Hansa built-in dishwashers 60 cm. How to use Hansa dishwashers

Features of the first activation of the Hans PMM

Of course, before installation and first launch, you must read the instructions. Make sure your water and sewer connections are correct, purchase manufacturer-approved cleaning products, and then get started. The very first cycle is performed without dishes. But there are nuances:

Pour approximately 1 liter of water into the salt container.
Plug in the device and turn on the water supply.
Among the temperature modes, choose medium, most often it is 30°-40°C.
Activate the shortest mode, usually Eco or Express depending on the series.
Click "Start".
After about 10 seconds the device will start.

Safety precautions

In this section, the manufacturer gives valuable instructions, following which you will be able to use the device correctly and definitely not harm yourself:

Check the packaging and integrity of the machine upon receipt. If you have any doubts about the integrity of the device, do not use it, but contact the seller for clarification.
Before connecting the device to the network, the outlet must be grounded. Doing this yourself is strictly prohibited, so you will have to contact a specialist.
Before turning on, check the electrical readings with the readings required for the operation of the Hans dishwasher.
During installation or repair, it is necessary to turn off the power and water supply to the device.
The manufacturer does not recommend using a connection via an extension cord, and also requests that only the original plug be used to plug into the network. The socket and plug must be quickly and easily accessible.
The use of a Hans dishwasher by persons who have not studied safety precautions, or by people with physical or mental disabilities is prohibited if the danger of using the device is high for them.
Separately, the instructions for the Hans dishwasher highlight the use of the device by children. Children over 8 years old are allowed to wash dishes in it, provided they have undergone instruction and understand the dangers that can occur if handled incorrectly. Children under three years of age are not allowed near the device. It is forbidden to play with the machine, drink water from the device, and detergents must be stored out of the reach of children.
During use, remember that the water may be heated, so there is a high risk of getting burned when opening the door while running the program.
To avoid injury from sharp objects, they are placed horizontally in the upper compartment or point down in the cutlery compartment.
It is prohibited to use a Hansa dishwasher for purposes other than its intended purpose - washing dishes.
Solvents must not be used in the device due to the risk of explosion.
Do not sit down, stand up or place heavy objects on the door of the device - the machine may tip over.
If repairs are necessary, you should contact a specialist.

These are the manufacturer’s main recommendations for safe handling of equipment. You can always find out more about the requirements and recommendations in the instructions for your model or use our article, which describes in detail the installation and connection processes of the dishwasher.

How to optimally arrange dishes in boxes

Properly arranged dishes are half the success of washing. Proper layout allows the rocker arms to spray water as efficiently as possible, as well as wash away detergent. Then there are no drips or drips left on the cutlery. Here are some tips from Hans' engineers:

Start loading from the bottom basket/box. After drying or the end of the cycle, they also begin to unload from the bottom.
Pots, pans, and other large items should be placed below.
Maintain some distance between dishes, including cutlery.
It is advisable to place plates and cups, as well as pots, upside down.
It is most effective and safe in those PMMs that have holders and special shelves for cups, glasses, and a separate tray for forks and knives.

Loading

There are several simple loading rules that apply to all dishwashers:

Start filling the device from the bottom basket. In the same way, you need to unload the device.
The largest items - pots and pans - are placed downwards.
There should be a small distance between dishes so that water can freely clean the surfaces.
Place all cookware upside down.

General algorithm of operation

Dishwashers from popular brands such as Bosch, Siemens, Samsung operate on the same principle, although the algorithms and programs may differ. When you turn on a new dishwasher for the first time, you need to conduct a test run to ensure that the connection is correct and to remove factory contamination.

Regardless of the price segment, manufacturer or dimensions of the PMM, there is a single operating algorithm that can be divided into stages:

Preparing/stacking dishes in the compartment.
Loading detergents into special compartments.
Start the program.
End of the cycle.

Depending on the selected program, the washing process may include the following steps:

Pre-soaking is necessary for very dirty dishes with dried food particles.
Washing.
Rinse – rinse off the product and remove stains.
Dry with steam or condensate to add shine and eliminate smudges.

Preparatory stage

At this stage, all dishes are cleaned from large contaminants with a sponge or napkin and placed in special internal compartments

It is important to load the dishwasher correctly, carefully distributing and securing anything breakable, sharp or small, in the top compartment, plates in the middle tray, and large dishes in the bottom compartment.

