Installation of a Siemens dishwasher: built-in and free-standing. Installation in 3 steps

Siemens dishwashers represent German quality, but in order for such machines to work well for many years, it is necessary to correctly select a place for them and connect them to communications. In this case, the instructions for a specific car model are the first assistant. Even specialists sometimes need to look there, not to mention people who decide to do the installation themselves. In this article we will talk about the features of installing Siemens brand dishwashers; these nuances are few, but they are of great importance.

Features of the selection of components

With the standard installation procedure for a Siemens dishwasher, you can easily use the set of components that come with the machine. But according to installation experts, in about half of the cases non-standard solutions are required, for which you have to purchase additional components. For example, if the inlet hose of a particular dishwasher model is not equipped with an aqua-stop valve, then it will have to be purchased separately.

Be careful! The “aqua-stop” valve for a Siemens dishwasher must be taken either original (from Siemens) or from Bosch dishwashers, but it is not suitable for some Siemens models.

Original components are always more reliable, they will definitely fit, but they are also a little more expensive than substitutes, so it’s up to you to decide what to choose. If you want to save a little money, choose your spare part more carefully. If the length of the standard inlet or drain hose is not enough for you, and you decide to purchase a longer one, then it is also better to take an extended hose from Siemens.

The problem is that this manufacturer, when developing specific models of dishwashers, did not unify many elements, which is why they have hoses with an unusual diameter and non-standard fasteners. This is perhaps the main drawback of dishwashers from Siemens; otherwise, they are reliable, practical and technologically advanced. To install a Siemens dishwasher to the water supply and sewerage system you will need:

water inlet hose;
water drain hose;
shut-off valve (with two, three or four outlets);
filters;
gaskets;
adapters.

This is a common kit that is used for typical water and sewer connections, but other parts may be required. By the way, this is what the instructions for some Siemens dishwashers say.

Pressure reducing valve. If the pressure in your water supply system is higher than 1 MPa, then in order to avoid leaks, hose ruptures and other troubles, a pressure stabilizing valve is installed.
Electric stabilizer. The dishwasher is connected to the electrical network through it if there is a regular voltage drop in such a network or, on the contrary, an increase - this is an option to protect the dishwasher and other equipment.
Additional hose and faucet with filter for connecting to hot water. Some models of Siemens dishwashers have the ability to connect to hot water supply, but there may not be an additional hose; it will have to be purchased separately along with a faucet, filter, adapters and gaskets.

About the installation location and its dimensions

We have decided on the components for the Siemens dishwasher, now we are installing the dishwasher in the countertop and furniture. Even when installing an ordinary dishwasher in furniture, many difficulties can arise, and a separate conversation about the Siemens machine. Let's look at the recommendations of experts regarding the organization of space for a dishwasher and its size.

If you are preparing a place for a fully built-in or partially built-in dishwasher, first carefully measure the model you choose. Do not trust the size information given in the specifications. Measure each protrusion, in addition, allow for a margin of distance from the walls of the niche to the machine body on the left 2 cm, on the right 2 cm, on top 1 cm.
Figure out in advance the installation of fasteners for the facade and a metal sheet to protect against steam (if any), after connecting the communications it will be inconvenient to do this.

For your information! In general, before installing a dishwasher, washing machine, refrigerator or all appliances together, it is better to solve problems with the floor, level and strengthen it seriously and for a long time - this will extend the life of each appliance.

You should not organize a place for a Siemens dishwasher further than 2 m from the connection to the water pipe and the sewer pipe. The point here is not only the length of the hose, but also the fill valve and pump. If the distance is large, the pump will work much less, and so will the valve.

Connect to water and sewer pipe

If the work on organizing the space was successful and you are convinced that the specific model of dishwasher fits into the niche you prepared, you can continue installation. The next stage of work is connecting the dishwasher to the water pipe and sewer pipe. There are two options for connecting a Siemens dishwasher to the sewer system, the first involves connecting the drain hose to the siphon, the second to the sewer pipe directly. The first option is used more often, so we will consider it.

