Error F15 of the Atlant washing machine: what does the F15 code mean, how to detect the problem and fix it on your own?

Domestic consumers are well familiar with TM Atlant household appliances produced in Belarus.

This company has been producing washing machines for several years now, improving production and constantly expanding the model range.

Automatic devices have proven themselves to be reliable equipment at an affordable price. But, like other washing machines, Atlantas can malfunction.

One of the possible situations is error F15 on the display of the Atlant washing machine.

Decoding the F15 code

Failure code F15 almost always appears immediately after turning on the device. If a failure occurs, Atlant no longer responds to pressing other buttons.

What the F15 fault code on the display means depends on whether the machine is equipped with the AquaStop option. In devices that have it, this code indicates that the aquastop has been triggered due to a leak. And in cars that do not have this option, F15 indicates a malfunction of the pressure switch.

In washing machines that do not have a display, the analogue of F15 is a signal from a certain combination of indicators on the control panel. Which lights come on during such a failure depends on the model.

In Atlant washing machines that belong to the OptimaControl line, problems are indicated by the lighting of the following indicators:

"Prewash".
"Wash".
"Rinsing".
"Water stop."

In washing machines from the SoftControl series, an analogue of F15 is the following combination of light bulbs:

"Wash";
"Rinsing";
"Water Stop";
"Spin."

When the F15 appears, you should analyze the current situation, and in some cases it is even possible to solve the problem on your own.

Error F13 - when you can fix it yourself

Failure of the control board (electronic controller) or indication. If code F13 appears for the first time, try unplugging the washing machine from the socket. After 10 - 15 minutes, plug it in again and try to run the previous program. Perhaps there was a one-time failure of the “brains” of the washing machine, and after a reboot it will work normally.
Weak contacts. Check all wiring connections from the drying temperature sensor to the electronic controller. Perhaps, due to vibration during operation of the machine, the tightness of the connections has been compromised and needs to be restored.

If the advice for correcting the error yourself does not lead to success, then a breakdown has occurred and your Ariston washing machine requires professional repair.

Cause of the problem and solutions

Code F15 requires checking the condition of the washing machine. Not in all cases it indicates a serious breakdown.

Leak not related to the washer

The activation of Aquastop does not always indicate a breakdown of the Atlant washing machine. A situation is possible when water gets onto the tray of a device equipped with the Aquastop function, not from the washing machine itself, but from nearby water supply lines or as a result of accidentally overturning a container with water.

If the problem is not in the washing machine, you need to fix the leak yourself or by contacting a plumber.

Wrong detergent choice

only the product that is intended for automatic SMA should be poured into Atlant machines . If an unsuitable preparation, which is oriented towards manual processing, was placed in the powder receptacle, a lot of foam will begin to form during washing.

As a result, water with foam may get into the pan, which will trigger the Aquastop. The solution to the problem is to use for washing only those washing powders and gels that clearly indicate that they are intended for automatic washing machines.

Too much powder

Too much powder per wash does not always lead to better washing.

Not only will the detergent dissolve and rinse out of things worse , but it can also cause Aquastop to trigger.

Washing curtains made of tulle, wool and other porous fabrics can also produce an unexpected effect with large foam formation. For such laundry, the dose of powder should be lower.

The solution to the problem is to strictly adhere to the dosage of detergent recommended by the manufacturer and take into account the type of material placed in the drum.

One-time failure

In rare cases, it is possible that a failure with F15 is caused by a power surge or an accidental coincidence. To check a possible situation, you need to disconnect the device from the network for a quarter of an hour, and then turn it on again .

If the problem does not go away after rebooting, you will have to move on to more serious diagnostics of the condition of the washing machine.

Water leak

F15 - information that was transmitted through the control module from Aquastop, and it indicates a leak. The cause can be almost any node that is connected directly to water. These could be hoses, pipes, cuffs, tanks, etc.

To analyze the problem, you must first inspect the visible part of the hoses and the manhole cuff. If everything is in order with these parts, you will have to partially disassemble the body of the Atlant washing machine and sequentially inspect all components that have contact with water.

By identifying the washing stage at which the error occurred, you can narrow down the search for the leaking node. If code F15 appears when drawing water, then you need to inspect the fill hose, pipes, and possibly the tank itself.

If a leak is detected during the washing stage, you first need to inspect the fill/drain pipes, the hatch rubber and the drum. When a leak occurs during draining, the following components are subject to diagnosis:

drain filter;
drain hose;
pipes;
water pump.

Breakdown of the pressure switch

Failure of the water level sensor is manifested by stopping operation and issuing F15. In this case, there are no signs of leakage.

If the pressure switch is stuck, the control module does not receive objective information from this unit . The solution to the problem is to inspect the condition of the sensor.

To do this, you need to gain direct access to the unit, which is achieved by partially disassembling the washing machine. If repair is possible, then the pressure switch chamber is cleaned. If it breaks, the pressure switch is replaced with a new one.

Failure of the control module

If the control module fails, the Atlant must be repaired with the replacement of elements and re-soldering of the tracks. As a rule, with F15 the problem concerns the pressure switch or Aquastop circuit. If there are extensive burns and damage, the board is replaced with a new one.

The Aquastop sensor is broken

If the Aquastop sensor fails, it may send unreliable signals about water overflow and flooding to the control circuit. If possible, repairs are carried out, otherwise it is replaced with a new one.

Wiring problems

If the wiring in the circuit that turns on the Aquastop or pressure switch is broken, the display may also display code F15. To analyze the condition of the electrical wiring inside the washing machine, it is necessary to open the case and partially disassemble the device. When identifying a damaged area, the entire group is twisted or replaced .

