c) the pressure when water enters is less than 1 bar.
3. It is possible to start the program again.
d) malfunction of the water level controller.
d) lime deposits on the heating element or a malfunction of the heating element.
c) heating occurs during a period when there should not be heating.
Source of the article: https://stiralmashinyinfo.ru/oshibki/oshibka-e23-v-stiralnoj-mashine-siemens/
Error codes for Siemens washing machines: F21, E18 and E23, F23 and F18, E17, E21 and others, Siemens washing machine error e23 how to fix.
Siemens washing machine error codes: description, causes and fault reset
Siemens washing machines are distinguished by their reliability and high build quality. The manufacturer has taken care of a high-quality self-diagnosis system.
If household appliances break down, it is quite easy to find out the reason. An error code will appear on the display, which will indicate a problem.
Elimination
Actions must be taken based on the malfunction. For example, if fault F04 is displayed, then you need to find and fix the leak. If you need to unlock the control panel to solve the problem, you can restart the washing machine.
It is important to first turn off the power using the button, then unplug the power cord from the outlet.
Troubleshooting common errors:
It is highly not recommended to fix critical errors yourself. Incompetent repairs can lead to the equipment becoming completely inoperable.
You should immediately contact the service center and call a technician. You can only deal with typical, minor breakdowns on your own.
Let's check the level sensor
Often, to solve the E18 problem, it is necessary to repair the breakdown of the pressure switch. Doing this yourself is not difficult. The main thing is not to forget about safety precautions and disconnect the machine from all communications. Then we begin checking the functionality of the water level sensor:
We finish testing with a visual inspection. We probe the tubules for blockages, and examine the device itself for integrity. If clogged, wash the holes with a stream of water, and if damaged, change the pressure switch.
There is another, more reliable way to check the water level sensor - ring it with a multimeter. We set up the device in resistance measurement mode, attach the probes to the contacts and evaluate the result on the display. Fluctuating numbers indicate that the pressure switch is fully functioning, and the absence of changes indicates its malfunction. The situation cannot be corrected by repair - a complete replacement is necessary.
If both the pumping system and the pressure switch pass the test, then the problem is in the control module. It is strongly not recommended to do DIY repairs with the electronics of the washing machine: there is a high risk of aggravating the situation. It is better to stop the diagnosis and contact a service center.
Adviсe
Siemens washing machines are reliable and have a long service life. The equipment will work flawlessly with proper care.
Here are some basic tips.
To learn how to resolve error F23, watch the video.
Source of the article: https://stroy-podskazka.ru/stiralnye-mashiny/neispravnosti-i-remont/kody-oshibok-siemens/
Error F21 in a Siemens washing machine - what to do, Siemens washing machine error e23 how to fix it.
We repair equipment with our own hands
Now consider the case when water actually forms in the pan. It is important to keep in mind that in this case you need to look for exactly the reason for the liquid getting into the pan, and not pump out the water and hope that the error will disappear. Although first, indeed, the water will need to be removed (some do this with an enema, some by tilting the body, the methods are very diverse).
Once there is no more water left in the pan, the washing unit must be disassembled to check the most susceptible components for leaks. Among them:
- pipes, hoses, as well as their connections with other parts;
- drain pump;
- powder container;
- tank.
If a crack or hole is found in one of the parts, you can fix the damage by covering the hole with cold welding or sealant. However, experienced craftsmen prefer and recommend that users change the entire part, as this is a more reliable way to stop the hassle. After all, perhaps in two days a crack will form in another place and then the repair will have to be repeated.
On the other hand, due to a tiny crack, replacing the entire tank is very troublesome and costly. Therefore, it's up to you to decide. Each user has his own view of the problem, and therefore each will solve it in his own way.
If there is a problem with the Aquastop sensor, you will have to replace it! Buy a new part and replace the broken one. To do this, carefully free yourself from the tray and then disconnect the component from all latches and wires holding it. Install the new sensor in the same way as the old one and return the pan to its place!
Most automatic washing machines are equipped with a self-diagnosis function for faults. If any part fails, a code is displayed on the display of the unit, telling the user about the problem that has arisen. Siemens washing machines also have a database with programmed fault codes. What is evidenced by error F23 suddenly appearing on the screen in a Siemens washing machine, we will describe below.
