Error code on the Indesit washing machine f06

If error code F 06 appears on the display of the Indesit electronic washing machine, you can try to figure out the problem yourself. This error means that there are problems with the controls and the machine does not respond to commands.

The electromechanical model SMA Indesit displays error F6 by flashing the “Additional rinse” and “Soaking” indicators. The “Quick Wash” - “Super Wash”, “Ironing” - “Dirty Laundry” lights may also be on. The user may notice that the Lock indicator is blinking.

What to do and how to restore the machine's operation?

What to do to fix the problem

You can solve the problem and eliminate the F6 error in several successive steps. You need to immediately decide what happened to the Indesit washing machine.

The machine does not respond when turned on

Check that there is electricity in the room and that the traffic jams are working properly.
Check the outlet and power cord with a multimeter. If external damage is obvious, replace the wire.
If the machine is connected via an extension cord, inspect it for defects.
Check the functionality of the buttons and control module. If any violations are visible, then you cannot do without the help of a professional technician. You may need to replace the Start button or triac.

A video about replacing the control module will help you understand the intricacies:

Random blinking of indicators

To remove error F06, unplug the washing machine and reboot for 15-20 minutes. If after turning on the error did not reset, and the code was displayed again, then check the wiring. In some Indesit models, wires come into contact with internal parts, which leads to their malfunction.

What to do in this case, how to fix everything? Check the cable yourself with a tester for damage. If necessary, replace it.

Check the capacitors as shown in the video, perhaps the problem lies there:

The washing machine turns on but does not start washing

How to fix the problem and return the machine to working order?

Check the loading hatch. If it is not closed tightly, the protective mechanisms will not allow water to run.
Make sure the door is energized.
The current is flowing normally, but the hatch is not blocked? The locking device needs to be replaced.
Observe how water flows into the tank. Are you hearing any extraneous sounds or is there complete silence? This means that water flows with difficulty, and there is nothing to do the washing with.

When the Indesit washing machine shows error F06 on the display, the main thing is to pay attention to the repair. As practice shows, you can troubleshoot problems yourself.

Error F06 in the Indesit washing machine - control failure, Error code on the Indesit washing machine f06.

What to do and how to restore the machine's operation?

Design features of Whirlpool washing machines

Structurally, Whirlpool washing machines are not too different from similar equipment produced by other well-known brands. The US manufacturer offers two types of washing machines:

Thanks to this, the user has the opportunity to find a convenient solution that will best satisfy his needs. As a rule, it is possible to understand some technical features of a particular model only if you have drawings, and then only in the context of the location of certain elements or parts inside the device.

There are no serious differences between these types of machines - they can only be in the technology of loading laundry.

What to do to fix the problem

You can solve the problem and eliminate the F6 error in several successive steps. You need to immediately decide what happened to the Indesit washing machine.

The machine does not respond when turned on

A video about replacing the control module will help you understand the intricacies:

Random blinking of indicators

What to do in this case, how to fix everything? Check the cable yourself with a tester for damage. If necessary, replace it.

Check the capacitors as shown in the video, perhaps the problem lies there:

The washing machine turns on but does not start washing

How to fix the problem and return the machine to working order?

When the Indesit washing machine shows error F06 on the display, the main thing is to pay attention to the repair. As practice shows, you can troubleshoot problems yourself.

Article source: https://cosmo-frost. ru/oshibki-stiralnyx-mashin/indezit/oshibka-f06-v-stiralnoj-mashine-indezit/

Error f06 Indesit - Indesit washing machine and error code f06 with explanation, Error code on the Indesit washing machine f06.

Control board failure

Error indication F06 may indicate that the electronic module, which in the Hotpoint Ariston model is located closer to the rear wall, has failed. Repairing this part requires skill, special equipment and spare parts.

To eliminate this error, burnt-out elements are first detected. In most cases, it is recommended to contact a service center technician. Replacing a module has its own peculiarities. After removing and replacing the part, software installation (firmware) is required.

