine door to gain access to the lock. Make sure that the lock is in order, look at the connection diagram with the handle. Install a new handle or restore broken connections of the old one.

Problems with the control unit or sensors

If problems arise with electronics, then only a service worker can help. You can only test it yourself or try to solve the problem programmatically.

If the control unit or signal sensors are simply frozen, the machine must be disconnected from electricity. Leave it like this for 30 minutes or more, then turn it back on. If the internal computer returns to normal, the door will automatically unlock. If the technique does not work, other measures are needed.

Sometimes this technique helps: if the machine does not open after finishing the wash, run some other program or the same program again. The machine will automatically try to close the door before starting the program. Maybe she'll open it first. You can try to catch this moment (the click of the unlocking mechanism will be heard) and open it by the handle. This radical method is recommended to be used as a last resort. Or you can wait for the machine to finish working and hope that this time it will open.

How to unlock a Samsung washing machine

If, upon completion of its operation, the locking mechanism is not removed automatically, it is necessary to perform an emergency reboot of the software by disconnecting the unit from the power supply for at least half an hour. During this time, the selected washing program will be completely reset and the door will open.

If there is still water in the drum, selecting the spin mode again will help unlock it.

If the automatic pumping mechanism fails, you will have to drain it manually or using an emergency drain hose. As soon as the water is completely drained, the hatch will unlock automatically.

Another way to manually open the door is to use an element installed next to the emergency cable.

In general, it’s better not to risk repairing a Samsung machine yourself. If a malfunction occurs, you should immediately take it to a professional for diagnosis and repair.

Forced opening using a cord

A thin synthetic cord can help open the machine hatch if previous actions have not brought positive results. The disadvantage of this method, invented by folk craftsmen, is that it is not always suitable. The reason is the design of the lock. If the tongue snaps towards the body of the machine, it will open, but if it snaps away from the body or upwards, this method will not yield anything.

We recommend: Why does the washing machine vibrate strongly during the spin cycle and how to deal with it?

Step-by-step instruction

Prepare a piece of thin and strong cord or fishing line the size of the hatch circumference with a small margin.
Position yourself on the side opposite the castle.
Insert the cord into the gap between the body and the hatch around the entire circumference, and hold both ends in your hands.
Pull the cord until it presses against the latch.

If as a result of this the door does not open, then the lock design is of a different type and there is only one option left - remove the top panel.

Torx key

How to unlock an LG washing machine

The Lg brand washing machine has a child lock feature. If this function was accidentally turned on, the hatch simply will not open and will be locked until a certain combination of buttons is pressed on the machine. These buttons include Super Rinse and Pre Rinse. Press them on the unit at the same time, and then set your own settings using “Start/Pause”.

When you purchase an LG machine, be sure to save its instructions. It contains a section with recommendations for quickly unblocking, which will be very useful to you in this situation. Guided by detailed recommendations for action, you can quickly return the machine to its functionality.

Causes of door blocking and their elimination

Whatever the root cause of the blockage, remember that it is strictly forbidden to try to forcefully unlock the hatch. This risks causing you to get an electric shock, or the washing machine will require expensive repairs or a complete replacement. Let's look at the main reasons.

Reason #1 - auto-lock at the end of the wash

Automatic locking is necessary in order to avoid injury to humans and equipment breakdowns. When the cycle is completed, the hatch will automatically open.

But often the user is faced with the situation that after the drum stops, it is not possible to get things out - the door does not budge. This is not a breakdown at all, it’s just that the hatch does not open immediately after the end of the wash cycle. In such a situation, you should wait 1-3 minutes, the duration depends on the model of the washing machine.

Temporary interlocking is a precautionary measure designed to stop and cool the machine drum and the interlocking device itself.

If such a situation arises, do not even try to tug and pull the door - this way you will not solve the problem, but will only break the hatch. You should wait for the characteristic click or melody, after which the door will open itself.

Reason #2 - software failure

A failure in the washing machine program is, unfortunately, not uncommon. This happens for a number of reasons: due to voltage surges, frequent power outages, lack of water. Let's take a closer look at the procedure depending on the factor that led to the blocking.

Reason #1. Lack of light. The unit should be switched off immediately. Wait until the electrics are turned on, connect the device to the network and start spinning and rinsing, then the machine will turn off in operating mode when the cycle is completed.

