What bearings are on the Indesit washing machine? How to replace a bearing on an Indesit washing machine

Replacing the bearing in the Indesit WIS washing machine. Preparatory stage

After identifying the malfunction, you need to properly prepare to repair the machine. Bearing replacement work requires certain skills and knowledge of the unit. The most difficult thing in this process is getting to the worn parts. To carry out sequential bearing replacement in an Indesit washing machine with your own hands, you will have to completely disassemble the unit, which will take a lot of time and effort.

Before starting repairs, prepare all the necessary tools

If you decide to make the replacement at home, you should first prepare all the necessary tools. This will allow you to concentrate on the process of disassembling the device and not run to the garage for every little thing. To replace the bearing, gather the following tools:

1. Open-end and socket wrenches.
2. Hammer.
3. Phillips and flathead screwdrivers.
4. Pliers.
5. Bit.
6. A hacksaw or grinder.
7. Softener WD-40.
8. Sealant or glue.
9. New replacement parts.

To choose the right new bearings and seals for your Indesit machine, you need to know which elements are installed in your equipment. For example, for the WISL 85 EX model, bearings of type 2o4 and 2o5 are suitable, while for the Indesit WI 101 EX washing machine, parts designated 2o2 and 2o3 are needed. It is best to remove the old bearings and seals and take them with you to the store before purchasing to select similar items. Be sure to purchase two oil seals and bearings at once, even if only one part breaks. If you miss this moment, you will soon need to change all the elements again.

If you doubt your abilities, the right decision would be not to try to fix the machine yourself, but to immediately entrust the repair to an experienced specialist from the service center.

Before starting disassembly, disconnect the unit from the mains and unscrew the intake hose, first turning off the water supply tap. Then disconnect the drain hose from the sewer pipe. If there is any water left in the machine, it must be drained through the filtration compartment located below behind a small panel.

Table of spare parts for Indesit washing machines (bearings, oil seals, drive belts)

WITH

An alnik (tank cuff, sometimes called a rubber drum gasket) for a washing machine is used as a contact-type sealing device for rotating shafts.
The function that the oil seals perform always remains the same, but the dimensions and profile configuration are different. Most often, two types of seals are used: single-lip (used to prevent leakage) and single-lip with boot (used to prevent leakage and to ensure the protection of the connection from the accumulation of dust inside it). nbsp; When assembling the bearing assembly of a washing machine, the oil seal, pressed into the tub hub or crosspiece with its working edge, forms a friction pair with the drum shaft. All oil seals have a metal reinforcing insert inside, so during installation, special care should be taken to avoid its deformation. nbsp; There are seals with a V-shaped profile (V-RING), which are used in conjunction with a reflective disk rigidly attached to the tank. The peculiarity is that when installed on the axle shaft, it is tightly pressed with its V-shaped edges to the disk. Wirings are used in top-loading washing machines. Indesit
washing machines from us: St. Petersburg (St. Petersburg), Marshala Kazakova St., 35. YUNONA Market, pavilion 341.

ATTENTION!

The table is for informational purposes only! Some washing machine models may have other sets of bearings and seals installed depending on the year of manufacture and serial number!!!

Bearings and seals for non-separable tanks of washing machines Indesit (Indesit), Ariston (Ariston), Hot Point Ariston (Hot Point Ariston)

<< to the top of the page <<to the page for choosing a washing machine brand

We are waiting for your calls.

Replacing a bearing in a Samsung washing machine. How to replace a bearing in a Samsung washing machine

Replacing the drum bearing of a Samsung washing machine is a common procedure in workshops and service centers. This part experiences heavy loads during operation and therefore often fails. Replacing the bearing of a Samsung washing machine with your own hands is painstaking, troublesome work. This is due to the design features. The back wall of Samsung models is solid and cannot be removed. Be prepared for the fact that the machine will have to be disassembled almost down to the screw in order to get to the drum. By conscientiously removing all interfering parts, you will maintain their integrity when removing the tank. Ready to bring your washer back to life? We will help you with practical advice and links to useful resources.

Step one - selection of parts

To find a suitable repair kit, you will need the full model name. It is located above the barcode of the service sticker, on the back wall of the washer.

Take a photo or write down the name - specialists will help you select a spare part. The required modification may be indicated in the table.

Then it’s easy to buy a bearing in an online store. The last way is to disassemble the machine to see what bearings are in the Samsung washing machine. This option has one big advantage - by dismantling the SM parts, you can find other defects, breakdowns (belt, crosspiece, pipes), and immediately buy everything you need.

How much does a bearing cost for a Samsung SM?