Decoding

The Indesit f06 code indicates a control error. The command buttons on the panel do not respond to user actions, Indesit does not start the wash cycle. There are several reasons, and to restore the working capacity of the washing machine you will have to perform a series of sequential measures.

In some cases, the Indesit f06 error appears due to the door not being tightly closed after start-up. The protective circuit issues a command to prohibit operation, and the washing stops. If the problem cannot be resolved by tightly slamming the hatch, check the microswitch of the locking connection (locking device).

Closing the door lock (hatch locking device) of the Indesit washing machine

Methodology

The resistance between the neutral contact and the rest is measured. When testing a working device, the multimeter will show 0 or ∞ (closed/open). Does not correspond, changing the lock cannot be restored.

What to do

Restart SMA

A standard procedure recommended when complex household appliances equipped with electronics fail.

Method: unplug the power cord from the outlet, pause for 20 minutes, and turn on the washing machine again. If the result is negative, continue searching for the cause of error f06 Indesit.

The idea is that the failure of electronics to obey user commands is caused by circuit failures. This occurs during voltage surges, sudden short-term shutdowns, interference (nearby power lines, powerful transmitters), and stray currents. This simple action in 40% of cases helps to eliminate washing machine error f06 - after all, in most high-rise buildings, grounding is not provided in apartments.

Check the power supply parameters

The manufacturer Indesit guarantees the trouble-free functioning of the AMS, provided that it is supplied

220–240 V/50 Hz. Inconsistency between U or f values is the cause of error f06. It is easy to verify the quality of the energy supply by turning on any imported household appliance equipped with electronics. There are no malfunctions, everything is normal, continue to look for the “culprit” of the problem.

Assess the condition of the power circuit

Error f06 Indesit is called:

Elimination of such defects does not require the help of a professional; error f06 with Indesit can be removed independently.

Perform loop diagnostics

Assess the condition of the wires in the Indesit washing machine

Test the book. "Start"

Power button (ON-OFF) Indesit

A broken switch is the reason for the lack of control of the washing machine, error f06. Tested by pressing: closing the contacts indicates serviceability. If the multimeter shows R=∞, replace it.

Inspect the boards

Repairing Indesit electronics yourself will only add problems. Diagnostics of the control boards (the “brain” of the washing machine) and the display panel are carried out on a specialized stand that simulates the operation of the AMS in various modes. Without circuits, equipment, or practical experience, testing modules at home is an unpromising activity.

It’s also not worth following the advice of “nugget repairmen”. In Indesit washing machines of different years of manufacture and series, the circuits and layout of electronic boards are different. And it’s not a fact that a hint from the outside will help remove error f06 and not harm. According to service technicians, up to 80% of users completely destroy their boards by unprofessional intervention in the electronics of the SMA; it is no longer possible to restore.
Expert opinion

What to pay attention to

Error f06 cannot be removed by the measures taken, contact a workshop certified by the manufacturer. Diagnostics at the stand and professional troubleshooting will cost several times less than buying a new board.

If you have experience in correcting errors F06 of Indesit washing machines , write in the comments to this article, we will try to consider your option and analyze it in detail in this or one of the following articles . Send photos and videos with comments and descriptions.

Article source: https://fixbroken. ru/oshibka-f06-indezit/

Error F06 on the Indesit washing machine, Error code on the Indesit washing machine f06.

Error F 05 – We fix it ourselves.