Soak

This function is optional, can be programmed in a separate mode and is intended for soaking especially dirty dishes with dried food residues. The function is useful if you accumulate dishes during the day and turn on appliances, for example, at night. Over the course of a day, food particles dry out and are more difficult to wash without soaking. This option will allow you to effectively clean all dishes, even with complex stains.

Washing

The main and long-lasting stage in which water of the required temperature under pressure is sprayed inside the compartment, and the dissolved detergent removes all dirt. This is repeated several times during the cycle, then the remaining water is removed through the drain hose.

The average washing time is from 1.5 to 2 hours. The express mode takes 20 minutes, which affects the quality of washing, but allows you to quickly refresh dishes that are not too dirty, or if you need to do it quickly. On long cycles the process can take up to 3 hours.

Rinsing

Upon completion of the main process, the machine drains the remaining dirty water and distributes clean water with dissolved conditioner in the compartment through sprayers to remove residual detergent, eliminate streaks and smudges.

Drying

The final stage, where under the influence of hot forced air or condensation, excess moisture evaporates from the surface of the cookware.

Basic modes and choosing the right one

The basic set of programs in all dishwashers of this brand is the same. This:

Pre-washing, also known as soaking, is for heavily soiled or burnt dishes.
Standard program - suitable for medium soiling and almost all types of dishes.
Delicate - for glass, porcelain, crystal.
Eco mode is economical and environmentally friendly, not suitable for heavy pollution.
Night - the quietest mode, medium in duration. Typically the temperature is 50°C.

There are others, but the most popular ones are listed above.

Program selection

Different models of Hans dishwashers have their own characteristics. We list the main functions that are found in almost all devices:

Pre-wash or pre-soak - used when you need to soak stuck or burnt-on food residues.
High-intensity washing allows you to remove the most stubborn stains at temperatures of +65 - +70°C.
Standard sink - for cleaning dishes from medium to heavy stains.
Eco-wash is used for all degrees of soiling, except heavy. It features reduced consumption of electrical energy, water and detergent.
The delicate wash is suitable for fragile items: glass, porcelain, crystal at a temperature of +45°C.
Quick wash is half as long as the standard cycle and takes place at +55°C.

Basic moments

How to turn on the car? Any instructions for Hansa household appliances are quite detailed and contain about 40 pages of text, diagrams, tables and photos, which are convenient to use both when connecting the device and installing it, and during its direct operation, where you can also see how the machine turns on.

On the first pages, the manufacturer writes a greeting and gratitude for choosing the brand, as well as a recommendation to carefully read the instructions for a specific model before using it.

Instruction sections:

symbols used in the instructions and their interpretation;
safety precautions for handling a Hans dishwasher;
installation instructions;
description of the main parts of the machine;
recommendations for preparation for launch;
description and selection of washing programs;
cleaning and care tips;
possible errors and ways to eliminate them;
device data sheet.

Any Hans dishwasher is equipped with similar information. The instructions are also supplemented with practical advice from the manufacturer.

Important! You will find similar recommendations in the instructions for any equipment from different manufacturers. If you haven’t bought one yet, but are just planning to get a dishwasher, perhaps our reviews of the best models in the following categories will help you:
The dishwasher is small.
The dishwasher is freestanding.

Let's look at the most important points in more detail.

Proper care of your PMM

To avoid damage, use PMM only for dishes that can be washed in it. Do not load wooden or pewter items; not all dishwashers are suitable for washing plastic items. Don't forget to take care of the device. Wipe the doors, clean the filter. Of course, there are models with self-cleaning, but this also requires periodic supervision. The door seal should also be cleaned with a special product or a melamine sponge to prevent mold from forming or drying out.

Why do you need an idle start?

Most owners of new household appliances in the kitchen imagine the first launch of a Bosch dishwasher with full compartments of dishes, which they may have been specially saving for the last week in order to experience in practice all the advantages of owning a unit.

But in the instructions, German manufacturers recommend that the first start-up should be done idle, that is, with detergents, but without loading dishes. This is necessary for:

Removing lubricant residues, small particles of packaging and other elements that have fallen into the internal cavity of the dishwasher.
A closer acquaintance with the operation of the device to see how it draws water, sprays, how quickly cycles change and drying occurs. Having seen this process without internal objects, some better understand the principle of operation and how to arrange the dishes inside.
Make sure that household appliances are in working order and quickly notice the location of the breakdown if something does not work.