First you need to install a special siphon with a side outlet under the sink. It is specifically designed to connect the drain of a washing machine or dishwasher.
We seal the threads on the siphon outlet with FUM tape. The fumka should be wound not along the thread, but against it, it’s more reliable.
We screw the drain hose to the siphon and move on to the next step.

Next, you need to connect the inlet hose to cold water. First you need to unscrew the sink faucet inlet hose from the pipe. Then you need to screw the tee valve onto the pipe, not forgetting to seal the connections. We screw the mixer inlet hose onto the tee on one side and the cleaning filter on the other. We screw the aqua-stop valve to the filter along with the dishwasher inlet hose. We screw the other end of the hose to the thread of the dishwasher fill valve and that’s it - the job is done.

Note! When installing a filter that purifies tap water, do not forget about it. In the future, clean it at least once every 6 months, and if there is a significant amount of sand and other dirt in the water, once every 2 months.

Connecting the water supply

The first thing we want to immediately emphasize is that, regardless of the type of PMM, connecting it to hot water from a domestic water supply is highly not recommended. This is due to the fact that fewer requirements are applied to the “purity” of hot water than to cold water, which will negatively affect the operation of the PMM.

In most cases, the reason why a dishwasher check valve fails is directly related to poor water quality. The result will appear instantly - cleanly washed dishes will have a rather unpleasant odor. To eliminate such a breakdown, repairs will be required, for example, in Astana or Balashikha.

Note that many models of imported PMMs (Bosh, AEG, Ajnev, Beko, Candy) are very critical to the composition of water, as well as its hardness, so it is recommended to install filters even for cold water. This will significantly extend the life of the equipment.

Now let's move directly to the connection. It is carried out according to the following algorithm of actions:

the whole process begins with shutting off the water entering the apartment. There is no need to turn off the entire riser in the house; as a rule, taps are installed on the supply to the apartment, and they need to be closed;
After the water is turned off, it is necessary to disconnect the henka (hose) from the mixer installed on the sink. We no longer need the old waterproofing from the hose, so we need to remove it;
screw the tee onto the pipe and connect it to the mixer. A ball-type valve is screwed into the middle outlet of the tee, and a hose from the PMM is screwed onto its output. When making all connections, each threaded joint must be wrapped with FUM waterproofing tape, and if required, a rubber gasket must be installed.

If you want to watch the whole process in more detail, then its video can always be found by visiting thematic sites.

Example of a completed connection

If the hose included in the kit is short, you can extend it or purchase a new one of the required length. The latter is preferable.

Final stage of work

Now all we have to do is connect the power cord to the outlet and put the dishwasher in place. Please note that you can only connect your dishwasher to a separate, moisture-resistant outlet. Do not connect the device through a tee, extension cord or adapter. It will be great if you bring out a copper wire with a cross-section of at least 2 mm for the socket, in good insulation, install a difavtomat and a voltage stabilizer.

Remember! Working with electrical communications requires skill and some knowledge; if you do not have this, do not experiment - it is life-threatening! Contact a specialist.

After connecting the power cord to the outlet, test run the Siemens dishwasher in strict accordance with the instructions, without loading dirty dishes into the appliance. After completing the test program, if the Siemens dishwasher does not generate errors, then you can begin to operate it.

Instructions on how to set the temperature in a two-chamber Samsung refrigerator

To summarize, we note that installing a Siemens dishwasher yourself is not much more difficult than installing any other dishwasher. The main thing is to remember and take into account the nuances described in this text, and everything will work out as it should!

Installing a Siemens dishwasher requires a competent approach. It’s good when you have extra money to hire a specialist who will correctly connect complex and expensive German equipment. But what if the installation falls entirely on your shoulders? It is important to follow clear rules for connecting the PMM to three communications - the electrical network, water supply and sewerage. We will tell you the details of this process and tell you about the intricacies of installing Siemens dishwashing equipment with your own hands.

