Most washing modes in an automatic machine end with a spin cycle. This allows you to remove excess moisture from the laundry and prepare things for further drying.
If the Samsung washing machine does not spin, this may indicate a breakdown and the need for repair.
Why the Samsung automatic washing machine stopped spinning clothes, how to identify the breakdown and fix it, we will tell you in the article.
Reasons why the Samsung washing machine spin does not work
The absence of a spin cycle may indicate serious malfunctions, without which the full cycle of washing items will be impossible.
Breakdowns that affect spinning:
Lack of drainage, in which the washing machine does not proceed to the next stage of operation - spinning.- Worn motor brushes.
- Drive belt stretch.
- Tachometer failure.
- Failure of the control module.
- Wear of shock absorbers.
- Bearing wear.
- Electric motor failure.
- The pressure switch is malfunctioning.
To determine the cause of malfunction, you must:
- analyze the condition of the machine itself,
- what messages are shown on the display,
- whether the device makes any uncharacteristic sounds when operating, etc.
Possible breakdowns when the washing machine freezes on the spin cycle
Most often, the machine hangs on the spin cycle. As in the case of washing with rinsing, the cause of freezing may be breakdowns of the pressure switch, control unit, tachometer and motor brushes. Here we will look at malfunctions that are specific only to spinning.
Bearings have fallen apart - from RUB 3,000*
When the spin is turned on, the vibrations of the drum and the entire machine increase. If the bearings are in “poor” condition, the drum will play and shake violently during acceleration. If the SMA can still cope with washing and rinsing in this state, although it creaks more than usual, then it can no longer wring out normally due to strong shaking. When trying to accelerate the drum, the washing machine rattles very loudly and the drum does not gain speed.
In addition to the lack of spin, a washing machine with faulty bearings can stain laundry with black grease from the oil seal. And if you remove the back wall of a front-loading machine or the sides of a vertical-loading machine, you can find rusty stains on the tank from the location of the bearings.
HOW TO FIX
The bearings and seal need to be replaced. It is best to do such repairs immediately when the first signs of damage appear. Otherwise, the malfunction may cause the crosspiece to break or damage the tank, and then the entire tank assembly will have to be replaced.
Troubleshooting
You should analyze the situation with the condition of the washing machine methodically, starting with the simplest options, checking each component step by step.
Consumer errors
Not in all cases, the lack of spinning indicates a breakdown. First you need to assess the situation and pay attention to possible consumer mistakes.
Situations in which the problem is not in the spin cycle:
Drum overload. There are too many things embedded that, having absorbed water, have become even heavier. The machine cannot gain speed and spin the laundry. Putting some of the laundry away from the drum will help solve the problem.- Another situation in which things do not spin is when you select one of the delicate modes. Or an accidental, or maybe special, disabling of this function.
- Imbalance of things in the drum. This situation may arise when things gather in one lump during washing, and the machine itself cannot distribute them evenly. For example, a tumbled blanket or duvet cover, into which all the other things from the drum got caught.
- The mode of low spin speed (or no spin at all) is selected. If it is possible to set different spin intensity, then the minimum one may be accidentally selected.
When starting the washing machine, you should make sure that the program is set correctly and the total weight of the items in the drum does not exceed the permissible limit.
Determining the source of the failure
In rare cases, an accidental failure may affect the operation of the washing machine . Such factors include a voltage drop in the network or a problem with the water supply. When the operation of external communications stabilizes, it is necessary to restart the spin function and monitor the operation of the washing machine.
Slight rotation of the drum for several minutes (up to 10) may be a normal situation - the machine simply straightens the laundry, distributing it evenly throughout the drum. If after this the work continues as normal, there is no need to worry, since there is no problem.
In some cases, the washing stops, and the washing machine itself reports a failure by displaying an alphanumeric error code on the display. It could be:
- E4,
- UB,
- .
It is almost impossible to determine at first glance what the problem is, so it is necessary to carry out the analysis gradually - from node to node.
In some cases, the type of breakdown can be determined by the condition of the machine:
| "Behavior" of the washing machine | Which node should you pay attention to? |
| Lack of spin speed | Drive belt |
| The drum does not spin at all or does not gain momentum | Tachometer, control module |
| No drain - the cycle does not reach the spin cycle | Pump, pipe, filter, drain hose, sewerage, control module |
| No spin speed, sparking | Motor brushes |
| Excessive vibration when trying to spin the drum; spinning does not occur. There may also be an uncharacteristic knocking sound of the drum against the body | Shock absorbers |
| When you try to spin the machine, it makes loud noises and rattles. If you swing an empty drum by hand, it dangles freely on the shaft. In addition, there may be rust marks on the outside of the tank. | Bearings |
| “Hanging” on the spin cycle. If you start again, the drum does not move. At the same time, the hum of the engine may be heard. It is also possible that plugs may be knocked out or, conversely, complete failure of operation. | Electric motor |
| The drum rotates during the spin cycle, but there is no spin as such. | Pressostat |
Even despite the characteristic signs inherent in a particular breakdown, in-depth professional diagnostics of the device may be required.