Distinctive features

When you decide to purchase a Hans dishwasher, you should learn about the features and advantages of the equipment.

These include:

Stylish, modern design of each model . Any Hans device can fit harmoniously into the kitchen interior;
saving . Thanks to the Hansa dishwasher you can significantly reduce electricity, water and your time, which you can devote to more important matters;
effective cleaning . The machine can easily cope with any degree of contamination, perfectly washing each product.

Arrangement of plates and utensils for cooking

The lower basket is the main part of the dishwasher. Large plates should be placed closer to the edges of the compartment, and smaller or deeper ones should be placed closer to the center. Since loading dishes of the same shape is not always possible or convenient, it is better to alternate flat and deep plates - there should be enough space between them.

It is recommended to wash all cooking utensils separately. This way it can be arranged more rationally without compromising the quality of washing of other appliances. Baking trays and frying pans are placed vertically so as not to block the nozzles. If the additional handles cannot be detached, they are directed up or along the basket. Large and small pots should be loaded upside down, similar to glasses and mugs.

Placing a frying pan in the dishwasher

For a clear example of how to properly wash dishes in a dishwasher, you can watch the instructional video. For example, interesting videos on how to properly use a built-in dishwasher from the German company Bosch, a leader in the production of household appliances.

Types of dishwashers

The Hansa company manufactures and supplies 3 types of dishwashers to the world market:

built- in This type of dishwasher is built into a compartment of a kitchen unit, completely merging with it and not standing out from the furniture facade. The advantages of built-in dishwashers include their compactness, low cost (compared to full-sized models), and low consumption of resources. The capacity of the box is from 10 to 14 sets of dishes;
free- standing Such equipment can be installed in any convenient place, with the possibility of connecting communications. One of the advantages of the dishwasher is the convenient location of the control panel on the front of the door. The maximum load of the dishwasher box is from 9 to 12 sets;
desktop _ The most compact version of dishwashing equipment, with small capacity and a modest range of functions and additional options. The machine is easy to install on a table or countertop. Capacity – up to 8 sets.

Detergents and auxiliaries

Dishwashers use a whole range of detergents and additional products:

detergent;
salt;
rinse aid

The form of release of funds varies:

powder;
liquid;
pills;
capsules.

Washing components can be sold either individually or as a 3-in-1 universal product.

The former are easy to dose and are convenient for short periods because they dissolve faster. Capsules and tablets are more convenient to use because they do not fall apart or crumble. Manufacturers prefer to use tablets because they are easier to load. Some species have a shell that itself dissolves in water. The most famous manufacturers of detergents are Finish, Fairy, Somat.

One of the most common causes of device failure is the formation of scale on parts. In order to prevent this, special salt is used. Dishwasher rinse aid is also important. It makes dishes more sparkling, removes remaining foam, quickly dries the surface, and prevents stains and streaks.

The first product developed for PMM was powder. It is not considered the best today, but is still popular. Its advantages are availability, low cost, efficiency, and rapid dissolution. The disadvantages are that dosing the powder is difficult. There is little salt in the composition, so it must be used. Some powders do not contain rinse aid, so they may leave streaks.

The most preferable option is a liquid product. Its active particles prevent scale formation and effectively soften water. The liquid contains no abrasive particles, so it can be used for delicate dishes. It dissolves well and copes well with stains of varying complexity. Safe for people with high sensitivity and allergies. The step-by-step instructions for the products describe in detail how to use Finish and other brands of dishwashers.

Advantages of devices

Many buyers choose Hansa dishwashers . This is due to the fact that the equipment of this brand is durable, does its job effectively and has good technical characteristics.

Advantages:

ergonomic screen with LED backlighting and indication of mode, time left and water temperature - all premium models are equipped with it;
internal lighting;
economical consumption of electricity and water;
machine operation with minimal noise level;
long service life;
warranty period from the manufacturer for each product;
remembering the last parameters set by the user for cleaning dishes.

Problems and solutions

Due to improper connection and operation, users often encounter problems and breakdowns.

Filling system problems

Such problems are always associated with blockages, so you should know how to eliminate them:

Turn the water supply valve to the “Off” position and disconnect the machine from the mains.
Disconnect the water supply hose from the housing and check for plugs and debris. Do the same steps with the filter and mesh.
To remove stagnant debris, place the filter in water with citric acid.
Perform valve diagnostics by ringing the coils; if necessary, replace worn elements.

