Instructions and manual for Beko WKL 13560 K in Russian

+7

Is your BEKO washing machine broken? We will provide free consultation on the causes of the breakdown and on-site consultation. Only professional specialists in VEKO machines, guaranteed results from professionals with 7 years of experience!

We will carry out urgent repairs of your Beko washing machine at your home. Operational departure in Moscow and the nearest Moscow region. We repair VEKO washing machines in Podolsk, Balashikha, Mytishchi, Odintsovo, Pushkino, Krasnogorsk, Shchelkovo and other areas of the Moscow region +20 km from Moscow. A technician's visit for diagnostics costs 0 rubles.

from 330 rub.

Order repairs

Call a BEKO machine technician

Most people who use washing machines at home have repeatedly noted the reliability of household appliances manufactured 10-15 years ago.
However, even such machines are running out of service life. Our specialist will come to you exactly at the appointed time, agreed upon in advance, for diagnostics or repairs. To submit an application, simply use the website option or call.

So that the master can adequately prepare for the visit, be sure to indicate:

• manufacturer and model, according to the instructions for the washing machine;
• the essence of the malfunction - what does not work and how it does not work;
• urgency;
• your contacts.
• Beko washing machine error codes

Electrical repair

Only users with electrical repair skills can cope with this task. If there is a break or oxidation of contacts somewhere, they will quickly fix the problem. All you need for Beko electrical repair work is a circuit diagram. Where can I get it? It is enough to know the exact name of the model to find it on the manufacturer’s website.

It is much more difficult with electronics - to repair or replace the control board, you need special knowledge and skills. The cost of the electronic module is high - reaching a third of the price of the entire SMA. Therefore, it is not recommended to touch it - it is better to trust a specialist. If the repair is minor, then repairing the module will not cost much. But independent experiments can lead to complete failure of the module - you will have to purchase a replacement for it, and a simple problem will transform into expensive repair work.

Select your model

• BEKO WRS 55P2 BSW
• BEKO WKB 51001 M
• BEKO WKB 41001
• BEKO WKB 61031
• BEKO WKB 51031 PTM
• BEKO WKB 61001
• BEKO WKY 60831
• BEKO WKB 61041
• BEKO WKB 61021
• BEKO MVB 59001
• BEKO WKB 50821 PT
• BEKO MVB 69001
• BEKO WKY 71231
• BEKO WDW 85120
• BEKO WKY 61031
• BEKO WKY 71031
• BEKO WKB 61231 PTYA
• BEKO WKY 71021
• BEKO WKB 60821
• BEKO WKB 50801
• BEKO WRE 64P1

Typical BEKO faults

Malfunctions of the Beko washing machine are most often typical - typical for all brands. They account for approximately 90% of all breakdowns.

Doesn't turn on

The washing machine may not turn on due to a failure of the start button, a breakdown of the control element, or a malfunction in the interference filter.
from 400 rub.

Leaking

This usually happens with models that have been in use for a long time, given the gradual wear of the seals, but a similar problem also happens with new machines.
from 550 rub.

Doesn't drain

This malfunction is one of the most common.
The reasons may be different: from a banal blockage in the filter to a breakdown of the electronic control module of the machine. from 330 rub.

Does not open

Here, under no circumstances should physical force be used, as there is a risk of damaging the part, and it will not be possible to open the hatch in this way.
from 450 rub.

Doesn't wring out

Problems with the drain pump (pump) are one of the most common reasons why the washing machine does not spin.
from 350 rub.

Doesn't take up water

The result of a breakdown is the appearance of a corresponding error on the display or the equipment freezing due to a program failure.
from 350 rub.

Doesn't heat water

A freezing washing machine is a fairly common problem associated with its technical design.
from 330 rub.

The door does not lock

If the washing machine does not close when you want to start the wash, the door does not slam or is not blocked, the reasons for the malfunction vary
from 350 RUR.

The drum does not spin

There can be several reasons for the malfunction, from the simplest ones, which can be eliminated on your own, to those requiring professional repairs
from 600 rubles.

Common VECO malfunctions and their features

If you notice that, despite the set washing program in warm water, the water is still cold, this is most likely due to a breakdown in the control board or a malfunction of the heating element.
The same conclusion can be drawn if the water is hotter than the set temperature. It is worth noting that when the water overheats, failure of the control board is more likely, but the heating element may also break down. In any case, both options must be confirmed or excluded.

If the washing machine is very noisy, grinding and knocking, there is a possibility that the bearings are broken or a metal object has gotten into the tank, stuck between the wall of the tank and the drum. In this situation, you should immediately turn off the machine and perform all corrective actions.

How to resolve failures

Let's figure out how to repair Beko washing machines on your own.

1. Problems with draining water.

You should know that after washing by machine, the waste water is not clean and transparent. To prevent various small debris and dirt from clogging the pump, a special filter is installed in front of it, which in most cases becomes clogged. The main task is to find this element, which is usually located at the bottom of the machine, under a small hatch or panel.