If there is no light for a long time, then it makes sense to drain the water yourself through the hose on the back panel of the machine, after first turning off the power. In this case, the door will open on its own.

Before draining any water trapped in the drum through the hose, place a soft cloth or towel under the bottom of the washing machine.

Reason #2. Board failure. You should turn off the machine by holding the ON/ON button, and then unplug the cord from the outlet.

You can connect the device to the network after 30 minutes, during which time the machine will have time to reboot.

If the power goes out during the washing process, you should unplug the machine and drain the water yourself. After this, take out the laundry and wipe the drum

Reason #3. The water was turned off. You should turn off the power to the device, wait until the water appears and then connect the washing machine again.

Reason #3 - problems with the lock

Most washing machine models have an option that allows you to protect the equipment from attacks by a growing heir. This could be the reason why the door is blocked.

The Child Lock function is activated. To disable this program, you can refer to the instructions - it describes the algorithm for turning on/off this mode specifically for your machine model. Or just hold the “Start” button for 5-10 seconds and the hatch will unlock automatically.

The Child Lock feature will protect your baby from injury. To disable it, refer to the instructions, which outline the algorithm for pressing the buttons

The lock is broken. The fact is that all cars without exception are equipped with a physical mechanism that locks the door. And it may break. If the error code indicates that the problem is a faulty lock and there is no water in the tank, then you should force the door to open.

This can be done in two ways:

Unplug the washing machine. Take a cable or very thick thread. Carefully pull it between the door and the body of the machine. After these actions, pressure will be applied to the lock tongue, it will be released from the blocker, and the door will smoothly open. After turning off the power to the device, remove the top cover. Find the lock (use a flashlight), and to make it easier to get to the door, tilt the washer slightly towards you

Then press the hook gently with your finger or a screwdriver. After a click, the hatch will open.

Causes

The first thing you should not do if the washing machine does not open after washing is to use physical force. In this case, the hatch will be damaged, and the door is unlikely to yield to efforts. Before contacting a technician, you should exclude obvious factors that influence why the hatch is jammed.

Water in tank

The main purpose of the locking mechanism is to protect against water pouring out of the washing machine drum. That is why the hatch is securely closed at all stages of washing. If the drainage system does not work well, water will remain in the tank. In this case, it is necessary to lure the pump (pump), this problem may arise due to a blockage or an initial defect. Pump wear is affected by water hardness, powder quality and washing frequency.

Sometimes water may not drain due to a breakdown of the pressure switch - the water level sensor. The machine believes that the tank is empty, the drain does not occur - the door remains locked. New washing machine models have a separate “water drain” function. This problem is especially common in Samsung models.

Timed out

The machine immediately signals the end of the wash, but the door may remain closed for some time. A few minutes after washing are allotted to complete all processes correctly. After 2-3 minutes, the door will unlock automatically. Of course, on some models the hatch opens immediately after the signal, but it won’t hurt to wait at least 30-40 seconds.

If you urgently need to stop work, but there is no need to remove or put in laundry, you can simply click on “Pause”. This will pause the operation; you will not have to open the door with physical force. Then, by clicking on the same button, you can resume the process.

Lack of light

An annoying situation familiar to many: there were only a few minutes left before the wash was completed when the electricity went out. It will not be possible to open the washing machine door until it is resumed - the locking mechanism is broken. If the light is expected soon, it is better to just wait.

In case of long-term power loss, you should not leave laundry in the machine drum. However, you cannot pull it out simply by pulling a special cable. In this case, water from the drum will pour onto the floor, and the threat of flooding the neighbors will become quite real. Before taking out the laundry, you need to drain the water: unscrew the lower facade, pour the water into the basins through the filter. The volume of liquid can be 10-15 liters, this must be taken into account. After the drum is completely empty, the door may open in response to the draining of water. Otherwise, you will have to follow the instructions for the machine.

Stopping the program

If the washing machine door does not open, even though the operating time has expired, and the timer shows the opposite, you need to understand the reasons. The program could stop as a result of the following problems:

water does not enter the tank;
the liquid did not drain out after washing;
heating element failure;
accidental pressing of buttons after starting the wash.