Checking the circulation pump

It is better to check the circulation pump when there is no water injection and it does not enter the working space of the machine, because due to the circulation pump, water flows into the rocker arms and the dishwashing function is activated. Diagnostics and repairs will be necessary if you hear knocking, buzzing, or noise.

For repair you need:

Provide normal access to the bottom of the workspace and remove the bottom panel of the housing.
Remove the fasteners and drain pump by turning the pump clockwise.
Remove the special clamps with an adjustable wrench and disconnect the pump, replace the non-working equipment.
Transfer the clamps and mounting bolt from the old pump to the new element and perform the same assembly, only in reverse order.

Drain system malfunctions

If, after washing dishes, the water does not completely leave the workspace and accumulates below, it means that there is a problem with the drainage system. Often this is due to stuck and accumulated debris, to fix the problem you need to do the following:

Remove all plates and glasses from the machine and pull the lower rocker towards you, carefully unscrew the upper rocker.
Check sprinklers for debris. If necessary, clean the injectors using a toothpick.
The drain filter and the metal mesh at the bottom of the working area should also be inspected and cleaned.
If glasses or plates were chipped during the washing process, perhaps a splinter blocked the pump; Wearing gloves, it is necessary to carry out diagnostics.

Replacing the level sensor

In dishwashing equipment, the level sensor is called a pereostat; its function is to monitor the water level in the tank. Failure of this element may consist of physical wear, blockage, or malfunction of the electronic part.

Before a complete replacement, you need to check the element for blockages. To do this, you need to unscrew 2 screws from the bottom of the machine, the mounting clamp, and blow out the tube. The electronic part can be diagnosed using a multimeter.

Heating element diagnostics

The basis of the heating system is a flow-through heater, which is necessary to increase the temperature of the water when cleaning dishes. Its breakdown may be due to the inoperability of the heating element located under the bottom of the Hansa dishwasher. It is better to entrust the installation of the heating element to a specialist; for self-repair, the following is required:

Disconnect the heating element with the pump.
Unscrew the pump fasteners by turning them clockwise and remove the rubber seal.
Remove all tubes and pipes, replace the non-functioning part and reassemble everything in the reverse order.

Leak

To eliminate leaks, it is necessary to identify the exact cause and location; for this, the following occurs:

Carefully inspect the inside and outside of the dishwasher.
Check the quality of door closure and the reliability of the door seals; if necessary, replace them.
Inspect the rubber seals on the drain pump; their wear can also lead to leakage. In this case, it will be necessary to replace the seal or the pump completely.
Conduct diagnostics of the hose at the inlet and outlet, if necessary, tighten the tightening elements or replace the hose.

Hansa brand PMMs are reliable, convenient and functional; for simple and long-term use, each model comes with detailed and understandable instructions.

How to choose and what to pay attention to?

The selected dishwasher should not only be stylish and easy to use, but also multifunctional. This will allow the buyer to select the optimal washing mode for all types of dishes and varying degrees of soiling.

Hans dishwashers have basic programs such as:

express wash – for daily use with lightly soiled dishes. Temperature – 60 degrees;
delicate cleaning of fragile items . Ideal for washing fine porcelain and glassware. Temperature – 45 degrees. At the end of the cycle, there are no streaks left on the dishes;
two automatic programs . Temperature ranges from 40 to 75 and from 45 to 65 degrees. Suitable for all types of dishes, including heavy and old stains;
ECO mode . Washing dishes with minimal use of resources and detergent at a temperature of 50 degrees;
intensive - the longest time mode at a temperature of 60-70 degrees. Suitable for removing soot and old fat;
half load . The mode allows you to wash any number of dishes without reaching the maximum load volume.

Another important parameter is the low noise level during operation of the equipment.

Most models have good performance up to 45 dB, which will allow you to turn on the machine at any time of the day, including at night, without worrying about family members waking up from the noise.

Hans machines have a high energy efficiency class, corresponding to the designations A, A+, A++, A+++ . This will allow all users to save resources up to 40%.

The maximum load of the dishwasher box is from 9 to 15 full sets of dishes.

Program duration for some models

Each mode takes a certain period of time. During this period, the dishes become absolutely clean and dry.

"Eco-friendly" washing program

ECO (ECO) sink is designed for washing dishes that are not very dirty. During this process, small amounts of water and electricity are consumed: an average of 9.9 liters and 0.97 kWh. The longest and optimal mode is 2 hours at 50°, the shortest mode (Vario Speed) is 1 hour 20 minutes.