[custom_ads_shortcode2]
Decoding
If the model is equipped with a display, F21 is displayed. Everything is clear here. On machines without a screen, the malfunction is indicated by blinking three spin indicators: 1000, 800 and drain.
To check the first two points, you need to remove the motor. This is an important procedure that requires physical strength, as you will need to tilt the washing machine.
Let's look at the necessary step-by-step actions:
I work in the household appliance repair industry. Extensive experience in restoring washing machines and dishwashers.
Important! Wear protective gloves while working. You may hurt your hands.
We check the tachometer generator using a tester. It should not be in a gap and produce little voltage. Please note that this failure occurs quite rarely. Bosch and Siemens motors are famous for their reliability.
Brushes are diagnosed only visually. To do this, you need to remove them from the holders, first pulling out the brass bar and removing the contacts from it.
Important! If the length of the brushes is less than 1 cm, then replacement is required!
Grinding in brushes
First of all, we check the integrity of the collector lamellas. If they start to deflate, you can sharpen them. But this is a temporary measure. Such an engine needs to be changed, or a new rotor must be found.
Be sure to remove brush dust from all accessible areas of the electric motor. We also clean it from the grooves between the collector slats.
The brushes are installed taking into account the inclination towards the rotor!
The grinding procedure is performed as follows:
Do you wash your shoes in the machine?
Module faults
If you do not understand electronic circuits and do not understand the operating principles of an automatic washing machine, then it is better to entrust the repair of the control board to a trusted technician or a specialized service that provides service with a guarantee.
Even installing a new module is not so easy. If you mix up the contacts or chips, it can burn out completely. And they cost quite a lot - from 7 thousand to 20 thousand rubles for individual models.
Let's check the pump thoroughly
If the hoses and pipes do not cause suspicion, we turn our attention to the pump. It may become clogged, burn out or crack. In some cases, an amateur craftsman can carry out repairs with his own hands. But first you need to get to the details.
- We turn off the power to the machine, turn on the water supply tap and disconnect the drain hose from the sewer pipe.
- Open the drain hatch located in the front lower right corner.
- We empty the machine through the emergency drain or garbage filter.
- We provide free access to the unit from all directions.
- We prepare rags and containers for collecting water.
- We take out the powder receptacle by sharply pulling it towards ourselves.
- Turn the washer onto its right side.
- We remove the bottom by prying it up, pulling off the latches and disconnecting the leakage sensor wire.
Don’t rush and check the pump’s functionality with a multimeter. Most often, the problem lies not in the electronics, but in the debris present inside the case. Despite a well-thought-out filtration system that allows foreign objects and dirt to settle in the garbage filter, some hair and fur find their way into some spare parts. Therefore, you will need to disassemble the pump and clean it of any debris that impedes its operation. It's easy to do:
- fix the location of the wires on the camera or using markings;
- disconnect the connected wiring;
- loosen the clamps with pliers;
- remove the hose and pipe;
- Hold the pump firmly by the body and turn it half a turn counterclockwise.
We insert a screwdriver into the existing hole at the middle joint and remove the top cover. Now we carefully inspect the internal mechanism, remove scale and dirt, check the integrity of the gaskets and clean the contacts. After this we test with a multimeter. If the pump is working properly, a three-digit number will be displayed on the display, and the appearance of “0” or “1” will indicate the need for a complete replacement.
When the hoses are clean and the pump is running, there is a good chance that the control board is damaged. Independent attempts to correct the situation are fraught with additional breakdowns, so we strongly recommend that you entrust electronics repair to professionals.
Reset error
For Bosch and Siemens washing machines, it is not enough to fix the problem that led to error F21. It still needs to be reset. Without this procedure, SMASMA will not work.
Different models have their own methods. Let's consider one of them:
It is not always possible to do it right away. Sometimes you need to repeat 5-10 times.
Important! On some models it only works when the “spin” button is pressed!
The second way to reset error F21
I work in the household appliance repair industry. Extensive experience in restoring washing machines and dishwashers.
If you don't succeed after several attempts, you can try 10 seconds instead of 20.
