Dishwasher Indesit DSG 0517: malfunctions, operating instructions, the “wash and end” program indicator is flashing, pours water and immediately drains, reason

PMM Indesit 0517, which belongs to the category of compact kitchen appliances, is designed to load 10 sets of dishes. The product has proven itself to be reliable equipment designed for 5-7 years of service. Malfunctions that arise during operation of the Indesit DSG 0517 dishwasher are the result of the owner’s inattention to the product or arise due to natural wear and tear of the structure (production of the model was discontinued in 2013).

There is no reaction from the dishwasher when pressing buttons

If you turn on the dishwasher (DMM), but there is no light indication and the device does not respond to button presses, first check if there is power in the outlet to which the unit is powered. If everything is fine with the electricity, then the cause of the trouble may be oxidized contacts in the distribution box located inside the PMM. To access them you will have to disassemble the device.

The box is located at the bottom of the unit near the front panel. This area may be exposed to moisture, which leads to rapid oxidation of the contacts. Unscrew them and clean them with sandpaper, then screw the contacts into place and try to turn on the device.

If the breakdown persists, then the cause may be a faulty electronic control unit.

The machine control module is a complex electronic device that can be called the “brain” of the unit. It contains built-in programs and controls the entire “stuffing” of the PMM. Therefore, it is highly not recommended to repair this unit yourself. Only a qualified specialist can cope with the breakdown, and in this situation you cannot do without calling a specialist.

Examples of control panels

PMM Indesit control panels with 4/6 LEDs

Control panels for built-in Indesit PMMs with 4/6 LEDs

PMM Indesit control panels with digital LCD displays

Error codes for Indesit dishwashers

Over the many years that dishwashers have been produced under the Indesit brand, many models have been produced on several variants of technological platforms, with different electronic control boards, and with different types of user interfaces (control panels). For Indesit PMMs, the same platforms are used as for Ariston brand dishwashers and the error codes of both brands are almost completely the same.

In general, error codes for Indesit PMMs are standardized, but the problem with their display is that there are too many options: in this article we will try to describe the error code display of the most popular control boards (modules), and we will give examples of numerous design options for control panels of Indesit dishwashers.

See this article:

In order not to repeat the description of the same error codes, they will be fully listed only in the first table of codes (for DEA 601/602/700 boards), and all subsequent ones will refer to it, since the set of codes for different control modules often differs only in their indication.

EXAMPLES OF CONTROL PANELS

PMM Indesit control panels with 4/6 LEDs

Control panels for built-in Indesit PMMs with 4/6 LEDs

PMM Indesit control panels with digital LCD displays

Water supply stopped

This is a fairly common situation when there is a water supply in the water supply system, but it is not poured into the dishwasher. Dishwasher malfunctions may be caused by a clogged filter screen or a faulty fill valve. They are located at the very bottom of the device, at the connection point of the inlet hose.

To check these elements, you need to disconnect the device from the water supply and remove the panel. If the mesh is clogged, it should be washed under a strong stream of water.

You can verify the operation of the supply valve using a tester by “ringing” the winding of the coils. To do this, you will need to disconnect the wires from the coil terminals and measure the resistance:

Malfunctions and their elimination

Indesit DSG-0517 is durable. But sometimes troubles happen. If the indicator shows an error in operation. You need to find out its code in the instructions. Let's look at some malfunctions of the Indesit DSF-0517 dishwasher:

The device does not respond to buttons

It is recommended to check the nutrition first. There may be a problem with the outlet or cord. The contacts in the distribution box may oxidize. To fix this, you will have to disassemble the equipment.

No water supply

That is, the machine does not suck in liquid. It is worth checking the filter mesh, fill valve, hose (if it is twisted).

Water does not drain

If the Indesit DSF-0517 dishwasher is blinking and the indicator shows an error with drainage problems, it is worth inspecting the pump. It may become clogged with food debris. If the suspicion is confirmed, the pump must be disassembled, the filter replaced, or cleaned and reassembled.

Dishwasher pump

The car is leaking

A leak may occur due to the door not being closed tightly. Maybe it's time to change the seal.