Rinse program

When loading the machine gradually, this mode is used to rinse dishes. The process is convenient for those who do not cook often. You can fill the device gradually over 1-2 days.

Self-cleaning program

This program is used for hygienic cleaning of parts such as:

inner chamber;
sprinklers;
sprinkler tubes.

It can be turned on without the presence of dishes, using citric acid or ordinary dishwasher detergent. The program is started with an empty device, then 1 cycle is started at a temperature of 70 degrees. Further rinsing occurs at the same temperature. Drying is not done. The chamber, water preheating container and water distribution system are completely cleared of bacteria.

Rinse in three steps

With this function, tableware is rinsed 3 times, thereby completely rinsing off the detergent. The cycle lasts 12 minutes.

Variable wash program

When it starts, the dishes are soaked and washed in intensive mode in different compartments at once. The function helps to save water without affecting the quality of cleaning.

Intensive wash

If cutlery and dishes are heavily soiled, intensive washing will be required. In this mode, the dishes are first pre-soaked and then washed at a temperature not exceeding 70°. Afterwards, 4 rinsing cycles and drying are started. All procedures last within 2-3 hours.

Economical

The mode is aimed at saving water and electricity. It is used for non-greasy and not very dirty dishes. After switching on, it is rinsed, then washed at a temperature not exceeding 46°, then rinsed twice and dried. This takes 15-20 minutes.

Drying

Drying is carried out immediately after all procedures. There is the usual drying of dishes with warm air currents. Another method is condensation, in which drops of water evaporate, transform into condensate, settle on the walls and flow down. Enhanced drying occurs due to the fact that due to the pressure difference inside the apparatus, independent movement of air flows occurs.

Fast

The quick wash program effectively washes dishes that are not very dirty. To activate it, the dishwasher heats the water no higher than 45°. Some models perform this procedure with cold water. In most cases there is no drying. The quick wash is not intended for very dirty cutlery, as it will not wash it. It is recommended to turn it on for glassware. Can be used in combination with other programs. For example, instead of a pre-rinse mode, because there is no need to heat the water. As a result, electricity consumption will be insignificant.

The Quick Wash program may be called differently:

Short program;
Express;
Eat-Load-Run (Eat-loaded-washed).

For dishwashers from different manufacturers, it lasts for different times from 20 minutes to half an hour.

Normal

In this program, before the dishes are washed, they are rinsed. At the main stage, the water is heated to 65°, then the cutlery is rinsed and dried 3 times. This takes 1.5 hours.

The final stage of machine operation

After washing is completed, the dishwasher drains the used water down the drain and begins to dry the dishes. As soon as this process is completed, a signal sounds and the device stops working. There are indicators on the control panel that indicate when work is complete. After a complete stop, the device should be turned off. Experts do not advise taking out the dishes right away; you need to wait 15 minutes. Since drying occurs under the influence of hot air, it may be hot. For quick cooling, you can open the door slightly.

TOP 5 Hansa built-in dishwashers

ZIM 688 EH

A modern built-in dishwasher with convenient electronic controls, a bright display and a delay timer from 1 to 24 hours.

The machine has extra drying and extra rinsing functions . A partial leakage protection system will ensure safe operation of the dishwasher throughout its entire service life. The dishwasher is equipped with a rinse aid and salt sensor.

The spacious box for dishes is equipped with holders for glasses, folding guides for plates, and a separate compartment for cutlery . Additional options - delicate cleaning of fragile dishes, pre-soaking, 2 automatic programs.

Technical specifications:

box capacity – up to 14 sets;
washing, drying, energy efficiency – A, A, A+++;
noise level – 45 dB;
resource consumption per cycle – 10 l, 0.83 kW;
basic washing programs – 8, 6 temperature modes;
power – 1,930 kW.

pros

indication beam on the floor;
sound notification.

Minuses

no child protection;
no automatic 3 in 1;
no half load option;
no water transparency sensor;
there is no automatic determination of water hardness level.

ZIM 4677 EV

Dishwasher with electronic control, full protection against leaks and water overflow AquaStop and economical condensation drying.

The machine has a half-load option, a delayed start timer for the selected program for 1-24 hours, several automatic programs, and an economy mode..