Further actions should occur in the following sequence:

• Before removing the filter, place a basin on the floor or spread a rag to collect waste water, which will definitely flow out of the hole. Some models of machines are equipped with a hose for emergency drainage of water,
• in order to remove the filter, it should be turned to the right,
• After this, the filter is cleaned and washed under running water,
• using a screwdriver you can clear the pipe, which may also be clogged,
• For preventive purposes, you can clean the filter installed on the water intake (it is located at the point where the intake hose is attached to the rear wall). As a rule, rust particles and sand found in tap water accumulate in it,
• After cleaning the intake filter, you should not rush to install it in its original place - you should also inspect the drain pump itself. Quite often, machines with their own diagnostic system detect pump failure and give a signal about it. But sometimes, if the faults are minor (the impeller is loose), the “controller” is not able to identify the problem,
• To check the pump, you need to activate the water drain mode and look into the plug hole to see how the impeller works. Rotation will indicate that everything is fine. If the element does not move, it is necessary to clean or completely replace the drain pump,
• Now you can install everything in its place, assemble the machine and carry out a test wash.

1. The water doesn't heat up well.

To cope with such a failure, you will have to partially disassemble the washing machine again. But first, it should be noted that in all machines, the thermal electric heater is one of the weakest components. People call it by a simple word - heating element. Under the influence of hot water, the mineral components located in the pipes begin to crystallize and accumulate on the heater in the form of ordinary scale. Plaque does not allow heat to pass to the water, so the heating element burns out. But if the water in the pipes is soft and scale does not appear, or you use special means, then the heating element can still burn out, since it has its own working life.

In order to make sure exactly what happened to the heating element, you need to get to it. The peculiarity is that in different models it is located both in the front and in the back. For the first case, the steps are as follows:

• The front panel of the machine is removed. But first you need to remove the cuff from the door. You must act carefully so as not to damage it,
• two contacts with wires connected to them will stick out in front of you, which need to be disconnected,
• You need to check the resistance using a tester. Under normal conditions, its value will be from 25 to 30 Ohms. In other cases, we can confidently assume that the heating element has failed,

• unscrew the nut holding the heating element under the drum from the bolt, carefully pull out the heating element,
• we clean the place for its installation from plaque and accumulated debris,
• install a new analogue, connect the wires.

If the heater is working properly, you should check the temperature sensor located under the top panel.

To do this you need:

• unscrew the screws and remove the top panel,
• the sensor is dismantled along with the detergent tray and the control panel, since all this creates interference in getting to the element of interest to us,
• Having opened access to the sensor, you must disconnect all wires from it,
• checking the resistance. Normally it should be 4.7 kOhm,
• The sensor must be kept in a container with warm water - the resistance indicator should decrease. Otherwise, the element must be replaced,
• the new sensor is installed in place, all work is performed in the reverse order.

1. Do-it-yourself electrical and electronics repair.

If you have special knowledge and the necessary experience in repairing electrical appliances, then you can eliminate a broken contact or terminal oxidation quite quickly. All you need is a wiring diagram for the machine, which can be found in the instruction manual.

But with electronics it’s not so simple. Repair work or replacement of the control board requires special knowledge and experience. Considering the cost of a new module, you should not attempt to repair it yourself. In this case, it is better to invite a master who will do everything himself.

1. Washing machine vibration.

During operation of the unit for washing clothes, in particular during the spin cycle, the machine produces strong vibrations and begins to “jump” in different directions. Pay attention to how much laundry is loaded. Vibration is possible if the maximum limit is exceeded. Another recommendation is to check whether the SMA support legs are adjusted correctly. They are leveled so that the device does not wobble. Experts advise using special stands when installing the machine.

BEKO washing machine service center

Troubleshooting at home and replacing broken parts will ensure that the washing machine works well and has a long service life.

Among the advantages of our service center it is worth highlighting:

• specialist experience of 7 years,
• after-service warranty of 1 year,
• original spare parts,
• free diagnostics at home in all districts of Moscow.

To order repairs in Moscow at home, you need to call the contact number.

How we are working?

1. Leave an online request or call us at +7 495 134-83-15
2. We will advise you by phone
3. We will send a specialist to you for free diagnostics and accurate cost calculation.
4. The technician will carry out the repair work
5. You will be given certificates of completed work and a warranty card.

What are the features of the renovation?

Models from Beko have design advantages that are especially useful when replacing bearings:

• The device is much easier to disassemble than most analogues from other brands.
• Usually you don't even have to take out the tank to replace the bearing.
• Simply remove the front of the tank to remove the drum. The back remains in place.
• It is necessary to remove the entire tank when the bearing is destroyed - when it is necessary to remove its remains.

What other features of disassembly:

• To gain access to the front of the tank, remove the front panel. Next, unscrew the lower counterweight. Disconnect all tubes and wiring.

Advice. Before disconnecting the wires, fix the original position in the photo - this will help you later when you assemble the device.

• The front of the tank is held in place by 12 clamps - all of which must be removed to access it. Now all that remains is to remove the back panel, remove the pulley mounted on the drum axle shaft, and then remove the drum itself. Please note that the bearings fit on the axle shaft with an interference fit, so it must be knocked out by carefully striking it with a rubberized hammer.

The screw connection holding the pulley on the drum shaft must not be removed.

Advantages of our workshop

· Wide range of services: diagnostics, installation of household appliances, configuration, repair, provision of warranty;

· Affordable prices. The cost of our service includes the price of parts that need to be replaced;

· Convenient work schedule. You can contact a specialist for help on weekdays, holidays and weekends.

· Large staff of professionals. This allows us to accept orders in Moscow, Moscow Region and other regions, carrying out even the most complex work with high quality.

· Use of original spare parts to ensure longevity and reliable service of the device.

· Prompt response to calls.

· Guarantee of quality of service, placing a mark in the product passport.

Error codes

If your washing machine is equipped with a display, then error codes will appear on the display. In models without it, you can see a combination of indicators that glow red when a breakdown occurs.