What to do?
If consumer errors are excluded, you can move on to analyzing the operation of the nodes. It is better to do this in the following order: start with the most accessible ones, leaving the most difficult ones for later.
Preliminary preparation of the machine:
- if there is water in the washing machine, it must be drained (naturally or through an emergency drain);
- disconnect the washing machine from the power supply;
- shut off the water supply to the device;
- pull out the washing machine in such a way as to provide convenient access to its rear wall;
- pull out the powder receptacle.
Drain violation
If the washing machine does not drain the water, it cannot proceed to the spin cycle. In this case, it is necessary to gradually sort through all possible problems associated with the drain.
It’s better to start by cleaning the drain filter, since even if the problem is not there, regular cleaning of this unit will benefit the car.
Next, you need to diagnose the operation of the drain pump , check the permeability of all systems associated with draining water.
The drive belt has expired
If the drive belt is stretched, it does not provide the necessary contact with surfaces. If it “slips,” the part must be replaced, since it cannot be repaired.
Tachometer failure
The tachometer is an element of the washing machine that is involved in the rotation of the drum. This unit is responsible for controlling the number of engine revolutions .
If it breaks, the washing machine does not rotate the drum intensively. As a result, spinning is either not performed or is performed very weakly.
The tachometer is a fairly reliable element that rarely breaks.
Control unit failure
The control unit is a board that connects to buttons and sensors on the front panel , and also transmits signals to the components of the washing machine. It is located in the upper part of the front side of the washing machine.
Diagnosing a fault is a complex process that requires special knowledge and tools (soldering iron, multimeter, etc.).
Violations may be associated with burnout of individual elements and tracks, broken contacts, as well as damage to the loop. It is better to entrust diagnostic and repair work with electronics to a specialist.
Motor brush wear
As the drum rotates during spinning, the motor is activated. In cases where it sparks and does not create the required torque, it is necessary to inspect the condition of the motor brushes . If they do not make good contact with the manifold due to wear, the technician replaces them.
Shock absorbers are worn out
Shock absorbers in a washing machine are needed to dampen drum vibrations during the washing and spinning process. When the shock absorbers wear out, vibrations are not dampened, and electronic sensors prevent the drum from spinning.
As a result, spinning is not performed. If such a breakdown occurs, the shock absorbers need to be replaced.
When shock absorbers wear out, it is necessary to replace both at once , even if the degree of damage to one of them is insignificant.
The video will tell you about replacing the shock absorbers of a washing machine:
Bearing failure
Bearing wear can occur during prolonged use of the washing machine. During this time, the oil seal begins to lose its tightness, which causes water to enter the bearings. This causes lubricant to be washed away and leads to rusting, and vibration and rotation make the situation even worse.
Motor damage
If the washing machine cannot spin, you should not miss the possibility of such a serious breakdown as electric motor combustion . Malfunctions in the operation of this unit can be caused by a short circuit, stator failure and other circumstances.
The technician determines the degree of damage and makes a conclusion about the possibility of repairing the equipment. If the electric motor cannot be restored, it is replaced with a new one.
The pressure switch is broken
A pressure switch is a sensor that controls water level . The signal from it about the water level is sent to the control module.
If the signal is normal, which corresponds to the actual liquid level, the control module, after draining, gives a signal to spin.
But if the pressure switch gives incorrect signals, the control module does not “give the go-ahead” for spinning. This situation can occur when the pressure switch freezes on a signal indicating that the tank is full of water. Even if in fact all the liquid has been drained, the control module does not receive information about this.
The technician diagnoses the pressure switch - checks for blockages and damage . After the functionality of this unit is restored, the washing machine will begin spinning.
The video will show you how to check the pressure switch in a washing machine:
Malfunction caused by the user
Most often, the spin cycle in the machine does not work due to the user’s carelessness. The reason may also be a violation of the rules for operating washing equipment.