How to install a Siemens dishwasher

The installer connecting the Siemens dishwasher acts in accordance with the manufacturer's instructions. He has a set of necessary tools at his disposal, and his experience allows him to do everything quickly and with a guarantee of quality. The list of works looks something like this:

checking or installing a new outlet;
placement of a dishwasher;
connecting it to the sewerage system, water supply system, and electrical network;
securing equipment with screws or self-tapping screws to the sides of furniture;
fastening the facade if necessary.

Once the installation of the Siemens dishwasher is complete, a test run is carried out and the customer evaluates the work. You can call a plumber at the numbers listed below or through the online form.

We have prepared good discounts for our clients:

5% when ordering services up to RUB 15,000.
8% when ordering work with a total cost of 15,000 to 20,000 rubles.
10% for those who order plumbing work from us for an amount over 20,000 rubles.
10% for all pensioners, disabled people, WWII or Labor Veterans.
5% when ordering services online through the website form.

We select components and parts

SONY DSC
If a standard connection is made, then the components and spare parts included with the device will be enough for you. But experts say that every second installation case is specific, so the problem of a shortage of components arises and some things have to be purchased. So, if the dishwasher inlet hose does not have an Aquastop valve, it will need to be purchased separately.

Important! If you decide to equip the filling system with Aquastop, purchase only the original valve, specially produced for Siemens brand dishwashers. In some cases, valves from PMM Bosch are suitable (these are products of the same concern), but they may not fit some models.

Several factors speak in favor of purchasing original components and parts:

Reliable connection and operation. With factory parts, the car will last longer, so the overpayment is completely justified.
Guarantee . If a breakdown occurs and the service center determines that this was due to incorrect connection and, in particular, due to the use of analogues rather than original parts, the company may refuse free warranty repairs. So, if the hose length is not enough for you, do not skimp and take an original element from Siemens, but of greater length.

There are some problems when selecting components and spare parts. The manufacturer refused to standardize parts when developing even similar models, so many hoses have a non-standard diameter or unusual fastening. This is the main drawback of equipment from Siemens; otherwise, these are high-quality and modern dishwashers.

Counter reset Brother HL-1110R/1112R, DCP-1510R/1512R, MFC-1810R/1815R with TN-1075 cartridge

To connect equipment to the water supply and drainage system, you will need the following kit:

Inlet hose (for drawing water from the water supply).
Drain hose (for draining waste liquid into the sewer).
Shut-off valve with several outlets - 2, 3 or 4.

Gaskets.
Filters.
Adapters.

This is a kit for standard connection of dishwashers, which means that other consumables may be needed during operation; this, by the way, can be specified in advance in the user manual for the equipment. What could it be?

Proper installation also requires a pressure reducing valve . If the pressure in your water pipes exceeds 1 MPa, in order to eliminate possible leaks and other problems, you need a valve that will stabilize the pressure.

Stabilizer . This item will be needed for a safe connection to the electrical network. The device is simply necessary if periodic power surges are observed in networks. A stabilizer is an excellent investment, because it will protect not only the PMM, but also other equipment in the house from voltage surges.

Additional hose + tap and filter for connecting the machine to a hot water pipe. All this will be needed if your dishwasher model is capable of drawing hot water from pipes, and the parts to implement this feature are often not included in the kit.

Water drainage

Once everything is prepared, you can begin connecting the machine to the sewer system. To do this, you need to install a siphon equipped with a fitting and connect a drain hose to the latter. This, at first glance, simple procedure for organizing a drain requires compliance with two important conditions.

The first condition is that you need to make an upper bend, as shown in the image below, this will prevent water from entering the sink bowl into the PMM.

Illustration of performing an upper bend

The second condition is that the elbow of the water seal on the drain should be as deep as possible with a short bend. This is done to ensure that air from the sewer system does not enter the device. If you do not install a water seal, the dishes may have an unpleasant characteristic odor after washing. The correct water seal is shown below.