The price varies from 100 to 700 rubles. To replace, you will need 2 bearings - internal, external, and a new seal is required. Therefore, it is more advisable to purchase. Cost: 1000–2000 rubles.

Step two - preparation

First, prepare the machine for the procedure:

1. Disconnect from the electrical network and communications.
2. Move it away from the wall, out of a closet, a niche, from under the sink - you will need room to maneuver, good lighting.
3. Stock up on tools: a set of screwdrivers, a screwdriver, socket wrenches, a hammer, a rag, lubricant, a repair kit, a marker, a camera, a screw press.
4. Prepare a place for the removed components, panels, and fasteners.

Step three - dismantling the SMA

The main process will also have to be carried out in several stages. Don’t forget to photograph the results of your labors and film them. This will make it easier to put everything back together. Let's get started:

1. Remove the top cover:

• Select a suitable screwdriver, an attachment for your favorite screwdriver, and unscrew the rear bolts that secure the cover.
• Pay attention to the presence of plastic washers and gaskets - put everything in one place so as not to lose it.
• Push the cover away from the front so that the fasteners come out of the grooves.
• When the surface moves forward, lift it up and carefully remove it.

1. Remove the powder receptacle by pressing the inner latch with your finger.
2. You will have access to two self-tapping screws that hold the front panel and the powder receiver hopper - unscrew them.

1. Remove the control panel by disconnecting the wires. Samsung SM wiring is done wisely. The terminals and connectors are designed in different shapes and colors, so it will be difficult to confuse anything during reassembly. But if you are in doubt, you can take a photo and number it with a marker.
2. Once you remove the module, you will see the screws that hold the top of the main front wall.
3. Disconnect the bottom panel by carefully prying it with a screwdriver - this will give access to the lower wall fasteners.
4. Before unscrewing the main screws, remove the metal clamp securing the hatch cuff. To do this, pry up the spring with a flat screwdriver.

Thread the cuff into the drum. Now you can remove the front panel.

1. Now that access to the internal components is open, remove the water supply valve, filler and air pipes, and carefully disconnect the water level sensor.

1. When removing the drain pipe at the bottom of the machine, place a container - there is often water left in it after washing.
2. Disconnect the wiring of the lower part - heating element, motor, pump, sensors, grounding. Move the bundle of wires to the side, secure it so that it does not interfere or is damaged when removing other parts.
3. Use a socket wrench to unscrew the shock absorber mounts and concrete counterweights.
4. Now you can pull out the plastic tank by removing it from the springs.
5. Remove all elements that may interfere: motor, belt, shock absorbers.
6. Separate the halves of the tank by prying the metal spring-latches around the perimeter of the tank.

1. Remove the pulley. A socket wrench with a 17mm head will come in handy.

1. Carefully knock out the shaft with a hammer and remove the drum.
2. The rear cover of the tank contains bearings and an oil seal.

1. Before replacing the kit, pay attention to the seat. If there is a large wear on the shaft or nicks, it makes sense to change the crosspiece, otherwise replacing the bearings will not give the desired effect.

How to change:

1. Remove the oil seal.
2. Carefully drive the large bearing inside the tank wall, and knock the small one out.
3. Clean the bushing from scale and rust, and lubricate it with a special lubricant.
4. Lubricate the oil seal and rings - put them in place.
5. Ready!
   All that remains is to reassemble the washer in reverse order. You will be able to carry out the dismantling, repair, and assembly procedures yourself. As you can see, the scope of work ahead is no joke. But if you are a techie at heart, have a set of tools, the necessary components, you can handle this task step by step. We wish you a successful renovation!

How does a bearing work?

In the standard assembly, two bearings are installed inside the washing machine, which connect the drum and pulley.
These parts have different sizes, the large bearing is located near the drum and carries a fairly high load.

The small one is located at the opposite end of the shaft.

With the help of bearings, the washing machine drum rotates evenly when performing the program and additional functions.

Causes of wear

Replacing the bearing of an Indesit machine, with proper operation, may only be required after five to six years of operation of the device. This is no longer a breakdown, but natural wear and tear.

If you have a breakdown, that is, not even 5 years have passed from the date of purchase, then most likely this happened due to :

• constant overload of laundry, hence imbalance during operation and premature wear of components;
• a damaged oil seal, which protects the bearing from water penetration thanks to lubrication. If the seal is leaking, water will seep in and wash away the lubricant, causing the bearing to corrode and break.

External signs of bearing failure:

• leak under the washing machine;
• When spinning, there is a loud noise and grinding noise.

Also, you can twist the drum, if you see any play between the drum and the tank, then you should be wary.