Washing Machine Atlant How to Clean the Water Supply Filter • Possible problems

Regular cleaning of your washing machine not only helps keep it looking its best, but also helps it run efficiently. The fact is that washing machines tend to accumulate:

• Fungus and mold in the sealing gum and, accordingly, the appearance of unpleasant odors;
• Scale on the heating element;
• Residues of powder, rinse aid and other additives inside the machine;
• Dirt and small things in the drain pump filter;
• Rust and sand in the inlet hose filter.

Therefore, over time, you may notice that your clothes (especially light ones) after washing are no longer sparkling clean as they were before. And external dirt that quickly covers the door, countertop and protruding parts of the machine spoils the appearance of the room.

How often do you need to clean your washing machine from scale and dirt? Optimally – once every 2-3 months. If you have a pet at home or you often wash woolen items in a machine, then major cleaning needs to be done more often.

From this material you will learn how to properly clean a washing machine as a whole, namely:

• How to clean the drum of a washing machine, and most importantly, the heating element;
• How to clean the pump in a washing machine (drain filter);
• How to clean the tray and powder receiving compartment;
• How to clean the inlet hose filter;
• How to remove external dirt on the car body and door.

And at the end of the article you will find some tips on prevention and care for your assistant.

The most incredible way to get my hair back!

This is just a DISASTER ! And after all, my hair did not start falling out in one day, but systematically - day after day I watched how the hair left my head: while combing, washing, even while sleeping. (read more…)

How to clean the filter in the Atlant washing machine, Candy

Afterwards, you can disconnect the drain hose from the machine and feel the corrugation for blockages. If “clogging” is present, clean the hose with a special cable and reconnect it.

Expert opinion

Ekaterina Korneva, expert in the field of care, cleanliness and beauty

I will help you understand all the intricacies.

A program with the maximum washing temperature is set, a special descaling powder is poured into the device, and the unit starts up without laundry. The drain filter in a washing machine is often installed at the bottom of the body behind a plastic protective cover. How to clean a washing machine with home remedies in 5 steps (photo) If you have any questions, please contact me, I will be happy to answer!

How to clean an Indesit washing machine?

You can clean the Indesit automatic washing machine, and specifically this part, in the following way:

1. Turn off the water.
2. Unscrew the inlet hose.
3. Use pliers to pull out the mesh.
4. Using a regular toothbrush, remove all dirt from the part.
5. Now rinse the mesh under strong water pressure.

Interesting materials:

How does asthma develop in children? How does a baby's vision develop? How to develop fine motor skills in a child? How to develop will in a child? How do you get scammed when renting an apartment? How to dilute modeling clay? How to dilute baking soda with salt to rinse teeth? How to light a fire in the forest after rain? How to light a fire in wet weather? How to resolve conflicts in a team?

When is cleaning recommended?

In the case when the requirements for periodic cleaning of the filter were ignored, or the owner of the Atlant washing machine was not familiar with such subtleties, then certain signals will become a kind of call for this:

• there will be an unusual noise during the washing process, reminiscent of chirping,
• the drainage of liquid will slow down,
• the programmed process will be interrupted without the possibility of its resumption,
• things will remain wet, the spinning process will be ineffective,
• an alarm sign will appear on the dashboard screen of the Atlant washing machine - the indicator lamp will indicate that it is necessary to check the filter,
• Other changes in the functionality of the unit may occur that differ from normal operation.

You can do the cleaning yourself, but if you have never done such an operation, it is recommended to use the services of an experienced professional.

Expert advice

1. The optimal cleaning frequency is once every 2-4 months.
2. If you use the SMA daily or wash very dirty laundry, check the filter monthly.
3. In winter, check the part once every 2 months - it becomes clogged with lint and wool.
4. The valve is cleaned after each wash of pillows, blankets and jackets with feather and down fillings.
5. It is better to wash heavily soiled fabrics in mesh bags.
6. Shake out your clothes before storing them or brush off any debris, and take small items out of your pockets.
7. Turn wardrobe items decorated with rhinestones, beads, beads, sequins, buttons, rivets inside out.
8. Clean the filter immediately if an error code appears on the display, clothes are not washed well, and there is water left in the drum or a musty smell.

Prevention of the drain filter of the Atlant washing machine

This element can be blocked by random objects in the machine drum. For example, there was a small coin in your shirt pocket, which would be enough to create difficulties when draining. For this reason, before washing items, it is necessary to carefully check the contents of their pockets.

To clean the drain filter of the Atlant washing machine, you will have to perform certain actions:

• use a screwdriver or tweezers to lift the cover located on the front of the machine body at the bottom,
• drain the remaining liquid, after placing a container under the filter hole,
• Now you should turn the handle counterclockwise, remove the filter,
• The part is cleaned with a brush, washed,
• a plug is installed in the sleeve, the drain filter of the Atlant washing machine returns to its place, the lid closes again.

The drain filter mesh on the Atlant washing machine is cleaned every six months. As an additional measure, such work should be performed after the next wash of woolen items.

Cleaning the water intake pump filter

Any preventative work on the Atlant washing machine involves certain actions. To begin with, the unit is disconnected from the power supply, then the flow of water into the device is cut off. These are the basic operating rules that protect against electric shock and flooding.

