Instructions and manual for Indesit WISE 87 in Russian

Latest questions

Washing machines Indesit WISE 10
on any program, the Indesit WISE 10 machine shows a problem with the door after several minutes of washing. the door opens and that's it. Tell me what to do?

Newton 04/17/2017 22:25

Check the terminal devices from the heating element to the remote control and only after that it will be possible to say that the module is broken

IntelService 04/17/2017 22:16

Check the motor brushes, then the control board. The repair price does not exceed 2500 rubles.

Master with 25 years of experience 04/17/2017 14:29

Check the brushes on the engine, if they are normal, replace the electronic door lock (ELL). If nothing changes, then the electronic module will be repaired.

domel 04/17/2017 14:28

Is the hatch locked with a padlock before the water starts pouring in? Try opening it. Water is poured into the tank and the drum starts to rotate normally? Is there any increased noise when the drum rotates?

Heating Electrics 04/17/2017 18:05

Good day! In most cases, this occurs due to wear on the motor brushes. It is also possible that the simister for controlling the lock has burned out on the control board. Remove the board and do a visual inspection.

Petr Terentyev Repair of household appliances 04/17/2017 16:27

First of all, check the motor. Dismantle it, ring the rotor and stator. Test the rotor for ground fault using a megohmmeter. Remove the brush assembly. Assess their condition. Assess the condition and wear of the collector assembly. Check the motor connector. Are the contacts oxidized? Check the wiring from the engine to the control unit. Remove the control unit. Check the motor control circuits according to the control unit circuit diagram. It's on the Internet. Next, check the hatch locking device by replacing it with a known good one.

This error is often displayed at the initial stage, sometimes at the end, and very rarely during the operation of the washing machine. The unit does not start washing, the program is interrupted, and the door may not open. And all these negative phenomena are accompanied by a corresponding signal - Door error in washing machines.

Door error in washing machines of various companies

Let's consider more specific actions for SM from leading manufacturers.

Indesit

You can often hear complaints about models from this company that they often break down. We will not argue about the quality of the product, but will deal with the door error code - as the most common problem.

The peculiarity is that the lock located inside the door is thought out rather poorly. The axis holding the hook with the spring pops out from time to time. As a result, the hook cannot lock the hatch in the “closed” position. If this happens, don’t get angry and kick the door. Just follow a few simple steps:

• disconnect the machine from the electrical network;
• remove the water in the washing machine using a garbage filter;
• unscrew the fasteners and remove the door;
• unscrew the screws that secure the parts of the hatch together;
• insert the axle into the place intended for it;
• We perform assembly in reverse order.

Demo mode in Indesit washing machines

This function involves demonstrating the capabilities of the technology. To enter demo mode you need to:

1. Press and hold the power, “start” and “light ironing” keys simultaneously for 5-6 seconds.
2. Wait for the electronic indicator “dEPO” to appear on the screen
3. Press the “Start” button

Control Panel

To disable demo mode:

1. Turn off the program by pressing the “Start” button for 3 seconds.
2. Simultaneously hold down the power, “start” and “light ironing” keys.
3. Wait for the “dOFF” indicator on the screen.

Possible errors and solutions for washing machines

In the event of a malfunction or problems in the functioning of the Indesit Wise 8 washing machine, as well as other models of the Wise series, a code with the corresponding error from F01 to F12 will appear on the screen. Any of these errors is a reason to call a qualified technician, as parts may need to be replaced.

Depending on the information on the display, the following errors can be identified:

• F 01 – an electrical connection of different phases has occurred in the power supply circuit of the drive motor.
• F 02 – a short circuit or open circuit of the tachometer has occurred.
• F 03 – connection of different phases in the temperature sensor circuit.
• F 04 - the error can be caused by a lack of water in the tank, as well as its overflow. Also, the reason for the appearance of this code may be a stuck sensor for automatic drainage of water.
• F 05 – blocking of the drain pump.
• F 06 – malfunction of control buttons.
• F 07 is a protective function that turns on if there is no water after the stage of filling the tank with water is completed.
• F 08 – continuous operation of the heating element relay in the module.
• F 09 – memory error or failure of the EEPROM chip.
• F 10 – malfunction of the water level sensor.
• F 11 - the drain pump is malfunctioning due to a break in its winding or power circuit.
• F 12 – communication error between the electronic and display module.

Compact and spacious Indesit washing machines are high-quality equipment to meet the needs of a modern housewife.

The Wise series models have reduced noise levels, water and electricity consumption, which makes them economical. They do an excellent job with their main task - washing clothes, freeing up a significant amount of free time for you.

How is the signal decrypted?

By the way, on some washing machines it may display the alphanumeric code F 16. The problem means that an error was made when closing the door. For some reason, the hatch is not locked, or the unit’s electronics do not “recognize” the action performed.

Deciphering the problem indicates a probable breakdown of the device blocking the hatch. But we should not rush to conclusions. It is likely that there is no breakdown, and everything that happens is a consequence of a program failure or your personal carelessness.

How is the signal decrypted?

By the way, on some washing machines it may display the alphanumeric code F 16. The problem means that an error was made when closing the door. For some reason, the hatch is not locked, or the unit’s electronics do not “recognize” the action performed.

Deciphering the problem indicates a probable breakdown of the device blocking the hatch. But we should not rush to conclusions. It is likely that there is no breakdown, and everything that happens is a consequence of a program failure or your personal carelessness.