For example, if the washing mode is selected incorrectly, the laundry pulled out of the drum will be wet or damp. It should be noted that some delicate wash cycles do not spin the laundry. Due to this, it is possible to preserve the delicate fabric.
Users often accidentally turn off the laundry spin cycle themselves. This problem can be fixed quite easily. You need to start spinning the laundry after finishing the wash.
A clog in the pump or drain filter can cause serious problems with your washing equipment. Such blockages occur due to lack of proper care of the washing machine.
The filter must be cleaned regularly. This way you will prevent clogging of the drain system, which causes water to stagnate and an unpleasant odor to appear. If the equipment does not spin out the laundry and the drum contains water, then first of all you should check the drain filter.
In Samsung washing machines it can be found behind a small door, which is located in the lower right corner of the machine. There is a hose near the filter cover. You can use it to drain the remaining water from the drum. Next, you need to unscrew the drain filter and remove the blockage.
Poor spinning of laundry can also occur when the drum is underloaded or overloaded with laundry. If you load bulky items into the unit, the load on the washing machine parts will increase, and the spin of the laundry will be of poor quality. Also, do not machine wash items that are too light. They will cause imbalance and perform poorly.
Calling a master: how to find and how much to pay?
Sometimes you can even cope with a problem in the absence of a spin on your own, but it is better to entrust high-quality diagnostics and repair of components to a professional. To do this, you should contact a company that provides repair services for household appliances , and Samsung washing machines, in particular.
The cost of repairs consists of the prices for the work of the technician, the price of parts requiring replacement, and consumables. Depending on the complexity of the breakdown, the cost of repair increases. There may also be a difference in the price list of companies.
The average price for repairs in the capital (excluding the price of parts) is:
diagnostics of the pressure switch, repair, replacement – from 1,600 rubles;- replacement of shock absorbers - from 2,200 rubles;
- electric motor repair/replacement – from 2,000 rubles;
- replacement of bearings – from 3,300 rubles;
- replacement of tachometer – from 2,200 rubles;
- drain cleaning – from 1,100 rubles;
- replacement of motor brushes – from 1,400 rubles;
- replacement of the drive belt - from 900 rubles, etc.
The final cost is determined in each specific case.
You can find a Samsung washing machine repair company on the Internet. For devices that are still under warranty, you need to contact the service center with the problem . Information about them is indicated in the documents for the washing machine.
The technician is directly called by phone. The dispatcher needs to describe the breakdown of the washing machine and name the model (it is indicated in the passport for the device).
It is not advisable to turn to the services of a private craftsman, since the result can be poor quality work, installation of used parts rather than new ones, etc. In the worst case, you can even run into scammers who will scam you out of money and disappear.
Expert advice
Recommendations from technicians who repair washing household appliances will help you avoid problems with the spin function in your washing machine:
- Do not overload the washing machine. This will allow the engine to maintain functionality and prevent it from overloading.
When washing, you do not need to add more washing powder than recommended. Abundant foam due to its excess can damage the water level sensor.- Before putting it into the drum, it is important to check the contents of the pockets and not place things in it that require repair - with poorly sewn buttons, dilapidated ones, etc. Small objects are the main cause of not only blockages, but also breakdowns.
- Do not use the spin function when washing shoes, as this creates an overload on many components and can lead to equipment breakdowns.
- Ensuring a stable voltage in the electrical network will prevent burnout and failure of the washing machine elements.
Find out more about repairing Samsung washing machines in this section.
Problems with the pump
The pump is a small motor that moves water in the washing machine. If this part is damaged, the machine will not be able to drain the water, and with a drum full of water, spinning is impossible. As a result, it will not be possible to wash things.
You can check the pump as follows:
- Take out the container to receive the powder.
- The car is laid on its left side. This action will prevent water from leaking and getting on electrical parts.
- Remove the pallet.
- Find a pump and a pipe (at one end it is attached to the pump, at the other to the tank. The clamps holding this pipe are removed.
- The next step is to remove the pipe and check it. There should be no accumulated dirt or unnecessary objects inside.
- At the very end, remove the pump. She is inspected for damage.
If this part of the washer is worn out, it cannot be repaired. You need to buy a new pump.
In some cases, an air lock may occur in the pump. This phenomenon leads to the fact that the washing machine does not drain the water, which immediately affects the execution of the specified washing program. It is extremely difficult for equipment designed to pump water to handle air. To solve this problem, you need to follow these steps:
- The drain hose is laid on the floor.
- The drain mode is set on the instrument panel.
- As soon as the accumulated air is released, water will flow from the hose. At this time, the hose is moved to the bathtub or sink.