If none of the reasons are true, you will have to call a repairman. You should not disassemble the machine yourself - the “brains” of the device can easily be damaged.

Broken lock latch

If there were no electrical failures or failures in the washing program, the lock latch may be the cause. If clothing gets into the lock device, it will jam and will not open the door. To solve the problem, you need to open the top cover (turn off the power to the machine first!) and find the automatic lock. Carefully remove any caught fabric using a screwdriver.

Handle damage

Forcibly opening the door may cause it to break; this should never be done. However, the handle can also become unusable due to simple wear and tear. The washing machine door consists of two plastic rims and glass between them. Fastening between them is carried out with self-tapping screws and latches. You can replace the door yourself by following a simple procedure:

For convenience, remove the door from its hinges.
Unscrew the screws connecting the rims.
Carefully separate both parts of the rim and set aside the one to which the handle is not attached.
On the other side of the door there is a handle and a tongue - this is a latch.
Disassemble the handle and unscrew it, remembering the procedure.
In the reverse order of what was written down during the disassembly of the old part, install the new one.
Reassemble the door and return it to its original place.

The hatch door is stuck and won't open

Sometimes it happens that after pausing the washing process and draining the water, the automatic unlocking of the hatch does not work. This reason mainly occurs when the lock latch is stuck. Forced opening of the hatch in this case is carried out using improvised means or by partially disassembling the machine body.

We use improvised means

If the lock on a front-loading washing machine clicks to the side, the door can be opened using a strong thread. The work process is carried out in the following order:

A thread is inserted between the door and the body of the machine.
Pull the thread and hook it onto the latch of the lock.
Pull both ends of the thread at the same time and the hatch will open.

These works must be carried out extremely carefully, making sure that the thread does not break.

If there is no access to the lock between the hatch gap and the body, you will have to partially disassemble the car.

Opening the door with partial disassembly of the housing

Partial disassembly of the case must be carried out extremely carefully, otherwise the components may break. The process of opening the hatch is carried out in the following order:

The nuts are unscrewed from the top of the equipment and the cover is removed.
The washing machine tilts backwards.
The drum moves away from the hatch.
Once you have access to the lock, press it and open the door.
The parts of the washing machine are assembled into place.

Getting ready for an emergency opening

Desperate attempts to open the hatch may not yield a positive result. You need to understand when the failure occurred. If, some time after the wash is completed, the door cannot be opened, you can try to turn on one of the options: “Spin” or “Rinse”. If there is no result, you should check the drain hose; there may be problems due to blockage. In this case, cleaning is carried out and the laundry is then started to spin.

It often happens that after some time the unlocking occurs automatically; it is enough to disconnect the device cord from the power supply. The waiting time ranges from ten minutes to thirty minutes. If there is still no result, take immediate action by making sure that there is no water in the unit. To do this you need:

open the filter cover to collect debris;
find the emergency drain hose (usually located on the left side);
Place a deep basin next to the washing machine, open the cap and drain the water.

Preventing door locking problems

In order to reduce the likelihood of unprogrammed door locking, it is necessary to carry out preventive measures, then searching for answers to the question “How to unlock a washing machine?” will not need.

First of all, it is important to remember to maintain cleanliness

It is important to be careful when loading laundry and ensure safety. It is not recommended to load laundry that is too dirty, as this may contaminate the drainage hose.

The sole of the shoe must be cleaned of dirt before starting. If possible, it is advisable to use additional water softeners to avoid limescale deposits.

It is not recommended to load laundry that is too dirty, as this may contaminate the drainage hose. The sole of the shoe must be cleaned of dirt before starting. If possible, it is advisable to use additional water softeners to avoid limescale deposits.

Before directly immersing yourself in the drum, you must remove all metal jewelry from clothing that may cause damage during operation. This is especially true for small parts that can get into hard-to-reach places inside the car and, in particular, damage the hatch lock.

Video: opening the machine door:

After purchasing the equipment, you must carefully read the instruction manual to avoid accidental connection of functions and prompt and correct action in case of breakdowns. It is best to keep such documents in sight at all times.

Unlocking secrets for different car brands

To successfully correct problems, you must carefully read the instructions for the washing machine, since equipment from different manufacturers differs in design.