Do you wash by hand?
In 99% of cases, this error occurs after the brushes are worn out!
How to reset error F21?
Reset error
- Set the program selection knob to position “0”.
- Counterclockwise we move one division.
- Press the “Start” button and hold it for a few seconds.
- Return the handle to the neutral position.
- We wait for a while.
- The error has cleared.
Interesting materials:
How to make jamon correctly? How to properly give a cat an injection in the thigh? How to make a business card layout correctly? How to properly make a hair mask from gelatin? How to properly massage the cervical region? How to properly massage the collar area? How to do a bridge from a standing position? How to properly make a dough for yeast dough? How to make a dough dough correctly? How to make dough correctly?
Siemens washing machine error codes
Error codes usually consist of Latin letters and numbers. The most common codes that appear are f17, f18, f23 and f57, but other values are also relevant and may appear on the screen.
If a Siemens machine displays error F01, this means that the sunroof is not closed properly. You should check how the laundry is stacked and make sure that the door closes properly.
Code F02 notifies that the Siemens washing machine is not drawing liquid. You need to check the presence of water and pressure, make sure that the inlet tap is open, inspect the water intake hose and the filter mesh for blockages.
This code notifies that the equipment cannot drain the water. You need to clean the filter, make sure that the pipes and hoses are not clogged with debris, inspect the pump, make sure that it is not clogged and has no external damage. You also need to ring the part and replace it with a new one.
Code notifying about water leakage. It is necessary to check the tightness of joints and connections and find the cause of the leakage of the Siemens machine.
The wash does not start because the door is not slammed. You need to slam it shut tighter and restart the selected program.
Error F17 notifies that the Siemens machine does not fill with water. This indicates that the inlet valve is closed, the pressure is low, and there is a blockage in the liquid filling system.
Error F18 reports that draining water takes a very long time. There may be a blockage in the drain system, a breakdown of the pressure switch or pump. It is necessary to check the drain filter, the hose for blockages, inspect the pump, and then perform diagnostics and test the pressure switch and pump. Replace the broken part.
A code notifying that the water is not heating up or is heating up, but for a very long time. To eliminate the error, you need to diagnose the condition of the heating element. It may have significant lime deposits on it or may be damaged. The problem could also be a temperature sensor or low voltage.
The washing machine heats water when it is not needed. Damage to the temperature sensor or heating element relay.
The washing machine control unit is not functioning correctly or the drive motor is not working correctly and does not rotate the drum. To eliminate the failure, you need to check the control triac, tachometer and reverse relay one by one.
Temperature sensor (NTC) error code. It may be broken or a short circuit has occurred, or an open circuit may also occur.
Error F23 indicates the activation of the Aquastop protective system. This happens if water gets into the pan of the machine or the circuit responsible for the operation of this system breaks. It is necessary to check the AquaStop protection for serviceability and, if it functions correctly, inspect the washing machine to detect leaks or broken joints.
If a Siemens washing machine displays error F25, this is an incorrect operation of the water turbidity sensor. The drain system may be clogged, the pressure switch is damaged, or limescale has formed on the water sensor.
The pressure sensor is not working correctly. It is necessary to diagnose the unit and test the connecting circuit.
Pressostat error code. It is necessary to diagnose the unit and inspect the wiring, test the part and circuit.
The water flow sensor provides invalid information. It is necessary to diagnose the unit and wiring.
Flow sensor does not detect water. The liquid fill valve may be closed or the pressure may be lower than required. This error code may also mean that the inlet filter is clogged, the magnetic valve or pressure sensor is damaged.
The water in the tank is above the required level. You need to check the functionality of the pump, the fill hose for blockages, and the magnetic valve. Another reason is a malfunction or incorrect setting of the pressure switch. This code may also be caused by a clog in the drain.
The door lock does not function. The reason is a broken lock, a stuck tongue, a damaged cuff, or a sagging door.
The hatch locking system is broken. The reason is the control triac or relay failure.
F37, F38
The temperature sensor (NTC) is broken or shorted. It is necessary to diagnose the part and wires from the sensor to the central board.
Synchronization error. Notifies about incorrect voltage in the network.