Washing machine Indesit WISE 10 csi characteristics

Door error in washing machines of various companies

Let's consider more specific actions for SM from leading manufacturers.

Indesit

You can often hear complaints about models from this company that they often break down. We will not argue about the quality of the product, but will deal with the door error code - as the most common problem.

The peculiarity is that the lock located inside the door is thought out rather poorly. The axis holding the hook with the spring pops out from time to time. As a result, the hook cannot lock the hatch in the “closed” position. If this happens, don’t get angry and kick the door. Just follow a few simple steps:

• disconnect the machine from the electrical network;
• remove the water in the washing machine using a garbage filter;
• unscrew the fasteners and remove the door;
• unscrew the screws that secure the parts of the hatch together;
• insert the axle into the place intended for it;
• We perform assembly in reverse order.

If everything is fine with the mechanism, but the hatch does not close, you should check the hatch control unit, module, etc.

Atlant

Such machines not only have mechanical latches, but are also blocked by an electronic device. It works from impulses - the plates in the device expand, pressing the lever. Sometimes they wear out and the device needs to be replaced. But first, it is recommended to check using a multimeter.

We also inspect the lock opening and remove any debris that has accumulated there. We check the wiring connecting the lock blocker and the control unit. It is likely that the problem lies here.

The final stage is checking the module for board resistance. It may need to be repaired or replaced completely.

There are also other mechanical problems. To eliminate them, we check certain places:

• We inspect the position of the hinges - the hatch could be warped due to poor installation or long-term use. In these cases, the latch will not reach the lock. We check the evenness of the installation, tighten the hinges to return the door to its normal position;
• we check the handle - if the element is broken, you should remove the door and replace the element;
• latch - it can move due to the fact that the pin holding it falls out. To fix the problem, the lock mechanism will have to be disassembled;
• The plastic guide element is worn out - when the characteristic click of the lock is not heard, the guide should be replaced.

Ariston

It should be noted here that actions with Atlant and Indesit are also relevant for this brand. But they still have their own characteristics. In an Ariston machine, this signal has nothing to do with the door lock. A similar error can occur from poor contacts on the motor brushes.

In this case, you should get to the motor, unscrew its fastenings, and disconnect the wiring connector. Having removed the motor, we check the integrity of the brushes and inspect the wires that power them. It is possible that the brushes are worn out from prolonged use and need to be replaced.

Samsung

On washing machines from this company, not only this error signals problematic issues with the door. Signals de, Ed, de 1, de 2 may appear.

Problems are associated with the following features:

• the hatch is not blocked from the very beginning;
• the door does not open after finishing the wash;
• First the blocking works, then it disappears. The machine “freezes” and produces a corresponding signal;
• the door tongue did not hit the lock;
• The signal may appear and disappear many times during the wash cycle, from five to seven times.

What should be done in such cases? Let's look at the simplest option, when the hatch closed and a click was heard, but the machine signaled a problem. In this case, it is necessary to check and, if necessary, repair the blocking device.

And if the door does not open after the washing process, the problem should also be looked for in this place. But first it is recommended to wait ten minutes. The lock may open automatically.

Features of care

To avoid breakdowns of household appliances, you must follow all the rules specified in the instructions. If the machine is under warranty, proper adherence to the instructions will allow for warranty service and repair of the device at the expense of the manufacturer. Otherwise, warranty repair will be denied.

In order for the machine to serve for a long time without breakdowns, you should follow simple rules:

• do not exceed the maximum established amount of clothes for one wash;
• at the end of work, dry the drum;

Dirt accumulation area

• Regularly clean the detergent compartment;
• use special water softeners;
• Regularly clean the filter, where large particles of dirt and other objects accumulate.

It is important to know! If there are frequent voltage surges in the house, you should additionally install a stabilizer. Sudden voltage surges can lead to burnout of the washing machine elements.

Detergent compartments

How to install an Indesit washing machine

Correct installation and connection of equipment is the key to its proper functioning. If you do not have the necessary skills, you should seek help from specialists.

The installation process involves:

• removing all elements and belts for transportation;
• connecting the water supply hose;
• drain supply and connection to the sewer system;
• connecting the device to electricity.

To prevent the machine from vibrating during operation, it must be installed on a level surface. In many cases, improper installation and connection of the washing machine is the key reason for failure.

Washing machine installation

We fix the problem ourselves

There are several generally accepted rules that will help cope with the problem. They are used in certain situations:

1. The hatch did not close tightly - you need to check, most likely, you did not apply the required force when closing, or something got between the door and the rubber seal that is preventing it from closing. We recommend performing the action again; you should hear a characteristic click.
2. The network voltage has dropped - check. If there is no 200 volts in the network, the hatch lock does not work. But the problem can be solved - a relay is installed that controls the voltage.
3. The hole for the door tongue in the lock is clogged - make sure everything is in order.
4. The hinge fasteners of the door have become loose - as a result, the tongue does not always fit into the lock, and the hatch may not close. You'll have to tighten the fastenings.
5. A failure of the control or display unit has occurred - when the error appears for the first time, simply unplug the machine from the socket, pause for about ten minutes, and turn on the device again. The unit will reboot, it is quite possible that the error will disappear.
6. Poor contact - it is necessary to check the area from the hatch blocker to the unit responsible for general control. It happens that the vibration of the SM during operation is the reason that the contact connections “come off”.