Samsung . If such a situation occurred with a model of this brand, and draining and rebooting for 30 minutes did not bring the desired result, then there is a problem with water removal.

You will need to forcefully drain the water using the emergency hose, it is located next to the filter. In addition, especially for such situations, some models provide cables for forced opening of the door.

Additional information on troubleshooting problems with Samsung washing machines is provided in this article.

LG . You can simply unlock a car of this brand by removing the “Child Lock”. To reset, as well as to install, you must simultaneously activate two modes: “Super Rinse” and “Pre-Wash”. The cycle can then be continued by selecting the Start/Pause button.

Washing machines from LG are easy to unlock; to do this, you need to remove the “Child Lock” mode or hold down the “Start” button for a couple of seconds.

Bosch . To unlock a washing machine of this brand, press the “minus” button. This method will work if your model has plus and minus buttons on the panel.

If the key is lit on the monitor and there is no way to change the mode, you must hold the “Start” button for 5-10 seconds. After this, the hatch will open. Deciphering error codes and tips for repairing Bosch equipment are given here.

Electrolux . All machines from this manufacturer are equipped with a “Pause” function, using which you can complete the wash ahead of schedule. If the water level in the drum reaches a certain point and the temperature drops below +50 °C, the lock will automatically open.

Atlant . Washing machines of this brand are equipped with an emergency hatch opening system. For this purpose, a special cable is installed to open the door next to the drainage filter.

To unlock the Atalnt machine, you need to find an emergency release device for the hatch locking device. It is installed next to the water filter at the bottom of the device

Indesit . Owners of a washing machine of this brand should first check the presence of water in the drum. If it is missing, then you should restart the machine.

When you don’t have time and you need to quickly open the door, just carefully pull the emergency rope, which is located at the bottom of the unit.

If there is water left inside the washer, then activate the “Drain” mode. If this does not help, then you need to manually remove the water from the machine using the drain hose. After this, the machine will unlock automatically. If this does not happen, then use one of the methods described above to force the hatch to open.

Ariston . In units from this manufacturer, the door is blocked due to power surges or as a consequence after a power outage.

To deal with such a breakdown yourself, you have to remove the water. Here, either an emergency release cable or manual drainage of water will help you. Both parts are located in the lower right corner of the machine near the filter

The instructions contain Ariston error codes, probable causes of failure and possible solutions to the problem.

Selecting the “Baby”, “Silk” or “Easy Ironing” programs may cause the drum to slow down or the water may not drain completely. To correct the situation, activate the “START/PAUSE” button or duplicate “Easy ironing”.

Failure of the automatic washing machine hatch locking device

The reason that the washing machine door does not open after washing may be a malfunction of the UBL unit. To open the door, you will need to disengage the door lock manually. You can do this as follows:

Remove the top cover of the machine and tilt the device body slightly back. This action will move the drum and open access to the latch. Then press it out and open the door.
If you have sufficient confidence in your abilities and skills, replacing a faulty UBL with a new one will not be difficult. First of all:
We disassemble and remove the rim - retainer. Opening access to the right side of the door cuff.
We unscrew the two screws securing the hatch locking device and remove it, having previously freed it from the wires connected to the UBL and remembering their connection diagram.
We install a new unit with an electrical connection, assemble and hang the door.
We conduct trial testing of an automatic washing machine.

Workshop "RemBytTech" - repair of washing machines with a guarantee

If after the next wash you find that the door of your LG washing machine is blocked, and you are unable to fix the problem on your own, contact the RemBytTech workshop. On the company's website you can study in more detail what certain errors in LG washing machines mean, and also consider the procedure for eliminating them.

Video. Washing machine door won't open

Video. The washing machine does not drain water

Imagine the situation: an LG machine finishes washing and signals the user about it. The housewife approaches the machine to remove the laundry, but cannot do this because the door remains locked. That’s the trick, the machine doesn’t return the laundry, “it would be funny if it weren’t so sad.” For what reason does the door of an LG washing machine not open after washing? Let's all figure it out together.

Lock or handle?

Often the desire to quickly open the hatch door ends with a damaged handle and a broken lock. This is exactly how the machine will react to attempts to bypass the blockage with force and pressure. For those who have not calculated their power, an alternative option is offered for opening the washing machine.

