Malfunctions and error codes of the Indesit washing machine: interpretation and repair methods

Indesit with electronic control differ in the way they indicate faults and failures. Washing machines of the Wisl (82, 102), Iwsb5105, W105tx series, with EVO-I, II, Arcadia, LOW END modules do not have a display - Indesit error codes are identified by flashing signal lights . The symbolism does not indicate a specific unit or part, but it gives direction for searching for a problem - it becomes possible to fix the problem yourself.

On a note

• The lack of light on the indicators does not necessarily indicate a malfunction of the Indesit. As a rule, the failure is caused by the supply voltage (mismatch of the U value of the network, periodic surges, power outage).
• When the lights flash and light up at the same time, troubleshooting begins with testing the switching power supply of the Indesit washing machine. Its incorrect operation is the root cause of problems that arise.
• If Indesit malfunctions or errors appear, you need to reboot the electronics of the washing machine : remove the voltage (for 15 minutes) and turn it on again. If the problem is caused by a power supply problem, the code will clear.

What Indesit error codes exist and what should I do?

The main errors issued by Indesit have values ​​from F01 to F18, as well as H2O. However, there are exceptions to consider:

• F16 is typical exclusively for top-loading washing machines,
• F13-15 are not available on Indesit machines that do not have a drying function.

When a breakdown occurs, the code of which is displayed on the display or recognized by the number of blinks, the door is locked. Indesit error codes can signal both technical problems and incorrect inputs (exceeding the permissible load limit, for example). The Indesit washing machine can generate an error both at startup and during operation (when switching to rinsing or spinning, if a functional discrepancy is detected).

Fault prevention

For preventive purposes, adhere to the following rules:

• provide protection from high humidity;
• provide protection against voltage surges by installing a machine;
• do not allow excessive load;
• It is recommended to fasten metal fasteners and buttons before washing.

It is not advisable to disassemble the Indesit SM and repair it yourself if the warranty period is still valid and the damage is minor. Warranty service is carried out in the workshop free of charge. In case of severe damage, consumers can contact a service center.

F04

Code F04 indicates that the pressure switch readings are incorrect. The water may be turned off, the shut-off valve is not open, there are blockages in the inlet filter, or the pressure switch is broken.

What is the right thing to do?

• Check the water, open the shut-off valve.
• Remove the blockage in the filter.
• Inspect the pressure switch, clean the tubes, and if it is seriously damaged, replace it.

If the washing machine is an old model, the error will be reflected by blinking button 2.

How to prevent breakdowns in the future?

In order for your washing machine to last as long as possible without breakdowns, you need to take proper care of it.

Basic recommendations:

1. Monitor the integrity of hoses and cables.
2. Avoid getting moisture on parts.
3. Clean the powder receptacle regularly.
4. Remove moisture from the cuff.
5. Protect the device from power surges by using a power adapter.
6. Stop washing if the water pressure drops or if there is a power surge.

F05

Does the Indesit washing machine show code F05? Problems with the drain pump! There may be several reasons:

• broken pump, faulty wiring,
• the drain system is clogged,
• The pressure switch is broken.

What will you need?

• diagnostics, restoration of damaged wiring sections.
• eliminating blockages in the pump or filter located behind the hatch.
• It wouldn't hurt to inspect the pump impeller.
• in a critical situation, a new pressure switch will be needed.

“Indesit” without a display in the event of such a breakdown shows the book. 2.4.

Call the master

Even if you managed to decipher the error yourself, it is not always possible to eliminate it on your own. Lack of experience in repairing household appliances or a serious breakdown is a reason to contact a specialist. The cost of repairs depends on what exactly is broken in the equipment.

Approximate prices for some types of work:

• F02 - engine repair or replacement will cost 2,000 rubles;
• F05 - replacing the drain pump costs from 1,600 rubles;
• F08 - replacing the heating element will cost at least 1,400 rubles;
• F07 - replacing the pressure switch will cost 1,600 rubles;
• F17 - replacing the UBL costs about 1,300 rubles.

Finding a washing machine repairman is not difficult. The market is full of such offers. There are many advertisements on the Internet and in the print press in which specialists offer their services. You can also contact a specialized center.

To minimize the risk of encountering scammers, you need to pay for the service only upon its provision . Before calling a specialist to your home, you need to find out how much it will cost. Most often, technicians do not charge money for diagnostics if the client agrees to repairs.

The maximum cost of a paid call should not exceed 400 rubles. It’s good if the selected specialist has positive reviews from other clients, not on the service’s website, but on other sites.

F06

The error is due to problems in the control system. There may be three reasons:

• The controller controlling the panel has failed,
• the contacts between the board and the controller are broken,
• The main module is inoperative.

What to do?

• First of all, you need to diagnose in which of the listed sectors the failure occurred.
• Repair or replacement of unsuitable parts.

The error on the buttons will be indicated by flashing 2,3.

Malfunctions and self-testing of washing machines with Arcadia control module

To activate the autotest procedure, you must complete the following steps; in this case, in the initial position, the program selection knob (program selector) is in the uppermost position (12 o’clock):

• turn on the machine and turn the program selector clockwise one position. Turn off the machine and return the program selector to its original position
• turn on the machine and turn the program selector clockwise two positions. Turn off the machine and return the program selector to its original position
• turn on the machine, turn the program selector counterclockwise one position, then press the “Start” key.

Rice.
1 Control panel
Note:

At the end of the auto test or after it is interrupted, turn off and turn on the machine again using the On/Off key.