Doesn't heat water

If the dishes are cold and greasy at the end of the cycle, it means they were washed at a cold temperature. It is worth checking the heating sensor, the serviceability of the heating element, and the timer.

At the end of the cycle, wet dishes

That is, the machine does not dry it. It is necessary to check the fan and the circuit connecting it to the system.

Indesit dsg 0517 instructions, specifications, forum

Answers 3

When connected to the network, the “wash” indicator starts blinking on its own, while something is working in the car. When you press the on/off button, everything resumes after 3-5 seconds. The machine does not respond to the start/pause button. The water supply filter is clean and there is water supply. The water drain filter is cleaned.

In the indesit dsg 0517 dishwasher, immediately after the water is filled, the “wash” and “end of cycle” indicators begin to flash, and the water is automatically drained. PS they already called a technician, he dug into it and said that everything was fine and all the hoses were CLEAN. But after that she worked for a day and everything started all over again. Please help, I will be very grateful!)

Answers 2

Hello! My machine 0517 has a new disease: it turns on, carries out 1 cycle, spits out a tablet, and then drains and the lights start flashing - “wash”, “finish”, “pause”. Pause does not respond to On/Off. ” If you press “Start”, then 1 cycle begins again, i.e. no heating occurs. What is the reason?

Which of the five modes has a temperature less than 65 degrees? Thank you.

Time of temperature conditions of the dishwasher INDESID DFG-051

It starts pumping water, then turns off and two indicators light up. What to do?

When connected to the network, the “wash” indicator starts blinking on its own, while something is working in the car. When you press the on/off button, everything resumes after 3-5 seconds. The machine does not respond to the start/pause button. The water supply filter is clean and there is water supply. The water drain filter is cleaned.

help me connect the board correctly. I deleted the photo with the connection without returning it.

What is the maximum water heating temperature?

Should the salt tank be full when purchasing?

Answers 2

The machine turns on, draws water, heats up, but there is no supply to the sprayers, the dishes are not washed. What to do? Thanks in advance, I'm waiting for your answer.

After the first use, the next morning the machine was filled with muddy water from the sewer system. How is this possible and for what reasons could this happen?

Answers 0

Where is the fuse located? no signal, won't turn on

When you plug in the machine, the “Wash” indicator immediately lights up and the drain motor runs. When you press the power button, it turns off briefly, and then everything repeats. Machine indesit dsg 0517.

The indesit dsg 0517 dishwasher does not heat up the water when washing dishes, what should I do?

After switching on, the machine runs for several minutes and stops at the same time, the washing indicator and the end of program indicator blink, what is this?

READ MORE: How much electricity and water does a dishwasher use | ENARGYS.RU | ENERGY SAVING

Answers 0

Hello, I have this problem: Water fills in, but does not wash, after a few minutes I open the door, the water stands still. When I press repeat wash, the water goes out and doesn’t come back in. I repeat on a different washing mode, the same thing repeats. What could it be?

Hello, can you tell me how to drain the water from a moving machine in a container? Thank you.

Hello, how do I drain the water to transport the machine in a container?

The dishwasher does not heat

The wash indicator and the end of the program flash simultaneously

The dishwasher takes a very long time to wash dishes and does not turn off. What is the reason?

Who knows what kind of spare part it is?

Good afternoon, please tell me, the dishwasher fills with water and immediately drains. Indesit.

Water leaks when washing

Answers 5

The machine does not pick up rinse aid.

Good day! Indesit dsg 051 the start-pause button is flashing. When you press this button, nothing happens. Is the button buggy or is it a block?

Please help with advice! I connected everything, turned it on, drew in water, then drained it and the wash and end lights (first and third) came on. What could be the matter? It’s connected to cold water, there’s salt, what else does it need?

Answers 0

Hello! The machine begins to fill with water, and the “Wash” and “End of Cycle” indicators begin to flash. The machine drains water. Tell me, what's the problem?

Good evening! During the washing process, the drying indicator and the start-pause indicator suddenly begin to flash quickly. What happened to the car? I can’t figure it out, I checked everything, either the drain sensor or the heater. Maybe someone can tell me?

