Recommendations for connecting a Bosch washing machine to communications

Preparation

It is recommended to start preparing for installation by studying the instructions from the manufacturer , which comes with the Bosch washing machine. The device is taken out of the packaging and the completeness of the package is checked.

Tools

The required set of tools is determined by what work will have to be performed and whether all communications are connected. If everything is ready for installation, then you only need to worry about having a set of keys and the building level.

Transport bolts

After the Bosch washing machine has been unpacked and its place in the apartment has been determined, you need to remove the shipping bolts . They are installed on the rear wall and are designed to stabilize the position of the tank during transportation. Usually there are 4 of them.

It is prohibited to use a Bosch washing machine with the transport bolts not removed. In place of the removed bolts, plugs are inserted, which come with the device.

After the shipping bolts have been removed, they must be saved along with the documents for the washing machine, since they may still be needed if the machine needs to be transported.

You can clearly see how to remove Bosch transport bolts in the video:

Transport bolts

The bolts are installed at the rear of the Bosch SMA housing. They stabilize the position of the tank and prevent it from moving when transporting equipment. There are usually 4 transport bolts in the washing machine - they must be removed before operating the unit. Using equipment with installed bolts is strictly prohibited. After removal, plugs are installed in their place, which are supplied with the unit. The bolts and operating instructions for the SMA must be kept. In the future, for example, when moving, the transport bolts are installed again.

Selecting a location

It is advisable to select a place to install a Bosch washing machine in advance. The following points need to be taken into account:

• compliance of the dimensions of the washing machine with the available free space;
• proximity to utilities (electricity, water, sewerage);
• ease of use of the device.

The optimal places to locate a Bosch washing machine are: a kitchen, a bathroom, possibly a pantry, a hallway or a utility room.

In rare cases, washing machines can even be installed in living rooms, if other options cannot be implemented, for example, in dormitories or hotel-type housing.

The room chosen for installing a Bosch washing machine must have good ventilation and a flat floor (optimally concrete or non-slip tiles) .

If the room is always humid, this will negatively affect the equipment due to corrosion and poor drying of the drum and tank between washes. Because of this, mold and an unpleasant odor may appear on the cuff and in the tank. Despite the fact that the space for the washing machine should be taken care of in advance, if necessary, the device can be rearranged.

Instructions for replacing aquastop

Find out your device type

If it is mechanical, then it is enough to simply “snap” it back. The spring will return to its original position. If it is absorbent, then the absorbent material will soon return to its original position, you need to wait. The electromechanical one needs to be replaced, so read the material further.

This will not give you the opportunity to receive a current discharge, and will also give you access to the electromechanical aquastop.

This must be done, because without aquastop, a leak is likely!

It just rolls up, nothing complicated.

Do it carefully, don't break it! In the photo it is the blue wire.

Reassemble the new device by following the steps in reverse order.

Be sure to repeat the sequence exactly. This will protect the new device from damage.

You have replaced the aquastop on your dishwasher!

If you need spare parts for self-repair, purchase them from us: the widest range, fast delivery throughout Russia and a guarantee on everything.

Modern housewives are happy to use various household appliances that facilitate the process of cooking and doing household chores. One such device is a dishwasher.

For the normal functioning of the unit, it is important to have the correct connection to the water supply, sewerage and electrical networks. To provide the car with water, experts advise using an Aquastop hose

What it is? And what role does this element play in the functioning of the dishwasher?

How to connect a Bosch washing machine?

Instructions for connecting a Bosch washing machine to communications:

To electricity

The Bosch washing machine must be connected through a separate socket with an output to the machine . The use of extension cords and tees is highly discouraged.

When discharging electricity into the bathtub, special sockets should be installed that are protected from moisture. The outlet must also be grounded.

The electrical cord leading from the washing machine must reach the outlet freely and not be pulled tight.

To water supply

The Bosch washing machine should be connected to cold water. You can arrange the pipe wiring yourself or by calling a plumber . He will install an adapter with a tap to connect the inlet hose of the washing machine. This hose is included with the washing machine, but can be purchased separately.

The Bosch inlet hose has two ends that are organized differently. The one with a bend and a plastic nut is mounted on the washing machine. No special tools are required to secure it; the nut can be easily tightened simply by hand. The second end of the hose is connected to the water supply.

It is advisable to organize the tap into the water pipe in an accessible place so that it is convenient to open and close the tap that supplies water to the device.

To the sewer

Connecting a Bosch washing machine can be done by directly tapping into the drain pipe, through a siphon under the sink, or by throwing the free end of the hose into the bathtub or sink. The last option is inferior to the others in aesthetics and convenience, so it can be considered more as temporary.