An example of organizing a water seal

We do not recommend implementing the method of organizing a drain from a stationary PMM directly into a sink, since the load on the pump increases significantly. We will not even consider options for connecting directly to the sewer, since this is absolutely wrong.

Choosing an installation location: how much free space will be needed?

To integrate a machine into a ready-made furniture set, for example, into an IKEA kitchen, you will have to work hard - problems may arise when installing a built-in Siemens machine into furniture. Experts give their advice on this matter:

When preparing a site for a fully or partially built-in model, measure the equipment. Do not believe the values indicated in the instructions or in the characteristics in the product description in the online store. Measure EVERYTHING - any protrusion. Also, be sure to provide spare centimeters between the body and the walls of the niche - a couple of centimeters on the sides and 1 centimeter at the top.

Make sure in advance that you can secure the facade and metal sheet against steam , if it is included in the kit. If you remember this after connecting the machine, inconvenience will arise.

Prepare the floor for the car - almost all models of the German brand require installation on a stable surface, although their “brothers” from Bosch can easily stand on any floor. Despite good stabilization and the ability to work with surface inclinations of up to 7° or more, it is better to level the floor.

If you have a lot of floor-standing kitchen appliances and even a washing machine in the kitchen, solve the problem with the floor completely - this way you will extend the life of all appliances at the same time.

Do not move the machine more than 2 meters from the point where it taps into the water and sewer pipe. Too large a distance will increase the load on the pump and valve and reduce the operating time of these elements.

Connection to electrical wiring

This stage is the simplest, if you have everything prepared to turn it on, then just insert the plug into the outlet. No special connection diagram is required when installing a dishwashing machine. But certain conditions must be met.

The electrical wiring must be designed for the power of the PMM; it is advisable to power the machine via a separate line, which is connected to the RCD in the electrical panel. Sockets for connecting PMM must be waterproof (IP44) with grounding. Please note that according to the operating rules for such devices, it is prohibited to use them without connecting them to protective grounding.

Video on the topic:

Do not connect to utility pipes for grounding; this is guaranteed to damage the device and may endanger your life.

If you are not sure that all the conditions have been met, then it is better to consult professionals on this issue.

Water and drain connections

Having figured out how to install and where to place the case, proceed directly to installation. You can play around with the sewer system: there are 2 ways to connect to the drain - through a siphon and directly to the pipe. The first option is usually used, consider its sequence:

TOP 5 best DVRs with a rear view camera from different manufacturers

Install a siphon with a side outlet . If you already have a siphon installed for your washing machine with two outlets, use the second outlet for the PMM.

Ensure the tightness of the threads on the siphon outlet using FUM tape. Wind the “fumka” against the thread.
Screw the drain hose to the siphon.

Now you can install the inlet hose. Proceed like this:

Twist the sink faucet intake hose from the pipe.
Screw the tee valve onto the pipe, making sure to seal the connection.
Screw the mixer hose onto one end of the tee, onto the other end the Aquastop valve together with the PMM intake hose, and attach its other end to the valve thread on the equipment body. Ready!

Important! The filter element requires cleaning at least twice a year, so if you install a filter, do not forget about it. If the water is hard, with sand and other particles, inspect and clean it every couple of months.

Necessary tools, materials and consumables

To install a dishwashing machine yourself, you don’t need a specialized tool, all you need is:

an adjustable wrench, if you don’t have one, as a last resort you can use pliers;
Screwdriver Set;
insulating tape, it will be wrapped around metal threaded parts before tightening them with pliers. Accordingly, if you have an adjustable wrench, electrical tape will not be needed.