Software error.
Electronics, like any device, can make mistakes, most often this happens if the light blinks during operation. To fix the problem, you need to restart the washing machine software. To do this, turn off the washing machine using the power button and unplug it from the outlet for 5 minutes. After 5 minutes, turn on the power and press the “on/off” button. If the error was false, code F 05 will no longer appear.
Filter clogged.
A fairly common problem, since few people read the instructions or have simply forgotten what is written there. Foreign objects from clothing pockets, animal hair, and even human hair often get into the filter. All the clog makes it difficult to drain the water. You just need to remove the blockage, but to do this you need to drain the water from the washing machine tank through the emergency drain or by any means. The emergency drain is located in the lower right corner of the washing machine. Unscrew the drain filter and remove foreign objects. If error F05 no longer appears, then the cause has been resolved.
Prepare a rag, as water will still spill on the floor; there is always water left in the filter!
Read also: Why does the washing machine fill with water and immediately drain: repair methods
Or read the article Draining water if the washing machine breaks down.
Clogged drain hose
. Often debris gets from the pump into the drain hose and blocks the water from draining. Before clearing the blockage, drain the water as described above. Next, you will need to disconnect the hose from the washing machine and drain and clear the clog. Reconnect the hose to the machine and sewer in reverse order. To check, run a short program and wait until the Hotpoint Ariston washing machine program completes. If the error no longer exists, then the problem is solved.
Sewer blockage.
A blockage in the sewer can also be the cause of error F 5 on the Ariston SMA, since the washing machine does not understand that the filter, hose or sewer is clogged, it doesn’t care. The reason remains the same, the water does not drain. It is not difficult to check this; disconnect the drain hose from the sewer and lower it into the sink, bathtub or toilet. Run the drain or spin program separately. If the error disappears, then you have a blockage in the sewer.
Important! Depending on the connection, plug the hole from the hose with a rag.

I also recommend that you read the instructions for your Hotpoint-Ariston washing machine, section “Troubleshooting”. The instructions contain the most common faults that you can solve yourself. If the recommendations do not help, and error F 05 still interferes with the operation of the Ariston washing machine, call a specialist for professional repair.

Code identification

Is it possible to deal with the problem with your own hands and return the washing machine to working capacity? To solve the problem, you need to figure out what this error means. Code F06 indicates a problem in the control of the washing machine, as a result of which the machine does not respond to user commands or does not start washing. That is, the washing machine simply does not respond to button presses and does not start the selected mode.

The Indesit machine, which does not have a display, displays an error by flashing the lights. The “Extra Rinse” and “Soak” indicators are lit. The “Quick Wash” and “Super Wash” lamps are allowed to glow. The “Ironing” and “Dirty Laundry” indicators may be on. Also, an attentive user may notice the blinking of the “Lock” LED.

What to do when faced with such a problem? How can I return my Indesit machine to working order? Whether it is possible to cope with the breakdown yourself, or whether you will have to call a specialist, we will analyze further.

Diagnostic and repair work

Characterized by rather complex design features, the washing unit can break down at any time. The main causes of malfunctions of a washing machine of a given brand can be very different.

After finishing the wash, the water remains in the machine

Who hasn’t encountered such a problem when during the washing process the machine freezes and water remains in the tank? There are the following reasons for this behavior of washing devices:

You can start repairing household appliances yourself after finding out the cause of what happened, as well as why the household appliance behaves this way. If stagnant water occurs, you should try to quickly get rid of it using an emergency hose located near the drain filter. After this, you can begin searching for defects, for which you need to perform several steps:

Refuses to turn on

How to correct the situation if the user’s attempts to turn on the automatic washing machine remain unsuccessful? What if the washing machine refuses to start?

First of all, you should check whether there is electricity in the apartment; perhaps the power in the house is turned off. See if the plugs are knocked out. You can also check the serviceability of the outlet itself and the power cord with a multimeter. If defects are noticeable upon visual inspection of the power cord, the cord must be replaced.

If the washing machine is connected to the network through an extension cord, it is worth inspecting it for damage. Next, you should check the serviceability of the buttons themselves on the control panel. If everything above is in order, you will have to inspect the main control module of the washing machine. If defects or broken connections are clearly visible on the board, you need to invite a professional.

It will not be possible to repair the “brain” of the washing machine without certain knowledge and experience; you can only ruin the part, and this will lead to higher repair costs.

The technician will diagnose the control module, replace the triac if necessary, solder the tracks, etc.

How to test a tachometer?