Measure the circumference of the door.
Prepare a cord with a diameter of less than 5 millimeters and a length that should be equal to the circumference of the door plus 25 centimeters.
Carefully insert the rope into the gap between the door and the body (if necessary, you can use a flat-head screwdriver or other similar tool).
Pull slowly on both ends of the lace.

It is worth understanding that opening the door will not solve the problem of a broken locking mechanism. A faulty lock will have to be replaced. It will not be easy to cope with such a matter on your own: you need to find a suitable part, partially disassemble the unit and return everything to its original place. Therefore, it is better not to experiment with DIY repairs and entrust the lock change to a specialist from the repair service.

Don’t despair if the machine refuses to open the door during washing. Moreover, there is no need to panic and try to forcefully solve the problem: the blockage can be removed quickly and easily. The main thing is to be patient and consistently follow all the steps described. And only after you’ve tried all the options yourself and haven’t found a solution, you should contact a Samsung washing machine repair technician.

Interesting:

How to open the door of a Bosch washing machine?
How to unlock an Ariston washing machine
How to open an Atlant washing machine if it...
Rating of Samsung washing machines
How to open the door of a Haier washing machine?
The door does not open after washing in a Bosch washing machine

1 reader comment

03/31/2020 at 09:10
Lily:
Thank you, you helped
Answer

Troubleshooting

Most of the faults can be fixed with your own hands, after carefully studying the manufacturer's instructions, which describe in detail all possible cases of such breakdowns. With the exception of problems in the operation of the UBL intelligent module, when repairing it may require a complete re-firmware of the electronic control. And therefore, the services of a specialist from a specialized center for the repair of washing machines. Or serious breakdowns associated with the drum of the washing machine:

the drain pump has failed;
there is a blockage in the drain;
the control module is faulty;
The electronic water sensor does not work.

And if the blockage can be easily detected and removed on your own, then in other cases it is better to seek the help of professionals.

Door opening methods

What should I do if at the end of the wash the lock does not unlock and the loading hatch does not open? Since the cause of the incident may be a malfunction of the control system, you can start by rebooting the equipment.

Rice. 2 - Opening the door

In a similar way, you can try to repair washing machines of other brands (Bosch, Samsung, Candy), since the same factors can block the door as in the Indesit machine.

You will need to turn off the washing machine for a short time by unplugging the power cord from the outlet, for about 30 minutes. After switching on, the hatch should open. If the door is still locked, restarting the wash may help. In this case, it is enough to select the mode with the shortest program.

Let's say it didn't help. The locking device may have broken down. This mechanical problem most often occurs due to the fault of the owners. Users pull the handle in a hurry, resulting in damage to the latch or spring. Let's figure out how to open a washing machine if the handle is broken, without damaging the unit.

With a rope

Rice. 3 — Lanyard for opening the door

You can open the door in a washing machine yourself using a strong, but not very thick rope or cord. Helping with a screwdriver, you need to insert the rope into the crack of the hatch along its entire circumference. Then forcefully pull both ends towards you. During this manipulation, the latch inside the lock will move away and the door can be opened.

Door handle repair

Remove the door from its hinges;
We unscrew the screws holding the 2 rims of the lid together and carefully disassemble the door itself;
The handle mechanism is located on one of the rims. We check the serviceability of the lock latch and, if necessary, repair it. Technically, the locking mechanism is very simple and does not present any difficulties in repair;
At the last stage, we assemble the hatch in the opposite order and check that it works properly.

Front loading

To open the door of a front-loading washing machine, there are several rules. Opening methods depend on the operating stage of the machine. Therefore, in order to avoid mistakes at the initial stage of opening the hatch, you need to familiarize yourself with the sequence of work.

Opening at the beginning of the wash

If you need to open the washing machine at the beginning of the wash cycle, when the drum has not yet filled with water, you can use the “Pause” button. If this mode is not available, to temporarily pause washing, you will need to press the “On” button. At the same time, in order for the door to open automatically, the press must be quick, otherwise the selected washing mode will be turned off. Once the door is closed, the machine will resume paused operation when you press start.

During washing

In order to open the door of the washing machine during operation, when the drum is already filled with water, canceling the wash alone will not be enough. In this case, water removal will be necessary.