Also, the dishwasher is equipped with an indication of the presence of regenerating salt and rinse aid. The crockery box is made of high quality stainless steel, there are holders for glasses and a separate container for cutlery.

Specifications:

maximum box load – 10 sets of dishes;
noise level – 47 dB;
drying, washing, resource consumption – A, A, A;
power – 1,900 W;
resource consumption – 0.83 kW, 9 l;
6 main programs, 6 temperature modes.

pros

ergonomic display;
convenient control.

Minuses

there is no indication of the end of work - the beam is on the floor;
no water hardness sensor;
no child lock.

ZIM 476 H

The Hans dishwasher is equipped with an ergonomic display indicating time, mode and water temperature. Control type – electronic, drying – condensation. There is an indicator of the presence of regenerating salt to soften the level of water hardness and rinse aid.

The spacious box for dishes has 2 baskets with height adjustment, a compartment for cutlery and holders for glasses . Additional functions include half load, a delay timer for 3-9 hours, and full protection against leaks AquaStop.

Specifications:

capacity – up to 9 sets of dishes;
noise level – 47 dB;
basic programs – 6, 5 temperature modes;
drying, washing, energy efficiency – A, A, A++;
power – 1,930 W;
water and energy consumption per cycle – 0.68 kW, 9.5 l.

pros

automatic means 3 in 1;
audio notification about the end of the cycle;
12 month warranty.

Minuses

no automatic recognition of water hardness level;
no child lock.

ZIM 676 H

A dishwashing machine with a powerful inverter motor, which will ensure long-term operation of the device and minimal noise levels.

Convenient electronic control allows you to quickly select the optimal mode for cleaning dishes with any degree of soiling. Dish drying type – turbo .

Hansa ZWM4577WH

This is a floor-standing, free-standing, electronically controlled device that can hold up to nine place settings. The dishwasher is equipped with five programs and five temperature settings, as well as Aquastop protection.

Control Panel

Controlling the device involves pressing the appropriate buttons and their combinations.

Buttons and indicators:

signal and power on/off button;
signal about the need to fill the compartment for salt and rinse aid;
signal for switching on the half load function;
mode selection buttons and LEDs for them.

Modes:

The normal cycle is to wash lightly soiled dishes without dried particles. Duration: two hours.
Intensive mode - allows you to wash strong, even dried stains. Cleaning duration is 155 minutes.
Eco mode - suitable for washing fragile materials such as glass or porcelain. Cycle duration is 160 minutes.
Express - a short one-hour cycle, suitable for lightly soiled items that can be dispensed with without drying.
Rapid is a very fast half-hour program that is suitable for light soiling, without the need for drying.

TOP 5 freestanding dishwashers Hansa

ZWM 654WH

A modern Hans dishwasher with excellent assembly and a stylish design that will harmoniously fit into any kitchen interior. The model has a spacious box for dishes that can easily wash up to 12 full sets of dishes. The manufacturer has equipped the machine with a child lock mode, complete protection against water overflow and AquaStop leaks.

Another feature of the model is the ability to adjust the height of the basket for loading large pots, vases and baking trays for baking in the oven.

Drying - condensation. The model has a partial load function and a delicate mode for cleaning fragile dishes (glass and porcelain).

Specifications:

maximum box load – 12 complete sets;
drying, washing, energy consumption – A, A, A+;
5 basic programs, 5 temperature modes;
resource consumption per cycle – 12 l, 1.03 kW;
noise level – 49 dB;
power consumption – 2,100 W.

pros

rinse aid and regenerating salt indicator;
guides for plates, holders for glasses.

Minuses

no ice display;
there is no automatic determination of water hardness level;
There is no water transparency sensor.

ZWM 616 IH

Stylish dishwasher with an innovative motor, condensation, economical drying and a spacious box for dishes.

The equipment has a useful child protection option and AquaStop leak protection. For effective cleaning of fragile and delicate items, a delicate mode is provided.

Also, the model has a pre-soaking function . The machine has full protection against overflow and water leaks, as well as an indicator for the presence of rinse aid and regenerating salt. The utensil box can be adjusted in height to make maximum use of the entire space.

Specifications:

maximum capacity – 12 sets of dishes;
drying, washing, energy consumption – A, A, A++;
energy and water consumption – 0.98 kW, 11.5 l;
power – 1,950 kW;
basic programs – 6, 5 temperature modes;
noise level – 49 dB.

pros

audio notification about the end of the program;
partial load.