The pump filters of the Atlant washing machine are located in the water intake hose and in the pipe of the electronic valve. These designs are designed to retain mechanical impurities that can penetrate into the machine from the water supply network - sand, metal particles. Debris in the liquid, settling on the mesh, interferes with normal water intake.

The algorithm of actions is as follows:

• the nuts are turned against the direction of movement of the clock hand, the filling hose is disconnected from the liquid intake valve and the pipe located on the valve,
• pump filters are removed using tweezers or pliers,
• cleaning is best done with a brush, holding the element under the tap,
• all elements are installed in their places.

Please note that the filling system screens must be cleaned annually.

Where is the problem?

It can be difficult for a simple consumer to determine the location of the filter. Following the usual logic, the owner tries to find the required element in the immediate vicinity of the water supply system, or with good reason believes that the drain point requires cleaning.

Let us immediately note that each of these decisions turns out to be correct. The design features of the Atlant washing machine involve cleaning the water during its intake and at the end of the washing process, and our model has a pair of filters - inlet and drain.

Some washing machines are equipped with devices for additional liquid purification, but they are installed not in the factory, but in service centers according to individual user orders.

How to check the performance of a household appliance after?

After the filter is cleaned and installed in place, it is necessary to check the performance of the system as a whole . This is done so that after the first start-up, water does not leak out onto the floor, which can happen if the filter is not tightly screwed on.

To check, you need to select the “rinse” program. While performing this mode, you need to make sure that the machine does not leak. If everything is dry, then the hatch can be closed and you can continue to use the device as usual.

Problems that arise when dismantling the filter

How to remove the filter element from the washing machine for cleaning if it cannot be unscrewed? This happens when there is severe blockage or scale formation. Your actions should be as follows:

• The washing machine is laid on its side, the drain pump is dismantled to try to remove the filter part from the inside. It happens that these actions also remain ineffective,
• in this case, to perform cleaning, it remains to remove the drain system completely to make it easier to deal with the problematic issue.

Removing stubborn stains

If the last filter cleaning was carried out a long time ago, then it is not enough to just rinse the nozzles under water. To remove rust or a thick layer of scale, you will have to use “heavy artillery.” The main thing is not to overdo it and choose the right products so as not to spoil the plastic and rubber seals.

For minor plaque, toothpaste and laundry soap will help cope with the problem. It is necessary to apply the product to the spiral and clean thoroughly with a brush. For advanced cases, there is a more effective method:

• dilute 20 g of soda and 50 g of citric acid in a liter of warm water;
• lower the filter into the solution for 15-30 minutes;
• take it out, wipe it with a cloth and rinse in cold water.

Do not wash the drainage filter in hot water - at high temperatures the material is deformed!

Instead of home remedies, you can use special store-bought formulations. Some recommend running a high-temperature “idle” cleaning cycle before unscrewing the garbage filter to simplify the task of manually washing the spiral. In any case, it is necessary to monitor the dosage.

Prices for services

The Atlant washing machine has its own list of typical malfunctions that arise due to improper care, operating errors, and equipment wear. It is these reasons that more often than others lead to sad consequences, forcing the owner to stop washing and search for the source of the breakdown.

Doesn't turn on

In a standard situation, the washing machine starts, the drum rotates inside the tank, everything proceeds as normal. Any failure in a well-functioning circuit is a reason to pay attention to what exactly may be wrong.

Trouble-shooting

1. The top panel needs to be removed.
2. It may be necessary to remove the clamp used to secure the door.
3. In some cases, it may be necessary to remove the bin that is intended for detergents.
4. It is necessary to remove the control panel by unscrewing the screws that hold it in place.
5. The fastening screws securing the hatch locking device are unscrewed.

If it is impossible to open it from the front side, you will have to get it from the inside. To do this, the washing machine must be laid on its side. For example, Candy has a removable plastic bottom panel. It is not secured in any way. When you remove it, the pump will be in front of your eyes.

Cochlea extraction methods and pumps

Before cleaning the filter through the snail, you need to find the pump. Its location in various modern washing machines can vary greatly depending on the type of load and manufacturer. And knowing where the pump is located, you can save time on removing it. It is best to refer to the factory instructions and find the center of the drain system on the page describing the internal structure . If the manual is not at hand, we navigate as described below. So, owners of frontal automatic machines will have to choose from three possible options.

1. Through the bottom. Many washing machines have no bottom or can be easily removed. In such cases, the easiest way to get to the cochlea is to tilt the unit body back 45-60 degrees and find the pump immediately behind the filter.

Important! This method is not suitable for Bosch models due to the presence of a metal strip at the bottom that secures the dampers, and for those machines at the bottom of which there is an “Aquastop” sensor, designed to protect against leaks.

1. Behind. If the drain pump is located closer to the back wall, then it is better to disassemble the washing machine from this direction. For example, this is done with machines from Ardo, Indesit, BEKO and Haier. To do this, just move the machine away from the wall, unscrew the four screws and remove the panel.
2. Front. Owners of frontal Bosch and Siemens often have to get to the pump through the front panel. This method is the most labor-intensive and will take a lot of time. First, the top of the unit is dismantled, for which the two rear retaining bolts are twisted. Then you have to loosen and remove the outer clamp on the cuff and tuck the sealing rubber inside the drum. We also disconnect the dispenser, control panel and UBL wiring. Next, close the door tightly, loosen the four screws and remove the front wall. Finding the pump will not be difficult - it will be right behind the filter.