If a drain insert from a Bosch machine is made directly into a sewer pipe, the hose must be inserted through the cuff. This will allow it to be fixed and prevent unpleasant odors from drains from entering the apartment.

The Bosch drain hose must be located freely, without kinks or being crushed by furniture . It is important to ensure that it is raised above the level of the tank, according to the manufacturer’s recommendations. Such installation will prevent self-draining from the washing machine and prevent unpleasant odors from the sewer from entering the apartment.

If the drain hose in the device is located in the upper part of the body, it means that the necessary lift is inside the washing machine, and there is no need to organize anything additional about this.

You can see what such a system looks like in the video:

The dishwasher is constantly draining water - what should I do?

Additional symptoms of trouble

You can also make sure that you are really dealing with just such a problem by the following signs:

• The noise of water gathering and a running pump is heard all the time;
• Rebooting the machine, that is, temporarily disconnecting it from the network, does not in any way affect the change in the situation;
• The device does not respond in any way to pressing any keys;
• An error code appears on the display.

If all of the above points can be applied to your case, then when you contact the service center, you can immediately voice the problem you are having: the dishwasher is constantly draining water. This way, it will be much easier for dishwasher repair technicians to understand what kind of malfunction may have happened to your assistant and prepare in absentia for future treatment.

Causes of malfunctions and ways to eliminate them

1. The AquaStop system sensor is stuck or flooded with water. Sometimes tilting the device on its side, about 45 degrees, helps correct the situation. Then the water comes out of the sensor on its own and when the machine is restarted, everything returns to normal.
   Another reason for the Aquastop system to operate is a leak in the device tank. True, the owner of the equipment is unlikely to be able to independently verify the correctness of his suspicions, much less replace the part. The procedure for removing and replacing the tank is too complicated.

   It can only be performed by a specialist who has all the tools and equipment necessary to perform such an operation.

2. Failed inlet valve. Typically it receives a command to allow a certain amount of water into the system and then closes. If damaged, it may become stuck in the open position.
   Water will flow freely, an overflow will occur, the pump will turn on and pump out excess liquid. And so on in a circle... The problem that has arisen should be resolved immediately. To do this, you must immediately shut off the water supply to the device.

   After waiting until the pump has pumped out all the liquid, unplug the cord from the outlet and urgently call service center workers to repair or replace the inlet valve.

3. Broken pressure switch.
   The water level sensor signals to the control module that there is a sufficient amount of liquid collected. If it breaks down, no such signals are received and water is collected non-stop. The part needs to be replaced with a new high-quality spare part.
4. Control board faulty.
   Or rather, the control triac of the drain pump has failed. It is “stuck” and gives commands to constantly pump out water (even if it does not enter the device). Sometimes the issue can be resolved by resoldering the triac contacts on the control board, or it is necessary to completely change the spare part.

Note! It is strictly not recommended to try to independently repair such a complex piece of equipment as a dishwasher without the proper experience and tools. Such “home experiments” most often end in a long and expensive resuscitation of the household appliance by specialists, and in the worst case, the need to purchase new equipment. Don’t waste your time and energy - if you notice the first symptoms of a problem, immediately seek help from specialists

Don’t waste your time and energy - if you notice the first symptoms of a problem, immediately seek help from specialists

Such “home experiments” most often end in a long and expensive resuscitation of the household appliance by specialists, and in the worst case, the need to purchase new equipment. Don’t waste your time and energy in vain - if you notice the first symptoms of a problem, immediately seek help from specialists.

How to place an urgent call for a technician?

You can call a service employee for a call right now:

We will contact you immediately and clarify all related questions. Within a few hours after completing the application, our specialist will arrive at the door of your home.

He will quickly and professionally diagnose the device (the service is free, subject to further repairs by us), determine the cause of the breakdown and tell you the options and cost of eliminating it.

After agreeing on all the issues and approving the estimate, he will immediately begin to “treat” the equipment.

For us, employees, there are no unsolvable tasks and problems in the field of repairing household appliances. Contact us and today you can see for yourself!

Setup and first launch

Setting up a Bosch washing machine begins with leveling it. To carry out the work, a building level should be placed on top of the washing machine body and, using it as a guide, tighten the legs on the machine. It is important to control the stable position of the washing machine.

You can check the correct installation by trying to swing the device by the corners. If the machine wobbles, the legs need to be tightened further.