Recently, when washing dishes, the drying of the dishes does not work. changing modes does not help. If it works, then you can tell through the race. what could be wrong with her? and what should be done?

dishwasher indesit dsg 0517 lights blink frequently pause washing and end what to do

water set cycle reset, water reset and light indication a05

Dishwasher Indesit DG0517. It collects water and immediately drains it without starting the wash, and during draining two indicators light up: the wash and the end of the wash. What could be the problem? Thank you.

Time is precious! The problem is a trifle. The kid hid the program spinner somewhere, I can’t turn on the desired program. The pliers don't help - it spins in a circle and doesn't touch 0. We haven't been able to find the switch for a year now, I think he threw it in the trash.

If anyone is not too lazy to remove the switch and take a photo, or draw, the position of the pin in certain programs, please do it. Now I set the program at random and calculate it based on time. The modes and time of their operation are pasted on the cabinet, the child did not get there. Bye…

Indesit 0517 DSG, does not heat the water and drains back. There was such a problem. I disassembled it myself and checked the heating element and pump for operation. Everything is working. I had to call a specialist. It turned out there was a break in the control board. Fixed it - everything works.

Good evening! During the washing process, towards the end, the drying indicator and the start-pause indicator suddenly begin to flash quickly. What happened to the car? What to do?

where is the fuse located in pmm indesit 0517

Answers 0

Hello. After washing, the dryer does not turn on and the “Start/Pause” indicator flashes frequently. What could it be? Thank you.

Good afternoon The car showed only its best side. In operation for more than 5 years. Recently, the following has begun to be observed: after washing, a black coating appears on the dishes.

In this case, only on the upper part of the dishes, which is located in the upper tray. We periodically carry out the washing cycle of the machine with a special product, but this does not give any results.

I ask for help in resolving this issue.

Indesit washing machine dsg 0517 the rinse and end of program lights are flashing.?

Where is the fuse located in PMM Indesit dsg 0517

How to repair it yourself

If there are minor faults, you can repair the Indesit ICD 661 dishwasher yourself.

Replacing the heating element

Due to the use of hard water, the heating element becomes covered with scale over time. The plaque layer increases, the heating element overheats and fails. Failure of this part increases energy costs. You can repair this part of the dishwasher as follows:

• the device is disconnected from the power supply network, the water supply tap is turned off;
• the car is turned over on its side;
• remove the bottom cover;
• inspect the pump (in Indesit dishwashers and washing machines the heating element is connected to this part; before removing the heater, you need to check the condition of the pump);
• replace the pump (if a malfunction is detected when checking with an ohmmeter, the part is replaced);
• disconnect the heating element wiring, check the contacts;
• remove the heating element (if the part is covered with a thick layer of plaque, unclench the clamps and disconnect the heater, then turn off the pump and remove the heating element from the housing);
• replace the pump seal;
• the protruding parts of the heater are treated with lubricant;
• install the heating element (the removed clamps are replaced with new ones).

Cleaning and replacing the drain pump

If PMM Indesit DSG 0517 does not drain water, check the drainage system after the program is completed. To do this you need:

• open the door, remove all trays and shelves;
• remove the mesh filter located at the bottom of the device;
• rinse the parts with a stream of water (if parts of the filter are very dirty, clean them with a brush);
• open the pump, inspect and clean the impeller;
• check the serviceability of the pump (you can get to this part through the bottom of the dishwasher);
• disconnect the wires and check the terminals using an ohmmeter;
• remove and replace the pump.

Replacing the door seal

When the seal becomes thin or dislodged, the machine begins to leak. You can replace the part yourself. To do this you need to do the following:

• open the camera door;
• remove the seal around the perimeter of the opening;
• take a new gasket and install it, straightening it around the perimeter;
• cut off excess material with a knife;
• evaluate the quality of installation by starting the machine.

To replace the lower seal you need:

• open the hopper door;
• Unscrew the screws located on the inside of the door;
• lift the door, pull, remove the outer panel;
• open the door again, remove the basket from the chamber (the seal is visible at the bottom);
• remove the cushioning material by grasping its edge with tweezers;
• insert a new seal (there is a mark on the right side of the product to facilitate the installation process);
• assemble the door.