Minuses

no display;
no child lock option;
no delay timer;
There is no water purity sensor.

ZWM 416 SHE

The Hansa dishwashing machine is equipped with a complete AquaStop water overflow and leakage protection system . The dish box is made of dense stainless steel, has folding plate guides, 3 compartments for dishes and holders for glass glasses.

Drying - natural type, condensation . Additional useful options that make dishwashing easier are half loads and gentle cleaning of fragile and delicate items.

Specifications:

box loading – up to 10 sets of dishes;
power – 1,930 W;
consumed resources – 9.5 l, 0.87 kW;
noise level – 49 dB;
drying, washing, energy efficiency – A, A, A++;
basic programs – 6, 4 temperature modes.

pros

ergonomic display;
musical notification about the end of the cycle;
3 compartments for storing dishes.

Minuses

no delayed start timer;
there is no automatic determination of water transparency;
no pre-soaking;
no child lock option;
no interior lighting.

ZWM 407 IH

The Hans dishwasher is in the budget price segment. This equipment is distinguished by a powerful motor and high build quality. The machine has simple electronic control, a program auto-start delay timer, and an AquaStop protection system.

Dish drying type – condensation, partial load option available.

Basic and special additional programs - economy, intensive, pre-soaking, gentle cleaning of fragile dishes made of crystal, porcelain and glass, regardless of the degree of contamination. After washing, there are no streaks left, and furthermore, scale formation is prevented.

Necessary maintenance

In order for any mechanism to be in excellent working condition for a long time, it must be properly cared for.

High-tech and modern Bosch dishwashers also require maintenance. The status of their individual devices should be constantly monitored.

No matter how strange it may sound, the dishwasher also needs to be washed, its chamber dried with napkins, filters and sprayers cleaned, grease and scale removed

You can find comprehensive information about caring for the devices of your specific Bosch dishwasher model in the instructions for this unit:

Rocker arms. Scale or grease found on their surfaces is a reason to run an intensive washing cycle without loading, but with detergents.
Filters. The condition of the filters must be checked after each operating cycle. Large contaminants are removed, and crayons that clog pores are washed off with hot tap water. If this is not done, dirt may cause the drain pump to block. And repairing the unit will require money and time.
Sprinklers. To prevent the quality of washing from deteriorating, the sprinklers must be periodically removed and washed with hot running water to remove food residues and scale.

If you strictly comply with all the requirements and operating conditions prescribed by the manufacturer, the service life of your equipment will be as long and efficient as possible.

Dear Customers, Before plugging in the cookware cord...

Page 2

Image
Text

Dear customers,

Before you plug the dishwasher into an electrical outlet and

turn on the device, be sure to read the entire instruction manual

operation and installation. The instructions it contains will help reduce

risk of personal injury and damage to the device.

Machine documentation should be kept in a safe place for correct

operation and seeking help if necessary.

These operating instructions have been prepared for

devices and the individual features described herein may

do not touch your dishwasher.

Features of equipment from Hansa

The German brand appeared on the market in 1997. Before that, the products of the company, which appeared in 1957, were sold under a different brand. These were first gas-coal, and then gas and electric Wromet stoves.

The products of the East German company were known in all corners of the USSR. After the collapse of the socialist camp, the manufacturer began to face difficult times.

In order to survive, the company begins to develop fundamentally new equipment for itself - built-in household appliances of its own design. It became the basis for future products. Today these products are successfully sold in 22 countries around the world.

The brand's products are distinguished by functionality, economy and high quality. This is authoritatively confirmed by numerous awards and the consistently high demand for Hans household appliances.

The company, which subsequently began producing products under the Hans brand, initially specialized in gas stoves. The decision to expand her range was very successful for her

The brand's range of dishwashers is very wide.

The manufacturer offers three types of devices:

Built-in. The device is placed in one of the compartments of the kitchen unit, and the facade is hung over the front panel. The main advantage is maintaining the uniformity of kitchen surfaces.
Freestanding. They can be built into a set, but without hanging the facade, or installed separately. Slightly more convenient to use, since the control panel is located on the door.
Tabletop. The most compact models are the size of a microwave. Can be installed literally on the countertop.

Free-standing machines have a capacity of 9 to 12 sets of dishes, built-in varieties are larger, they are designed for 10-14 sets. Tabletop cutlery holds the least amount of space—there are a maximum of six sets of them.