Materials you will need:

a siphon equipped with a fitting, for example, such as shown in the figure. If you also plan to connect a washing machine, then select a siphon model with two fittings;

Various models of siphons with fittings

To connect the water, you will need to cut into the pipe; for this purpose you will need a tee. If you don’t want problems, we don’t recommend purchasing silumin reinforcement; it can fall apart for no apparent reason. It is best to opt for brass, metal-plastic or bronze products;

Tee 3/4″

ball-type valve, the requirements for the materials from which it is made are the same as for the tee;

The tap to which the hose will be connected

In addition, you will need to buy a special waterproofing tape (FUM). You should not use insulating tape instead: firstly, it is thick and it will be problematic to tighten the thread, and secondly, the insulating tape will soon dry out, resulting in a leak.

Final stage

When the facade is in place, and the issues with drainage and water intake have been resolved, all that remains is to connect the power cord to the outlet. Please note that the outlet must be separate and preferably protected from moisture. Connection through a tee or using an adapter is excluded. Ideally, install a separate well-insulated copper wire with a cross-section of at least 2 mm for the socket and install a difavtomat with a stabilizer.

Attention! Working with electricity is impossible without the appropriate knowledge and experience. If you have never carried out such work, do not risk your health and contact an electrician.

Having completed all the work, close the PMM door and turn on the test mode, acting as prescribed in the instructions - with an empty hopper without utensils. If at the end of the cycle the equipment does not report an error, you can use the dishwasher you installed yourself!

If you have any questions, watch the video:

BadInteresting1Super —>

Siemens technology is a benchmark for innovative technical implementations and stylish design. A convenient Siemens dishwasher makes people's lives much easier.

Brand Features

The company has been in demand for a long time; it was the first to introduce a built-in dishwasher to the world, and such a compact model as the Lady 45 brought great popularity to the brand.

Siemens dishwashing units are considered premium equipment. This status is assigned to the brand due to the following features:

Reliable technology. All PMMs are manufactured in Germany, and German equipment is considered to be of high quality.
Manufacturability. Siemens machines are quite efficient and safe because they have an inverter engine installed.
Functionality. The company constantly introduces innovations, producing multifunctional units. For example, when using a Siemens dishwasher, a person can independently choose the temperature, adjust the speed, and control the drying.
Technical specifications. The energy consumption of these units is quite low, and they operate quietly, the noise does not exceed 45 dB.

Siemens has a wide range of products, so each consumer can choose equipment that best meets their needs.

Advantages and disadvantages

Among the advantages of the brand:

Competent development of water distribution in the working cavity.
High-quality washing is carried out due to 3 upper rocker arms.
Automatic installation of programs depending on the level of soiling of cookware sets.
Protection of equipment from overload and temperature changes.
Preventing scale formation, adjusting water hardness.
Thanks to the flexible basket adjustment system, convenient loading of dishes, even the most non-standard designs, is ensured.

Among the brand's shortcomings, the following are most often noted:

Limited capacity of cookware sets.
Inconvenient location of the salt container in the workspace.
The end sound of washing dishes is not loud enough.
Lack of child protection.
High pricing policy of the brand.

Although these machines have disadvantages, users leave mostly positive reviews.

Comparison with competitive firms

Siemens PMMs are popular household appliances. Compared to Bosch, it can be noted that water and energy consumption are more economical. In addition, Siemens equipment can be connected to hot water.

Most modern brands offer more convenient control systems and electronic displays.

AEG units (unlike Siemens dishwashers) have child safety features and provide better safety.

Best models

Each buyer chooses the most suitable model in terms of technical parameters and price. There is a list of the most popular Siemens models.

iQ100 SR64E073

A model of a small narrow dishwasher that can clean up to 10 sets of dishes at a time. The equipment has electronic control and many cleaning programs (intensive, half, delicate, etc.). A BIO program has been developed, i.e. washing using special bio-additives.

iQ100 SR215W01NR

This dishwasher model has a rotary switch as a control and is designed for 10 sets of dirty dishes. There are 5 programs for cleaning, including the popular “fast” and automatic washes.

iQ700 SN678X50TR

One of the most expensive models from Siemens, which is characterized by quiet operation, has a hygienic cleaning program and an antibacterial protection function for dishes and glasses. This technique has a shortened washing cycle and convenient trays for loading dishes into the workspace.