If you decide to carry out further manipulations, we work strictly according to the instructions. We mark all the wiring of the electric motor with a marker or take a photo with our phone. This will avoid errors when reassembling the Whirlpool washing machine.

It is important to check the position of the latches and the integrity of the contacts. If you see a loose or loose fastener, you need to restore it in place. What to do if there is no obvious damage?

The next step is testing the tachogenerator. There are two ways to check the functionality of this part. First: turn the multimeter on to ohmmeter mode, apply the probes to the contacts. Normally, the sensor resistance is 60 ohms. Second: current measurement. To do this, set the voltmeter mode on the tester, connect the probes to the contacts and accelerate the motor with the second hand. If a figure of 0.2 V appears on the device, the sensor is in good condition.

Replacing a damaged element will not be difficult. You should completely disconnect the wiring and remove the cover of the part, secured with a conventional latch. Then unscrew the fasteners, remove the tachogenerator and install a new one in its place.

Lights flash randomly

In some cases, a simple reboot of the equipment helps to eliminate the F06 error. Unplug the washing machine for about 20 minutes. If this manipulation does not help, and the washing machine gives an error again, it is better to check the wiring. In certain Indesit models, the wires pass in close proximity to the internal parts of the machine. Such close proximity leads to their damage. You can check the wiring with a tester, and if it is damaged, replace it yourself.

It makes sense to check the capacitors on the control board of the washing machine. Sometimes, this behavior of the “home assistant” is caused by burnt-out capacitors, namely 10v680uf, 10v1000uf, 10v470uf. Diagnostics of elements and their replacement will help eliminate the problem.

Can't start washing

It happens that error code F06 appears after the wash has started. What to do in this case? First, you should check whether the drum door is closed tightly. If the hatch is not completely closed, the protective system will not allow water to enter the drum, but will pause the wash, displaying error F06. It may be necessary to replace the UBL to fix the problem.

Diagnosis and replacement of the locking device is quite simple:

Before disconnecting the contacts, take a photo of the wiring diagram!

The tester switches to resistance measurement mode. The probes of the device are applied to the neutral contact and phase. If a three-digit number is displayed on the multimeter screen, it means the lock is intact. Afterwards, the probes are applied to the neutral and common contact. If the device shows one or zero, everything is in order. A faulty UBL must be replaced; repairing the lock is impossible.

Probably, code F06 appears because the machine cannot draw water, and there is simply nothing to wash with. Then make sure that your water is not turned off or the shut-off valve is not closed. In most cases, you can fix the error yourself if you pay close attention to the “symptoms” of the breakdown.

How to detect errors F 05 and others in the Ariston washing machine

The Hotpoint Ariston washing machine is equipped with a special device through which you can carry out independent diagnostics and identify the problem of breakdown. The purpose of such a service tester is to investigate the breakdown of each component in the equipment, as well as analyze the general condition. This can be done quickly and, moreover, you can get only reliable results. Thanks to this built-in function, you can carry out the process without contacting a specialist and spending additional money.

To run the test and carry out the diagnostic procedure, you will need to perform a number of actions

First, the SAT diagnostic key is connected, which helps start the testing program.
To connect the device, a special connector is provided on the back of the equipment; after connection, the product begins to glow with a green or blue lamp. If the light is red, this means that data is being exchanged between the diagnostic device and the direct controller in the product control module.
Next, the testing program is launched, which requires that the device be connected to both water and electricity. It is important that there is no water inside the tank and that the door is completely closed. This is the only way to obtain reliable data.

The program switch is placed in the initial position and the automatic test button is pressed, which must be held for a while until a sound signal appears.

Code identification

Refuses to turn on

How to correct the situation if the user’s attempts to turn on the automatic washing machine remain unsuccessful? What if the washing machine refuses to start?

It will not be possible to repair the “brain” of the washing machine without certain knowledge and experience; you can only ruin the part, and this will lead to higher repair costs.

The technician will diagnose the control module, replace the triac if necessary, solder the tracks, etc.