The Siemens washing machine motor operates randomly and at high speeds. There may be a breakdown of the motor, tachometer, or failure of the control triac.
The motor does not turn. To reset the error, you need to check the tachogenerator for functionality, make sure that there are no things stuck between the drum and the water tank, and that the motor and drum are not blocked. Another reason is a broken triac.
The motor only rotates in one direction. In addition to checking the motor, you need to diagnose the triac and reverse relay.
Error F57 indicates low voltage. To fix the problem, you need to connect the Siemens washing machine through a stabilizer.
Code F59 alerts you that the 3D sensor is reading above or below what is required. Possible wiring break or broken contacts, power module failure, 3D sensor defect, SoftWare error.
Flow sensor values are higher or lower than normal. The sensor has failed or turbulent turbulence has occurred in its tubes or the assembly itself. It is necessary to diagnose the part, inspect the filter in the fill valve, ring and inspect the integrity of the wires from the sensor to the control unit.
Problems with the door operation. It may be open or the security lock has been activated. It is necessary to diagnose the lock: inspect its mechanical elements and test the wiring.
If a Siemens washing machine triggers error F63, this indicates problems with functional protection. An error has occurred in the software or the central processor is damaged.
The card is encoded incorrectly. The coding between the power and main modules is incorrect or the software between them is incorrect.
Engine problems. To understand how to correct the error, you need to diagnose the motor: inspect the condition of the brushes, measure the resistance, integrity of the wiring and contacts, check the control triac and the condition of the control module.
This code indicates that the control unit is incorrectly coded or there is a firmware failure. It is impossible to fix such a breakdown on your own; it is recommended to turn to professionals.
What can be done?
Once the possible reasons for the appearance of a fault code on the screen have become clear, you can take action to fix the problem. The first step is to stop the running washing mode, and then drain the water from the drum. The liquid from the system must be completely removed.
After the water has been drained from the tank, be sure to turn off the power to the SMA.
Next you will have to drain the water from the washer tray. The machine should be tilted so that water can easily pour out from under it. To completely eliminate the breakdown, you need to find the location of the leak. To study the internal elements of the system in detail, you need to remove the wall of the machine body.
What to do next? First, you should inspect the inlet hose for damage; if a defect is found, it is advisable to install a new hose. Then check whether the connections of the pipes are airtight. Then check the pump, maybe the pump is the root cause of the leak.
Continuing the diagnosis, inspect the sealing lip for cracks. Check if there is any blockage in the detergent tray. If you still cannot correct the situation, examine the installation location of the oil seal; perhaps the part has worn out and is causing a leak. Finally, you should inspect the surface of the tank; if a crack is detected, it must be treated with a sealant. In cases where the pan is completely dry, most likely there is a problem in the Aquastop system. Here it is necessary to inspect the contacts for disconnections and check the integrity of the circuit. The sensor may need to be replaced.
An ordinary user who does not have special knowledge can carry out repairs with his own hands. Having thoroughly understood the problem and carefully examined the parts of the MAS, it will not be difficult to detect a breakdown.
Almost all modern Siemens washing machines have a sophisticated electronics system that allows you to independently diagnose a breakdown and even solve it in some cases. Now we will look at the most common errors of Siemens washing machines and how to eliminate them. Even if you cannot cope with the repair yourself, the technician will be able to take all the necessary equipment for repair, knowing the cause and nature of the malfunction.
[custom_ads_shortcode1]
What failures does the code cause?
The main merit of Siemens machine fault codes is that they allow you to narrow down the search for a breakdown. So, the illuminated inscription from F21 indicates a forced stop of the drum. To correct the situation, we first correctly diagnose the source of the problem. They may be:
The mentioned malfunctions prevent the full functioning of the control system and the operation of the motor. The drum stops rotating and the machine cancels the set cycle. Despite the seriousness of the breakdown, you can determine the causes and carry out repair work yourself. Step-by-step instructions on what to do when error F21 appears looks like this.
Having placed the engine on a flat surface, we begin to sequentially check it for existing faults. First of all, let's inspect the tachometer generator. On Siemens machines, this sensor breaks down extremely rarely, so its failure is unlikely.