The dimensions of the equipment also vary. Hansa produces two main types of devices: narrow with a width of up to 0.45 m and full-size with a width of 0.6 m.

A built-in dishwasher is perhaps the best solution for the kitchen. It fits perfectly into the interior design without disturbing its unity

The manufacturer positions its devices as economical - most of them are produced with energy consumption class A and higher. The quality of dishwashing is also excellent, which is confirmed by the cleaning class A assigned to the equipment.

All devices from Hans have a set of basic programs:

washing heavily soiled dishes;
washing kits with medium level of soiling;
accelerated mode for cleaning lightly soiled dishes;
rinsing kits;
drying.

This number of basic programs is quite enough for the normal operation of the dishwasher. However, the manufacturer has developed several additional modes that make operating the unit more convenient.

This is, for example, a special cycle for washing pans and pots that are too dirty with grease. This is an eco-program using special bio-active additives that work at low temperatures.

The interior space of each Hans dishwasher model is organized as rationally as possible. Thanks to this, the equipment capacity is impressive

A special regime has also been developed for fragile dishes, which involves gentle washing. Other functions are also provided.

Delayed start makes it possible to activate the machine without direct contact with it, which can be very convenient. For example, if you plan to put the device into operation at night, when a lower electricity tariff applies.

Among the features of the machines, it is worth mentioning the presence of a 3D wash . Hans's designers have developed an innovative water spray system consisting of three independent levels.

The lower and middle elements simultaneously rotate in different directions, spraying the cleaning solution. Their design is such that the streams do not intersect and do not change each other’s trajectory.

At the same time, an additional upper nozzle also operates, spraying detergent on all the dishes located at different levels of the basket. Thanks to the coordinated work of the three-level system, the quality of kit laundering is significantly improved.

Hans engineers have developed a 3D wash that features three independent levels of water spray. This greatly improves dishwashing efficiency

Another feature of Hans’ devices is the presence of a third Maxi Space . The container is designed specifically for cutlery. Thus, the developers managed to optimize the internal space of the washing chamber.

In addition, spoons and forks in a special basket are washed much better and dried faster than if they were in a common compartment.

Users are pleased with the effective protection system implemented in equipment from Hans. First of all, this is the Aquastop system , which prevents possible leaks. A sensor system monitors the appearance of moisture inside the housing; if this occurs, the water supply is turned off.

The devices are equipped with a built-in electrical safety system, and some models have full child protection.

The manufacturer offers two options for connecting its equipment: to hot or cold water. It may seem that the first is more economical. However, one should not discount the quality of heated water supplied to apartments. It contains more contaminants than cold ones. This will lead to rapid failure of the filters and heating elements of the dishwasher.

Connecting the dishwasher to hot water may be justified if there is a water heater at home. But then the costs of its operation will increase

Hans devices are equipped with internal LED lighting , which is very comfortable. The lighting turns on automatically when the device door is opened.

A pleasant bonus is the low noise level. Thanks to the use of special technologies, it is about 45-47 dB. The manufacturer assures that such a quiet machine will not disturb the owner’s peace, even if the kitchen in his house is combined with the living room.

The manufacturer offers a special tray for placing cutlery. Its use significantly improves the quality of their cleaning and facilitates the loading procedure of the machine.

It is worth noting the shortcomings of the brand, which are certainly present. Among the most significant, users noted problems with the service. Hans centers are not located in all cities, and where they are present, it is not always possible for a specialist to visit your home.

Often, the owner of “problem” equipment has to take it far for repair, which is very inconvenient; go and fix it yourself.

In addition, many users talk about the low quality of drying washed dishes. Moreover, this is not a problem with just one, but with many Hans models.

Among the disadvantages, owners also include parts made of fragile plastic, which are equipped with some units. There are also examples with low build quality.

Conclusions and useful video on the topic

Features of Hans dishwashers:

Hansa brand dishwashers delight customers with good functionality, good quality and at the same time low cost. They belong to the middle price segment.

The manufacturer managed to create a very practical technique that meets all user needs. The owner does not have to overpay for incomprehensible functions that are unlikely to be useful to him. Therefore, despite some shortcomings, dishwashers from Hans are in great demand.

Are you looking for an inexpensive and high-quality dishwasher for your home? Or do you have experience using a unit from Hansa? Tell our readers about the specifics of operation and maintenance of such devices. Share your personal experiences and ask questions - the comment form is located below.