We are looking for other faults

It is rare, but it also happens that water leaks from the tank of the machine through a damaged cuff, a crack in the powder receptacle, or a hole in the tank itself. The main sign indicating a malfunction in the cuff is water streams seeping through the unit door. Damage could occur for two reasons:

the cuff was cut by small sharp objects;
it simply dried out and cracked from long use.

Minor damage to the rubber seal can be repaired using patches used for bicycles and rubber boats. But it will be better if the cuff is replaced with a new element.

Now let's figure out what can happen to the powder receiver. It is not at all necessary that cracks may appear on its body. Here, a lot still depends on the correct installation of this element. If there are any inaccuracies, water may penetrate into the pan, partially flowing out. Everything is simple here - the tray is removed, inspected for integrity and put back in its place. Excessive water pressure is often to blame. To solve the problem, you just need to tighten the faucet a little to weaken the flow of water.

Call a master: where to find and how much will the work cost?

If the problem cannot be solved on your own, you can contact a company that repairs household washing equipment for help. Such companies are widely represented on the Internet.

It is better to give preference to companies that have been operating on the market for a long time and have many positive reviews. The cost of the technician’s work is determined by the company’s price list and the complexity of the breakdown.

On average, MSC prices are:

eliminating leaks - from 1100 rubles;
replacement of the pressure switch – from 1,700 rubles;
repair of the control unit - from 2100 rubles;
replacement and repair of aquastop - from 2100 rubles;
wiring repair - from 1600 rubles.

If parts need to be replaced during repairs, their cost will be charged separately. After the repair, the master gives a guarantee for the work he performed.

How to check an electric motor?

An Atlant brand washing machine may indicate a malfunction with error F9 if there are problems with the electric motor. If there is a current leak to the housing, or the armature is broken, there is nothing you can do, the part cannot be repaired and you will have to replace the unit. And this part is expensive. Of course, theoretically the engine can be repaired. But this is not practical from an economic point of view. Such repairs will cost more than buying and replacing a broken part with a new one.

So, how do you determine that an engine replacement is needed? To do this, the motor must be removed. Disconnect the wires from it, unscrew the bolts and pull the motor towards you. Next you need to find the brushes, unscrew the holders and pull out these parts for inspection. If the brushes are worn out, they need to be replaced. You can tell if the brushes are worn out easily; they will be too short. By the way, always change brushes in pairs. And if: buy only original brushes, otherwise there is a risk of damaging the commutator lamellas and then the cost of repairs will increase significantly.

After this, we open the housing of the device and use the same multimeter to check for leakage on the housing, as well as the motor winding for breakdown. If there are no problems with the brushes or motor windings, and no leaks to the housing are detected, then everything is fine with the motor. We need to look for another reason.

Prevention measures

In order not to encounter the problem of a failure and displaying F15 on the display, it is necessary to take into account the following methods of prevention and prevention of problems in the future:

Use only powders for washing that are designed for automatic processing.
Do not add more powder than recommended by the detergent manufacturer.
The washing machine must be installed according to the rules specified in the instructions for the device.
Reliable communications to the device must be ensured.

Running the test

You don’t have to wait for the diagnostic mode to start automatically, but activate the test on your own initiative. This approach will allow you to periodically carry out preventive checks without leading the problem to a serious malfunction. To start self-testing, you must follow the following instructions:

You can run self-diagnosis on Atlant yourself!

If everything is done correctly, “8888” will appear on the display, and all dashboard indicators will begin to light up periodically. This means that the test mode has been launched and the test has begun. The duration of diagnosis depends on many factors and usually takes at least 15 minutes.

Evaluating the test results is easy. If at the end of the test three beeps are heard, then the system has not detected any problems - everything is working fine. Otherwise, the machine will remain silent and display the detected error code on the screen. Knowing the decoding of the code, you can quickly determine the cause of the failure and fix the problem. If you have any difficulties or doubts, it is better to contact the service center.

Source

Recommendations

When F15 appears on the Atlanta display, advice from washing machine repair specialists can help:

Opening the case yourself is only possible if the device is not under warranty.
Before disassembling the washing machine, you should turn off all communications.
The analysis of possible breakdowns must be carried out from simple to complex.
You should not undertake serious equipment repairs without the knowledge and tools.
Replace parts, if such a need arises, preferably with original ones.

We are looking for other faults

the cuff was cut by small sharp objects;
it simply dried out and cracked from long use.

Minor damage to the rubber seal can be repaired using patches used for bicycles and rubber boats. But it will be better if the cuff is replaced with a new element.

The difficulty comes from cracks that appear in the tank. Here, there will be financial expenses, and free time will be required to eliminate everything. Damage to the tank may occur due to:

sharp foreign objects that for any reason ended up in the drum;
defects caused by the manufacturer;
strong shocks received as a result of transportation and loading.

If a crack is detected, the tank must be replaced. Glue will help in this case, but not for long. You should also know that the tank of the machine is a combination of halves, between which a rubber seal is installed. It is this that can develop a leak from prolonged use. In this case, the machine will have to be almost completely disassembled to carry out repairs.

Most often, water leaks from the machine due to broken hoses. The elements are made of rubber material and wear out quickly. This is especially facilitated by low water quality. It is possible to identify such a problem even when the machine is not working. The hose is carefully inspected, its connection points are checked. If necessary, change the gaskets or the entire element.

If a leak is detected during water intake, which disappears after filling the tank, the problem should be looked for in the pipes connecting the hose and the powder compartment. If necessary, the pipe simply changes.