We test with a multimeter, connect the probes to the contacts and evaluate the result: the final voltage should not be high.
Next, we turn our attention to electric brushes. They are located on both sides of the engine and are removed from the housing after unscrewing the retaining bolts. We take them out of the holders by pulling out the brass bar and carefully disconnecting the contacts, and measure the carbon tip. If the length is less than 0.7-1 cm, we replace both brushes with new ones.
Check for blockages in accessible places
Knowing what to do when code F18 appears, you can check the drain system yourself without outside help. Moreover, the repair does not require special knowledge and experience. The main thing is to act consistently and adhere to the given instructions.
First, let's inspect the water supply components for blockages. We proceed like this:
- Disconnect the washing machine from the power supply.
- We find a drain hatch in the front lower right corner of the body.
- Open it with a flat-head screwdriver so that the two latches holding the door engage.
- Prepare dirty rags and a container to collect water.
- Take the emergency hose located next to the filter, loosen the clamp and drain the water.
Important! If the emergency hose is empty, it means that the drain pipe is clogged and water cannot leave the tank (what should be done in this case is at the end of the section).
- Unscrew the garbage filter.
- We thoroughly clean it of scale and dirt.
- We inspect the pump impeller, and if there is wound hair, we ensure its free rotation.
- Remove the clamps on the drain hose, remove and clean under a strong stream of water.
It’s rare, but it happens that garbage accumulates not in the machine itself, but in the public sewer system. It’s easy to check your guess: turn on the spin mode and lower the end of the drain hose into the toilet, sink, bathtub or basin. Freely flowing water removes all suspicion from the equipment.
Now let's go back to the drain pipe. It connects the pump and the tank, and if there is a lump of garbage in the hose, the water is blocked and cannot escape from the drum. To confirm the assumption, you will have to get to the pump volute through the bottom of the machine.
Most often, Siemens units do not have a bottom panel, so it is enough to tilt the housing back, reach the tube, disconnect it, drain the accumulated liquid and check for blockages. Rinsing under strong water pressure will help eliminate the damage. If there is a pan, first unscrew the holding bolts, not forgetting to carefully unfasten the leakage sensor wire. The latter is provided for an emergency stop of the machine when water gets into the basement compartment to avoid flooding and short circuits.
Checking the engine correctly
Do-it-yourself repairs continue with a more complex procedure - checking the engine for the integrity of the lamellas. To do this, completely remove the rotor from the motor and inspect the collector. If peeling or blowing is noticeable, it is necessary to replace the engine or rotor (if peeling is up to 0.5 mm, you can temporarily sharpen the surface).
Be sure to clean the engine housing from any existing dust and contaminants. We pay special attention to the grooves between the lamellas and polish the entire surface. You should not neglect grinding in, which is carried out like this:
Afterwards we take precautions. For the first 2-3 cycles, load the drum halfway and select low powers. Next, we use the machine in the usual way.
Source of the article: https://sssw.ru/ekspluataciya-i-remont/simens-oshibka-e23.html
Error E23 Bosch washing machine: how to fix, causes, Siemens washing machine error E23 how to fix.
Intake valve problems
What to do if cleaning the filter mesh does not work? You will have to check the filling valve of the Siemens washing machine. It is installed directly under the top cover of the unit, attached to the rear wall. After removing the top panel, you will definitely see an element with several connected tubes through which the liquid enters the powder receptacle. The algorithm for repairing an intake valve with your own hands will be as follows:
- remove the top cover of the case by unscrewing the pair of bolts holding it;
- Inspect the solenoid valve; it may have visible damage.
If the visual inspection is uninformative, you will have to remove the valve. To do this, open the metal clamps and disconnect the pipes connected to the valve. Disconnect the power supply from the element. Before removing the wires, it is advisable to photograph the connection diagram to avoid mistakes during reassembly. All that remains is to unscrew the bolts securing the part to the wall and remove the valve.
It is recommended to carry out diagnostics of the inlet valve over a sink, bathtub or empty container so as not to wet the floor covering.
First, inspect the device and its pipes for blockages. Then connect the inlet hose to the valve and start the water supply. A properly functioning element will not allow leakage. If there is leakage, a new valve will have to be installed.