Problems with the control board

The control unit is an expensive and fragile part. Each part of the module is responsible for the functioning of certain elements of the machine. It is recommended to trust the repair of the board to specialists. Checking a part includes the following steps:

• removing the front door panel;
• removing the clamps holding the control panel;
• disconnecting the wire connected to the module;
• removing the bolts connecting the board to the panel;
• disconnecting the wiring (before starting this stage of work, it is recommended to photograph the connectors);
• inspection of the part for defects;
• installation of a new board in case of breakdown.

Checking the filling system

Slow water intake indicates a clogged filling system. Check this part of the dishwasher as follows:

• turn off the water supply tap;
• disconnect the drain hose from the device body, the second end of the flexible tube is disconnected from the water supply;
• the hose is washed with a stream of water;
• remove and inspect the strainer located in front of the inlet valve;
• the filter is cleaned of contaminants;
• assess the condition of the intake valve (if there is no blockage, check the electronic parts with an ohmmeter; if faulty, replace the valve).

Another reason for lack of water supply is a clogged detergent dispenser. The powder absorbs moisture and forms a dense layer, so after each wash the trays must be wiped with a napkin. It is also necessary to check whether the injectors are clogged. The blade is removed by removing the screws. The holes are cleaned with a toothpick and washed with water.

Dishwasher does not drain water

When the machine does not drain water, but you can hear the engine humming, this may indicate that the pump is blocked by small pieces of food passing through the filter cylinder. In this case, pumping out water will be impossible, and this will lead to the program stopping.

To unlock the pump, follow these steps:

On some models, the pump cover is removed using a hex screwdriver (asterisk), and after cleaning, everything is reassembled in the same way.

Another reason for the breakdown may be a burnt-out motor winding. The electric motor windings are checked using a multimeter for short circuits or breaks, after first disconnecting the motor from all wires. If damage is detected, the coil can be rewound by contacting specialists, or the motor can be replaced with a new one.

Main causes of breakdowns

It is not difficult to identify a malfunction; you just need to analyze the signs of a breakdown. The machine may not turn on or display an error code. The most common malfunctions that occur are:

• Burnout of heating element. Leads to a decrease in the quality of dishwashing. The device stops heating water. In this case, you should check the condition of the wires and the heater itself. Less often, breakdowns occur in the electronic module responsible for heating the water.
• The appearance of extraneous sounds. This happens when the bearing wears out. The part fails due to leaching of the lubricant and thinning of the oil seal. In this case, disassemble the pump and replace the bearing. Noise may also occur due to glass fragments getting into the pump impeller.
• Lack of water supply. The reason lies in the clogging of the elements of the fill system. All parts need to be inspected and cleaned.
• Water leak. The reason is wear or displacement of the seal. The car tank leaks less often. The device will have to be disassembled and the damaged part replaced.
• No drain. Observed when the drain pump, hose or filter is clogged.

PMM error codes on BIT100 and DIWA boards

The listed control modules are installed on dishwasher models Indesit D 41/42, DC 27, DI 45/450/460, IDE 100/1000/1005/44/45, IDL 40/410/411/42/420, IDL 557, IDL 70/7021/710.

In general, the display of error codes by LEDs on Indesit PPM models with BIT100 and DIWA control modules repeats the indication on models with DEA ​​601/602/700 boards with two exceptions:

An example of displaying error code AL05 on an Indesit PMM with a BIT100 board

In the table below, for those error codes that generally coincide with similar errors for DEA 601/602/700 boards, instead of repeating a detailed description, links to the previous table will be provided. But keep in mind that in operating mode, only errors AL06 (“Water tap closed”), AL05 (“Filters clogged”) and AL02 (“Fill valve faulty”) are available to users.

Code 4 indicators 6 indicators Description / Remedy

CONTROL PANEL WITH INDICATORS

The photo shows numerous examples of the design of control panels for Indesit dishwashers without a display, with 4 or 6 indicators (LEDs).