The process of opening the hatch itself is performed in the following sequence:

Without unplugging the cord from the outlet, press the “Pause” button.
When the machine pauses, turn on the spin mode, while simultaneously selecting its cancellation.

As soon as the water is drained, the loading drum will open automatically.

Often, when canceling a wash, the functionality of the buttons is impaired. To resume operation, it is recommended to disconnect the washing machine from the power source for 10–15 minutes. After this time, having connected the equipment to the power supply, you can try to open the hatch.

The LG washing machine has stopped running with water and does not drain; the hatch is blocked. Error OE on display

The washing machine may not drain water due to:

A failed pump. Voltage fluctuations and small objects getting into the pump can cause it to malfunction. A new part will need to be installed.
Faulty pressure switch (water level sensor). The washing machine “does not understand” how much water is in the tank and therefore does not start draining. The problem can be solved by blowing out the pressure switch tube or installing a new sensor.
Blockage (in the drain filter, pipe, hose or sewer). It is necessary to check the water drain filter, as well as the drain pipe and hose of the washing machine for blockages. In some cases (for example, if there is a blockage in the drain pipe), this may require disassembling the washing machine body, however, if you have never done such work, it is better to call a professional technician.
Burnt out control board. The signal from the control board does not reach the pump, so the washing machine does not start draining. It is necessary to replace the burnt-out board elements, or install a new board to replace the faulty one.

Important!

Do not try to open the washing machine door by force! Before you take active steps to fix the problem, drain the water from the washing machine by unscrewing the filter on its front.

An additional symptom indicating problems with water drainage is the appearance of an OE error code on the washing machine display. Machines without screens report a fault as follows:

the rinse indicators light up or flash simultaneously;
The spin indicators 800, 500 and No spin are lit or flashing simultaneously.

What to do?

When deciding how to open the hatch door, you should analyze the condition of the machine and consider possible causes. In all cases, you need to act carefully, slowly. Some door opening options may require outside assistance.

Blockage as a reason for blocking

If the car door does not open, you need to inspect it. If the machine breaks down with laundry inside and there is water in the drum, most likely there is a failure in the drainage system.

The procedure in this case:

run only the “Spin” mode without washing;
if the water drains, it means there was an accidental failure in control;
if draining does not occur, the machine should be turned off and the blockage should be cleared;
After the drain hose has been restored, start the “spin” mode again.

After finishing the spin cycle and draining the water, the door should open in 1-2 minutes.

Failure in the control module

In some cases, a locked door may be the result of a faulty control board.

Procedure:

Unplug the machine by removing the plug from the socket.
Wait 20-30 minutes.
Turn on the car.
Try to open the door.
If the door still does not open, proceed to the next step.
Start the washing program. In this case, the machine will first have to unlock the door, and then lock it again and begin the cycle. The task is to wait for the moment when the unlocking occurs and interrupt the running program.

A characteristic click signals the door unlocking. This moment cannot be missed.

Emergency opening: what does the manufacturer offer?

All models of Samsung washing machines have the ability to open the door in an emergency.

This function is available using the built-in cable:

Open the hatch with the filter, which is located on the front panel at the bottom right.
Find the cable fastening. It should be painted in a bright color - yellow, red or orange.
Pull the cable lightly to release the lock.

If there is water in the washing machine, you should prepare a large rag in advance to absorb it when you open the door.

Manual opening of the lock: access from above

If you couldn’t find the emergency opening cable, you can go another way:

disconnect the washing machine from the power supply;
shut off the water supply;
pull out the washing machine so as to gain access to its rear wall;
in the upper part of the rear panel, find the screws holding the top cover and unscrew them;
pull the cover towards the rear wall and remove it;
tilt the washing machine back so that the tank moves and you can see the door lock latch from above;
find the tab that serves to lock the door and move it away.

You can do all of the above manipulations after draining the water.

Opening with a cord

This method can help open the washing machine even if the handle or the latch mechanism itself is broken as a result of inept actions or wear.

For manipulation you will need a cord with the following parameters:

the length is equal to the sum of the door circumference plus 25 cm;
the cross-sectional diameter must be 0.5 cm (to fit into the gap between the hatch cover and the front panel of the device).