Fault indication

Fault indication is carried out in binary code, each digit of which corresponds to one of the LEDs, in order from right to left (see table below)

Rice.
2 LEDs for indicating error codes
Table 1
Indicating error codes

Fault table for Arcadia machines

• The fault table for Arcadia is different from the fault table for EVO II
• Attention:
  in case of faults other than
  F01
  , the board should be replaced only after all other checks have been completed

• Check for any water leaks that could enter connectors J006
  and/or
  J009
  and close the corresponding contacts;
• Check for traces of water on the board and connector J001
  ;
• Check the wires connecting connector J006
  to the pressure switch;
• Check the pressure switch terminals (a short circuit may occur as a result of exposure to chemical residues from the production process);
• Check the motor terminals (a short circuit may occur as a result of exposure to chemical residues from the production process);
• Check the heating element terminals;
• Check the contacts of connector J004
  on the board;
• Measure
  the resistance of the pump motor winding J004
  (pins
  4
  and
  5 it should be equal to 170 Ohm +/- 10%;
• Check the wires connecting connector J004
  (pins
  4
  and
  5
  ) to the drain pump;
• Replace pressure switch
• Replace the drain pump
• Replace the board.

• Check if the engine is blocked;
• Check the contacts of connector J009
  on the board;
• Check the tachogenerator winding: at connector J009
  , the resistance between pins
  1
  and
  2
  should be in the range from 115 to 170 Ohms.
  In case of an open or short circuit, ring pins 1
  and
  2
  on connector
  J009
  corresponding to the tachogenerator
• Replace the engine;
• Replace the board.

• Check the contacts of connector J005
  on the board;
• 
  the resistance between pins
  1
  and
  2
  at connector J005 ;
  at an ambient temperature of 20°C, the sensor resistance should be approximately 20 kOhm; If the value is incorrect, ring the wires connecting connector J005
  (pins
  1
  and
  2
  ) to the NTC sensor.
• Measure the resistance directly at the NTC sensor; it should be 20 kOhm at ambient temperature (20°C);
• Replace NTC sensor;
• Replace the board.

• Check the contacts of connector J006
  on the board;
• Ring the wires connecting connector J006
  to the pressure switch;
• Measure
  the resistance of the pump motor winding J004
  (pins
  4
  and
  5 it should be equal to 170 Ohm +/- 10%;
• Check connecting wires and connectors J004
  /pump;
• Check pump filter + drain
• Replace the pump;
• Replace the board.

• Check for any water leaks that could enter connector J004
  and close the corresponding contacts;
• Check the terminals of the door lock device (short circuit may occur due to exposure to chemical residues from the manufacturing process)
• Check the connecting wires and connectors J004
  / door lock;
• Check the door locking device;
• Replace the door lock device;
• Replace the board.

• Check the contacts of connector J001
  on the board;
• Ring
  contacts
  3
  and
  4
  J001 , corresponding to the washing heating element. A heating element with a power of 1800 W with a rated voltage of 230 V has a resistance of 25 Ohms +/- 10%. If the measurement does not show this value, the washing heating element should be replaced;
• Replace the board

• Check the contacts of connector J001
  on the board;
• Check the resistance between both ends, it should be at least 30 ohms; The resistance to the body must be more than 1 mOhm
• Replace the heating element;
• Replace the board.

• — Remove the plug from the socket, wait 2 minutes, then reapply power and test the machine again.
• If the problem remains:
• — Reprogram the main board
• — Replace the main board;
• — Replace the display board.

• Check the contacts of connector J004
  on the board;
• Measure
  the resistance of the pump motor winding J004
  (pins
  4
  and
  5 it should be equal to 170 Ohm +/- 10%;
• Check connecting wires and connectors J004
  /Hacoc;
• Replace the pump;
• Replace the board.

• Check the contacts of connector J010
  on the main board;
• Check the connector pins on the display board
• Ring the wires connecting connector J010
  to the display board
• Unplug, wait 2 minutes, then reapply power and test the machine again.

If the fault persists, proceed as follows:

Fault table for Arcadia machines with subcodes

Fault subcodes can only be “seen” in the microprocessor’s memory, so they can only be displayed when using a pocket computer and Doctor programs.

F10

The pressure switch stopped giving signals. There may be several reasons for this error:

• no water is supplied, the water supply valve is closed,
• blockages in the drainage system,
• The water sensor level is acting up.

You can also repair it yourself:

• just check the water supply or open the valve,
• clean the drain system, inspect the intake valve,
• The sensor may be broken and will have to be replaced.

An old-style washing machine will blink with buttons 1 and 3.

H2O

The code indicates a blockage in the drain system sector or the washing machine is not connected correctly. There are two options to solve the problem: cleaning the drain system or reconnecting the machine.

Thanks to the achievements of modern electronics, using the display provided by the Indesit washing machine, you can accurately determine the cause of a technical malfunction or inconsistency of input data. If the Indesit washing machine displays an error related to a malfunction of the control module, it is better to entrust the diagnostics and repairs to a specialist so as not to aggravate the situation.

Other reasons for program crashes and blinking indicators

The LEDs on the control panel may blink not only due to a breakdown, but also due to incorrectly set parameters. There are a number of washing modes that provide the ability to connect additional functions:

• additional rinse
• higher degree of water heating,
• ironing

Instead of turning on, the indicator may flash if the selected program cycle does not provide a particular function.

The machine can generate a service error both at the initial stage of washing and during it. In cases where the weight of the load of laundry is not comparable to the number of revolutions or the maximum allowable volume of laundry provided for by the technical specifications, the spin process may not start. In this case, the buttons indicating a failure in the “Rinse” and “Spin” modes and the door lock indicator will start flashing. At this moment, it is necessary to restart the machine a second time, reducing the number of things.

To be able to restart or change the program mode, simply press and hold the start button.

After this, the execution of the specified program will stop. After a few seconds, the door will unlock, allowing you to make adjustments and start washing.