The first start of Bosch must be controlled without leaving the machine. To get the technique started, you need to act sequentially:

1. 
   Plug the electrical cord into an outlet.

2. Open the water supply tap to the washing machine.
3. Check the position of the drain hose.
4. Pour detergent into the powder receptacle.
5. Select a washing program with additional rinsing, heating the water to 40-60°C and a cycle duration of at least an hour. This will allow you to thoroughly rinse the inside of the washing machine from technical oils and dust.
6. Check that the drum is empty - without laundry and without foreign objects.
7. Close the hatch door.
8. Start the wash cycle.

To start the device for the first time, it is advisable to choose a special tool that is intended directly for the first start.

Restoring working condition

The advantage of mechanical protection is that it can be used repeatedly. After eliminating the cause and consequences of the leak, it is enough to cock the spring until it clicks and the device is ready for use. Alternative options will require replacing the hose. The procedure is simple and takes a few minutes. Necessary:

1. Shut off the water supply.
2. Remove the used hose with casing.
3. Screw on a new one.

With Aquastop, the leak will almost always be eliminated. However, its small probability still exists. To prevent a leak from becoming an unpleasant surprise, regularly inspect the dishwasher and the area around it for leakage.

A Bosch dishwasher can significantly simplify modern life, eliminating the need to wash dishes yourself, spending a lot of time on this, which can be used much more rationally.

It is important to remember that the use of any Bosch household appliances requires compliance with some basic rules, thanks to which the devices will serve their owners longer without requiring repairs. They are usually written down in the instructions.

Particular attention should be paid to the installation and connection of the dishwasher, since not only the ease of use of it depends on this, but also the safety when it is in operation. The Aquastop system, which is often found in modern household appliances connected to water, serves to protect against leaks

The Aquastop system, which is often found in modern household appliances connected to water, serves to protect against leaks.

Possible problems and ways to solve them

When installing a new Bosch washing machine or one brought from another apartment, you can often encounter unforeseen situations and unexpected problems. In most cases, solving them is not difficult:

Stage #3 – leveling the washing machine

In order for the automatic machine to serve with maximum efficiency, the installation and connection of the washing machine should be approached with the utmost care.

The floor base requires special attention, which must meet a number of criteria:

• strictly horizontal surface;
• durable structure;
• sustainability;
• protection from vibration and other influences inevitable during operation of the unit.

If the foundation does not meet these criteria, it is better to take measures to meet them.

In addition to levelness and reliability, the base for installing the washing machine must also have anti-vibration properties. If you are going to install it on a tiled or wooden floor, then it is better to carry out the whole process using devices that dampen vibration:

Image gallery

Photo from

Felt pieces against vibration

Anti-vibration stand for washing machine

Round anti-vibration device

Invisible anti-vibration pads

On fragile surfaces, it is advisable to make a cement-sand screed or strengthen the existing floors in the place where the washing device is supposed to be installed.

Adjustment of the position of the washing unit is achieved by changing the height of the support legs: to increase the distance from the floor they can be unscrewed, and to decrease they can be screwed in

After making sure that the base meets all the previously mentioned requirements, you can begin installation. The fully unpacked machine with the fasteners removed is placed in the selected location.

The horizontal installation is determined by the top panel, while the angle of deviation, which is checked by the top cover, should not exceed two degrees. Exceeding this indicator leads to a sharp increase in vibration, which has a very negative effect on the condition of the components and significantly reduces the service life of the machine.

Image gallery

Photo from

Step 1: Screwing all legs to minimum height

Step 2: Adjust the rear support to the required level

Step 3: Checking the horizontal alignment of the legs

Step 4: Fine Adjustment of Support Heights

Placing improvised materials under them that could slip out from under the supports during work is strictly prohibited. This may lead to an emergency situation. At the same time, it is allowed (and even recommended) to place a thin rubber mat on the sliding tiled surface.

As soon as the body of the machine is in a perfectly horizontal position, you should tighten the locknuts counterclockwise, fixing the optimal height of the support legs.

When leveling the machine, it is recommended to consider the following factors:

1. The greatest degree of stability of the unit is achieved with the adjusting supports screwed in as much as possible, but this option is only permissible on a perfectly flat surface.
2. When installing the machine on an inclined floor, it is advisable to use fixing parts to secure the supporting structures.
3. To check whether the unit is installed correctly, you need to try to swing it diagonally. If the process is done correctly, there is no free play or its amplitude is the same for different diagonals.

Once you are sure that the unit is in the correct position, you can proceed to the next steps.

Call the master

If you cannot connect a Bosch washing machine yourself, you must use the services of a specialist.

You can find a company on the Internet. It is better to trust companies that have been operating in the service market for a long time and have a reliable reputation.