Further testing should be done with extreme caution. A voltage of 220 V is applied to the coils of the element. During this procedure, the section should open up and fill with water. This testing method is dangerous, since a short circuit may occur when liquid and electricity come into contact.
A multimeter will help you accurately understand whether the filling valve needs to be replaced or not. The measuring device is switched to resistance determination mode. The tester probes are applied one by one to the valve winding. The working sensor should produce a resistance of about 3 kOhm. There is no point in repairing the solenoid valve. It is necessary to purchase a new spare part and replace the failed element. The algorithm for action is as follows:
- secure the valve to the MCA wall with a fixing bolt;
- connect the wires to the required connectors;
- attach the hoses in place using fixing clamps;
- Replace the top panel of the case, tighten the retaining screws.
By following this sequence of actions, you can easily replace the filling valve, the breakdown of which could cause error F17. After completing the steps, turn on the Siemens washing machine and run a test wash.
Error E23 on a Bosch washing machine
Automatic washing machines (SMA) from Bosch have a self-diagnosis function: during testing, an alphanumeric code appears on the display screen, which determines the probable cause of the malfunction. The letter, depending on the model of the device, may change, for example E23/F23. You can fix error E23 on a Bosch washing machine yourself or with the help of a technician who will make repairs and give operating tips.
When can you fix it yourself?
Don’t rush to call a specialist; perhaps everything is not so serious, and the error can be corrected on your own. Here are the cases in which the help of a specialist is not required.
- Drain filter clogged. You need to clean the filter regularly; if you have not done this before, then it is very likely that this is the reason. To clean the filter, please refer to the appropriate section of your machine's instruction manual or use the general filter cleaning instructions on our website.
- The drain hose is squashed or kinked. Check it along its entire length and straighten it if necessary.
- Blockage in the sewer. A common problem with washing machines connected to the sink siphon in the kitchen or bathroom. The siphon becomes clogged, preventing water from draining from the machine. Pull the free end of the hose out of the drain, place it in the toilet, bathtub or any container and start the drain. If the washing machine starts pumping out water normally, congratulations, everything is fine with the machine, you need to clear the blockage in the sewer.
- One-time failure of the electronic controller (control unit). Try unplugging the washing machine for 5 - 10 minutes, then plugging it back in and start draining. Perhaps there was simply an electronics failure, and the machine will work after it is “rebooted”.
Reasons for the error
E23 has a more common analogue, F23 - it is used on most models, but the reasons for the occurrence of the code are the same. This signal is given by the Aquastop system sensor when water appears in the pan of the SMA housing. The reasons for triggering the protection are the following cases:
The washing machine control module is connected to E23: a voltage failure in the electrical network can initiate the transmission of a false command from the sensor, and the CMA will stop washing. To make sure that the error code was displayed due to an external reason, turn off the program and disconnect the machine from the network for 5-15 minutes. If there were no problems when restarting, there was a one-time system failure.
Let's look at how the leakage sensor works. In Bosch washing machines, the lower part of the body is covered with a tray in which the signal float is located. When water enters the container, the foam-based module rises, the protection is activated: a command to stop the program is sent to the control unit - the display shows error E23 or F23.
How to fix the problem
The priority actions when a malfunction is confirmed: turn off the power to the machine, disconnect it from the water supply, empty the tank of liquid through the drain filter, and remove laundry from it.
The search for the reason for stopping the car according to E23 begins with the simplest actions, gradually moving in the direction of complex operations, and eliminates the identified malfunction.
The algorithm for checking work items is as follows:
After eliminating the malfunction, a test run of the SMA is performed. If error E23 does not appear on the screen, the repair was performed correctly.
Where to start checking?
The very first thing on the list of what to do in case of error E18 is to prepare the machine for diagnostics. We stop the washing with the “Stop” button, disconnect the machine from the power supply and turn off the water supply tap. Next, disconnect the drain hose and pour out the remaining liquid. Then we move the unit away from the wall or take it out of the closet and begin a sequential check of all possible sources of failure. We proceed in this order.