SN 278I36TE

Dishwashing equipment for cleaning dishes from the Siemens brand with electronic control and a convenient Aqua-Stop function. The machine has 8 main programs for cleaning no more than 13 sets of dishes, glasses, and cutlery. The machine is equipped with a SpeedMatic hydraulic system, which provides alternating water supply.

What brand of equipment do you use at home?

Bosch 16%, 297 votes297 votes16%297 votes - 16% of all votes
Samsung 14%, 270 votes270 votes14%270 votes - 14% of all votes
LG 13%, 244 votes244 votes13%244 votes - 13% of all votes
Atlant 7%, 125 votes125 votes7%125 votes - 7% of all votes
Indesit 6%, 116 votes116 votes6%116 votes - 6% of all votes
Electrolux 6%, 108 votes108 votes6%108 votes - 6% of all votes
Philips 3%, 61 votes61 votes3%61 votes - 3% of all votes
Beko 3%, 54 votes54 votes3%54 votes - 3% of all votes
Ariston 3%, 51 votes51 votes3%51 votes - 3% of all votes
Xiaomi 3%, 49 votes49 votes3%49 votes - 3% of all votes
Haier 3%, 49 votes49 votes3%49 votes - 3% of all votes
Redmond 2%, 46 votes46 votes2%46 votes - 2% of all votes
Liebherr 2%, 35 votes35 votes2%35 votes - 2% of all votes
Candy 2%, 31 votes31 votes2%31 votes - 2% of all votes
Siemens 2%, 30 votes30 votes2%30 votes - 2% of all votes
Hansa 2%, 30 votes30 votes2%30 votes - 2% of all votes
Whirlpool 2%, 29 votes29 votes2%29 votes - 2% of all votes
Gorenje 1%, 28 votes28 votes1%28 votes - 1% of all votes
Midea 1%, 27 votes27 votes1%27 votes - 1% of all votes
Zanussi 1%, 26 votes26 votes1%26 votes - 1% of all votes
Karcher 1%, 25 votes25 votes1%25 votes - 1% of all votes
AEG 1%, 24 votes24 votes1%24 votes - 1% of all votes
Vitek 1%, 21 votes21 votes1%21 votes - 1% of all votes
Miele 1%, 16 votes16 votes1%16 votes - 1% of all votes
Dyson 1%, 13 votes13 votes1%13 votes - 1% of all votes
Thomas 1%, 13 votes13 votes1%13 votes - 1% of all votes
iRobot 1%, 12 votes12 votes1%12 votes - 1% of all votes
BBK 1%, 12 votes12 votes1%12 votes - 1% of all votes
Nord 1%, 11 votes11 votes1%11 votes - 1% of all votes
DeLonghi 1%, 10 votes10 votes1%10 votes - 1% of all votes
Kuppersberg 1%, 10 votes10 votes1%10 votes - 1% of all votes
Zelmer 1%, 10 votes10 votes1%10 votes - 1% of all votes
Scarlett 0%, 8 votes8 votes8 votes — 0% of all votes
Smeg 0%, 4 votes4 votes4 votes - 0% of all votes
iLife 0%, 1 vote1 vote1 vote - 0% of all votes

Total votes: 189622.01.2020× You or from your IP have already voted.

iQ500 SN656X00MR

The machine belongs to the highest class technology; thanks to technical developments, the internal space of the chamber is used more efficiently. There are cleaning programs for glasses and porcelain with a delicate protection function. For ease of use and maintenance, a self-cleaning option is built-in. There is an AquaStop function and a ServoSchloss lock.

iQ100 SR64E072

Built-in machine from Siemens with a set of standard options for high-quality and quick cleaning of dishes. The model is equipped with a ServoSchloss lock, which allows you to automatically close the door if the opening angle is less than 10°. The color of the machine is black, there is an alert sound and an additional Info Light indicator.

iQ100 SR216W01MR

Compact model with electronic control. Designed for 10 sets, 6 standard cleaning programs have been developed. Freestanding dishwasher, which has the option of an economical or express wash; a delicate washing option has also been developed for glasses and crystal. For heavily soiled dishes, a special mode is provided, as well as VarioSpeed and IntensiveZone functions.