The price list of individual companies may have significant differences, and it is better to clarify such information with the company’s dispatcher. The cost of work depends on the volume and complexity.

If all communications have already been removed, then a master in the capital can charge from 1000 rubles . Installing a built-in washing machine will cost more (from 1,500 rubles).

In the case where communications are not installed and preparatory measures are required, the cost of the work increases significantly - up to several thousand. Additional details, if they are needed when performing work, are paid for separately by the customer.

When calling a technician, you should indicate the manufacturer of the washing machine, the model of the device and whether communications are connected.

Customer Reviews

Leonid

5

Thank you for arriving quickly! In other companies you don’t even get along normally with the foreman; you have to adjust your time to him. Denis got the hang of it and arrived on the same day we called him. I solved the wiring problem and now everything is fine. 02/28/2022

Master: Mitinkov Denis Eduardovich

Olga

5

Thanks for the work. The repairman installed new ventilation grilles, replaced the heating radiator in the living room and installed a new hob to replace the broken one. The whole complex turned out cheaper than I thought. 02/24/2022

Master: Semenov Andrey Valentinovich

Maksim

5

I believe that a home handyman should come, quickly assess the situation and find a solution to the problem. Valery is just such a person. He performed the calculations on the spot and hung the hood in the prepared area. Inexpensive and efficient. 02/13/2022

Master: Grishkovets Valery Petrovich

All reviews

Recommendations

When installing a Bosch washing machine, the following recommendations may be useful:

1. If tap water is not of adequate quality, it is advisable to install a filter to purify it at the entrance to the apartment. This will prevent foreign particles from entering the washer.
2. When tapping into a water supply system to draw water to the machine, it is necessary to provide for the installation of a tap that shuts off the water.
3. When starting up the washing machine for the first time, you should not put things in the drum, as they may become dirty after processing due to the fact that the new washing machine contains grease and other technical liquids that remain after the production and assembly of the device.

Self-installation

Replacing an old hose is not a difficult job - we turn off the water and dismantle the hose, and install a new one in its place. If you used a system with a solenoid valve, then you need to carefully connect the wire with the plug to the sensor, which is located next to the filler inlet on the machine.

Any system is quite effective and protects your household appliances from various leaks and troubles that end in a flood. It’s not for nothing that experts advise installing Aquastop protection systems; they work simply - any user who does not have any technical knowledge can carry out the replacement.

What is Aquastop

AquaStop is the general name for a system for protecting household appliances from water leakage. Different manufacturers have different names for it: Aqua-Stop, Aqua-Alarm, Waterproof, Aqua-Safe.

The system looks like a regular hose in a protective casing with a valve that shuts off the water supply in case of rupture, leakage, cracks in the hose, or wear of the seal. The main function is to protect housing from flooding. It is installed on washing machines and dishwashers.

Is it possible to do without Aquastop in household appliances? It's possible, but it's not safe. Excessive pressure and water hammer in the water supply system are common occurrences. The consequences can be dire for both the apartment owner and his neighbors.

Useful tips

If you want to reduce your electricity consumption, you need to follow these helpful tips.

• Do not machine wash items that are only suitable for hand washing. Information about this can be easily found on product labels;
• It is forbidden to overload the device more than intended (information about this must first be obtained from the instructions and followed).
• It is important to prevent metal parts from getting into the device - they can damage the drum and the clothes themselves.

During the first use, it is advisable to pour into the device a special product intended for the first machine washing of clothes. It is taken in small quantities, less than is usually required.

The product for the first launch is sold in specialized stores. For example, you can purchase Helfer Start. This composition is suitable for almost any model of newly purchased cars.

Finally, here are some tips on how to properly wash your clothes. It is necessary to wash white, black, and colored clothes separately. Then light things will not be painted in other colors.

You should take no more than 100 g of powder for each wash. It must be intended by the manufacturer specifically for automatic machines.

Before washing, do not forget to remove all small items from the pockets of your clothes. Between washes, it is better to leave the hatch of the device slightly open. As a result, moisture from the drum will evaporate freely. Otherwise, a bad odor and even mold may appear inside the device.

You should not overload the device or overfill the tank with laundry, so that the parts do not fail faster than expected. A special sensor, which is now often equipped with modern device models, will indicate if the tank is overloaded. The equipment is quite capable of breaking even if the tank is slightly underloaded. So it is important to pay primary attention to this when using technology.

If you follow all these rules, the washing machine will last quite a long time and will significantly save valuable time, which is usually spent by housewives on hand washing. The machine will allow you to wash clothes made from cotton and linen fabrics, various laundry, including delicates, and outerwear.

We suggest you familiarize yourself with How to clean white gold at home