If there is heavy dirt, hairballs, scale or other foreign objects, all parts must be thoroughly cleaned. It is recommended to test the hoses and pipes, and then tighten all terminals and clamps. If there is damage on the face, we change the pump.
Upon completion of all manipulations, restore all connections, not forgetting about reliable fixation and tightness.
Useful tips
Recommendations from service technicians always guide users toward preventive maintenance of household appliances, rather than repairing them. Compliance with the manufacturer's instructions for operating the washing machine guarantees its trouble-free operation for 10 years. Some tips from professionals on how to protect the SMA from leaks:
Experts advise starting the search for the cause of error E23 by checking the version about a foreign object under the float. If the machine body is tilted, the obstacle may roll out and the code will disappear from the display. The instructions require checking your clothing pockets before washing: small iron can pierce the pump body. The manufacturer's recommendations should not be neglected - this leads to the self-defense of the SMA.
Source of the article: https://tehno.expert/stiralnaya-mashina/oshibka-e23-na-bosch.html
Error E23 in a Bosch washing machine, Siemens washing machine error E23 how to fix.
Possible faults requiring repair
According to the experience of RemBytTech specialists, the appearance of the E17 code in Siemens brand washing machines is associated with the following breakdowns.
| Signs | Breaking | Repair or replacement | Cost* (work only) |
| The Siemens washing machine does not draw water at all or only during the rinsing stage. Code E 17 appears on the screen. | The fill valve is broken. This part consists of a housing, a damper membrane and an electromagnetic coil. Normally, the coil opens the membrane and the machine fills with water. Typically, it is the coil that fails, causing the valve to stop functioning. If the SMA is equipped with a single valve, water will not flow into the machine at all. If the valve is two-section, then two options are possible: water will not be collected only for washing or only for rinsing. | The faulty valve must be replaced with a new one. | from 1500 rub. |
| The machine does not fill with water and goes into error F17 or E17. | (water level sensor in the tank) is faulty It is likely that: |
* The price is only for the work of the master, spare parts are paid additionally.
If your Siemens issues code E17 or F17 and you cannot fix the error yourself, it’s time to call the specialists:
RemBytTech specialists have repaired more than one thousand Siemens washing machines. They will help yours too. We carry out all work at home, we leave within 24 hours of receiving the application, we provide a guarantee for up to 2 years. We will take care of your equipment!
Source
Causes of leakage
This error on a Bosch washing machine is interpreted in almost the same way as error F23. It notifies the owner of the equipment that the sensor of the system providing protection against leaks has been activated. This sensor is located in the pan of the machine.
The operating principle of the Aquastop sensor is quite simple. There is a special segment in the washer tray that is connected to a float. When water enters the pan, the float begins to rise. As a result, the sensor is triggered, and then error code E23 appears on the machine display.
There are a number of reasons why a leak can occur:
Common problems
Siemens washing machines have weak points that can cause problems if operating rules are violated.
Here are the most common faults:
The reason may be a problem with the pump - a broken drain pump. But most often the problem is clogging. If the unit does not drain water, the drain pipes are likely clogged. Without cleaning, the pump motor may burn out.
· The water does not heat up.
This can happen due to several faults. The first is a burnt-out heating element, the second and most common is a broken thermostat. The third failure is rare, but it is the most expensive to repair - the control module.
· Noise during the spin process.
This sign suggests that you need to pay attention first of all to the age and methods of operation of the equipment. When the unit is more than 4 years old and is used frequently, the bearings are most likely worn out. Typically, the machine will not work much in this mode. If the oil seal and bearings are not replaced, the entire assembly will fail. In this case, you will need to completely replace the tank, and this is an expensive repair.
For any problem, even a minor one, the equipment needs to be repaired. Since a washing machine is a complex piece of equipment, repairs require experience and professional skills, as well as special tools and diagnostic devices. For this reason, it is important to contact professionals.
Aquastop sensor dysfunction
Experts recommend checking the pan before installing the Aquastop system. There should be no debris in it. Small debris can get on the float, causing it to rise.
Debris in the pan may cause the sensor to not work if a real leak occurs.
It should be noted that the Aquastop sensor is very sensitive. Error E23 can appear even if you move or install washing equipment carelessly.