SR64M001

Siemens offers a new built-in machine that allows you to clean up to 9 sets of dishes at the same time.

The compact model provides 4 main programs, including quick wash, as well as “eco” or “auto”. The silver design will look great in a modern kitchen and will fit perfectly into any interior. There is a signal about the end of the washing cycle, a double rocker with DuoPower rotation.

Instructions

In order for the equipment to last as long as possible without wear and tear, it must be used according to the instructions.

Although each Siemens dishwasher has its own instructions for use, there are standard rules for all, such as:

It is recommended to use PMM only at home.
Do not overload the equipment with a large number of dishes.
Each type of dishware is placed in special compartments and baskets.
When working, you must use the built-in functions and protection options.
In case of scale or hard water, it is necessary to use specialized salt.
To eliminate streaks and stains, it is necessary to use special rinses.
Timely preventive maintenance and maintenance in specialized centers will help prevent breakdowns and extend the service life of equipment.
If an electronics failure or breakdown occurs, you should not repair the equipment yourself; it is better to seek qualified help.

How to connect and install

The location for installation and connection of the Siemens dishwasher should be chosen close to the outlet and sewer drain.

It is important that the work is carried out by a specialist, since a lack of experience can lead to an unsafe situation and equipment breakdown.

First, the connection to the drain and water supply is made, and then the connection to the electrical network.

This type of equipment does not tolerate the effects of elevated temperatures well, so contact with heating devices should be limited.

How to turn it on

To properly turn on the dishwasher, you must follow several recommendations:

Press the main switch or turn the lever.
Select a washing program after loading dishes and special products.
Close the door and check for leaks.
After the end of the cycle, a beep will sound and the indicator will light up, you can open the door.
Turn the switch to the “off” position.

How to use

You can start using dishwashers after thoroughly studying the operating instructions and user manual.

What to do before using:

Load regeneration salt into a special tray to prevent scale formation and damage to mechanisms. To do this, you need to unscrew the hatch cover, add 1 kg of salt and be sure to add rinse aid to remove streaks and stains on the dishes.
It is necessary to load the cleaning agent according to the instructions (depending on the amount of dirty dishes in the workspace).
After selecting the program, check all connections.

Troubleshooting

The Siemens company offers reliable and high-quality dishwashers for sale. The risk of breakdowns with this equipment is minimal, but sometimes problems can occur:

There is no water in the work area. It is necessary to check the supply tube and remove the blockage.
The indicators do not work, the machine does not turn on. This indicates a lack or voltage drop.
Water has been filled, but the washing process has not started. The motor or pump has become unusable.

To prevent problems, it is necessary to protect the machine from voltage surges using special devices.

Having a Siemens dishwasher in your home is a definite plus, but you need to choose a model taking into account all the technical characteristics and financial capabilities.

Features of Siemens dishwashers

Siemens produces these household appliances in a wide range. None of our competitors have such a variety of small-sized dishwashers that cope with their main task just as successfully.

In the Siemens catalog you can even find dishwashers of reduced height, installed under the kitchen sink. At the same time, installing and connecting a Siemens dishwasher is a responsible task. It is better to trust it to experienced craftsmen from San Remo, who will do everything carefully and correctly.

You can find out the exact price for installing a Siemens dishwasher by calling a specialist to your home for a preliminary consultation. He will estimate the scope of work and announce the total cost, and general prices can be found below.