PMM Indesit control panels with 4/6 LEDs

Control panel of the built-in Indesit PMM with 6 LEDs

Options for Indesit PMM control panels with 4 LEDs

What to do if an error code appears on the screen?

The Indesit dishwasher is considered a successful household appliance. Certain error codes can be eliminated with your own hands without disassembling the unit. Experts advise restarting the machine three times. If the code returns again, you will have to disassemble the dishwasher and perform diagnostics using the decoding of the code meanings. How to reset the dishwasher:

If the error code does not appear on the display screen, the dishwasher can be used as usual. Otherwise, the reboot should be repeated a couple more times. The worst case scenario is that the error persists and the unit has to be disassembled.

No water heating

This fact can be attributed to the main and most common malfunctions of dishwashers. The water may not heat up for the following reasons:

The first fault is easily determined using a resistance tester. If a break is detected, the heating element is purchased and replaced with a new one. If you suspect that the problem may be caused by the second and third malfunctions, you need to disassemble the PMM, and this cannot be done without the help of a specialist. For example, to check the timer, you need to know the algorithm for turning on the contacts for heating the heating element.

Control panels with indicators

The photo shows numerous examples of the design of control panels for Indesit dishwashers without a display, with 4 or 6 indicators (LEDs).

PMM Indesit control panels with 4/6 LEDs

Control panel of the built-in Indesit PMM with 6 LEDs

Options for Indesit PMM control panels with 4 LEDs

Dishwasher does not wash dishes well

The water supply blades can also become contaminated with food debris, which has a bad effect on the operation of the machine. You can disconnect the upper blade by simply unscrewing it, and the lower blade by easily pulling it up.

Check the holes through which the water flows and clean them (if necessary) using a regular toothpick. After cleaning, the blades must be put back in place.

The most common causes of dishwasher malfunction were considered. Of course, it is impossible to describe all the reasons, but by following this algorithm, you can quickly determine the location of the breakdown and, if it is within your power, begin repairing the unit with your own hands.

We care about our customers and try to provide service...

• Image
• Text

+15

We care about our customers and try to provide the best service possible.

quality. We are constantly improving our products to make your communication with

technology is simple and pleasant.

Equipment care

Extend the service life and reduce the likelihood of equipment breakdowns.

Use professional equipment care products from Indesit Professional for the most

simple, effective and easy care of your household appliances.

Indesit Professional products are manufactured in Italy to the highest European standards

areas of quality, ecology and safety of use and are created taking into account many years of experience

equipment manufacturer. Find out more on the website www.indesit.ru in the “Service” section and ask at

stores in your city.

Authorized service centers

To be closer to our consumers, we have created a wide service network, the peculiarity of which is

is the high training, professionalism and honesty of service technicians. To date

it has about 350 service centers in Russia and the CIS.

You can find their contacts in the service certificate and on the website www.indesit.ru in the “Service” section.

If you need to contact the service center:

Attention! When making repairs, require the use of original spare parts. Before contacting the Technical Service:

Before contacting the Technical Service:

Check whether you can fix the problem yourself (see Malfunctions and troubleshooting methods).

Run the program again to check the machine's health.

Otherwise, contact an authorized Technical Service Center.

Never contact unauthorized technicians.

When contacting Technical Service, please inform:

nature of the malfunction

product model (Mod.)

serial number (S/N)

You will find this data on the rating plate located on the product.

(see Product Description).

You can find other useful information and news on the website www.indesit.ru in the “Service” section.

Comments

Select → I found the instructions for my dishwasher here! #manualza

Click →

If you follow all the instructions, you will have no time to live.

Manualza!manualza.ru

What to do if an error code appears on the screen?

The Indesit dishwasher is considered a successful household appliance. Certain error codes can be eliminated with your own hands without disassembling the unit. Experts advise restarting the machine three times. If the code returns again, you will have to disassemble the dishwasher and perform diagnostics using the decoding of the code meanings. How to reset the dishwasher:

If the error code does not appear on the display screen, the dishwasher can be used as usual. Otherwise, the reboot should be repeated a couple more times. The worst case scenario is that the error persists and the unit has to be disassembled.

Source