Procedure:

Insert the cord between the door and the washing machine body itself. You can help yourself with a flat-tip screwdriver or other similar non-sharp tool.
Pull the free ends of the cord so that pressure is created on the area with the lock.

If the door is already broken, opening it will only solve part of the problem. Next, you need to diagnose and repair or replace the damaged part.

This is not always possible to do on your own. Washing appliance repair specialists will come to your aid.

This method is clearly shown in the following video:

How to open the machine correctly?

If, despite your expectations, the hatch of the LG washing machine does not open, you will have to urgently open the door and take out the laundry. Of course, we won’t break the lock using a nail puller or sledgehammer; there are much more humane methods.

First, we check whether the machine is de-energized.
If the length of the hoses allows, push the washing machine towards you to gain access to the top cover. The inlet and drain hoses may need to be disconnected; in this case, be sure to turn off the water supply.
Next, you need to remove the top cover of the washing machine.
Through the hole formed at the top, we put our hand down and move the UBL flag. The device is located approximately at the level of the door handle, so to quickly detect the emergency opening flag, shine a flashlight there.
While moving the flag with one hand, you must open the hatch door with the fingers of the other hand.

That's all, we managed to open the door this time, but the fact is that during the next wash the fault will manifest itself again. In order not to disassemble the LG washing machine after each wash, you need to determine the causes of the malfunction and carry out the repair yourself.

What to do if it doesn’t open after washing

Experts say that one of the most common questions from customers is how to open a washing machine if it is locked.

The fact is that different models may have different unlocking methods. However, there are several universal actions. Before performing any of them, you need to prepare:

If the door does not work, repairing or inspecting the device connected to the network is strictly prohibited. First of all, you need to turn off the power supply.
There should be no water left in the drum. It is drained in any available way. When the “Drain” function cannot be used, the water is removed through the filter.
When an unfamiliar code appears on the display, its meaning is found in the instructions. In most cases, to open the car door, it is enough to follow the suggested recommendations.
Before disassembling the equipment, it is worth checking the length of the warranty period. If it has not yet expired, it is not recommended to act independently, because... this will result in additional costs and void the warranty.

Using a rope

If the door does not open, one of the easiest ways to solve the problem is to use a thin rope or cord. This option is effective when the handle on the door is broken or the latch is jammed. To do this you will need a long rope and a flathead screwdriver.

The rope is threaded between the body of the device and the manhole cover

The most convenient way to do this is with a screwdriver (be careful not to scratch the case). When the rope is threaded from the side of the lock, pull both ends towards you

At this time the lock opens.

Power off

In this way, you can open the washing machine if it is locked after a program failure or freezes. To restart the program, the device is disconnected from the network and connected after a couple of minutes. The need to reconnect is explained by the fact that in the first seconds after connecting the machine, the module checks the state of the door. At this point, unlocking and re-closing most often occurs.

Emergency opening cable

When the hatch on the washing machine does not open, you can solve the problem using an emergency cable. It is located next to the filter; to get to it, remove the front lower panel of the device. The cable is painted yellow or red. By pulling it, you can quickly remove the door lock.

In rare cases, the devices do not have an emergency cable, then the work of opening the lock will have to be done manually. To do this, you will need an assistant whose task is to tilt the machine back slightly. Under the influence of gravity, the drum will also deflect slightly. This will allow you to put your hand behind the front panel and find the lock there.

The part is carefully moved to the side, after which the lock is removed

Experts warn that using a cable opens a locked door, but does not solve the main problem. If the damage is not repaired, the door will stop opening the next time you wash it.

How to unlock an Indesit washing machine

To unlock its door, you first need to make sure that the machine has completely pumped out the water from the drum.

If there is no water in the machine, try to correct the situation by completely rebooting the software - unplug the plug from the socket and let it stand for about half an hour. During this time, the program will be reset and the door will unlock. If you don’t have time to wait for such a long time, activate the washing mode again. Before it starts, the machine will first reset the lock, and then start it again. A sound signal will notify you that the washing machine door has opened. All that needs to be done at this moment is to open the hatch door and cancel the wash.

Another solution is to use an emergency opening cable located at the bottom of the unit; if water remains, use the “Drain” function. If it is faulty, you will have to drain the water yourself using a drain hose. Then, use the previously discussed troubleshooting methods.