The main malfunctions of Beko washing machines

Typical malfunctions of Beko washing machines

By entrusting the inspection of your car to an experienced technician, you can rest assured that he will quickly and professionally find what the problem is. But due to the high prices for services, many home craftsmen are trying to save money and repair the Beko washing machine themselves.

Almost any SMA model can be repaired at home: ELB 57001 M, RKB 58801 MA, LNU 68801, etc.

This approach is quite justified - often repairs are exorbitantly expensive, and sometimes the price is such that you can buy a new machine. At the same time, even the most “killed” car can last for several more years after repair.

Don't want to throw away your Veko machine and buy a new one? Try to figure out the problem yourself and fix everything yourself.

The design of the Beko washing machine also determines the nature of its breakdowns. Let's look at typical malfunctions of washing machines of this brand:

The water does not heat up to the set temperatures; washing is done in cold water on any program. Or vice versa - the water overheats.
Water slowly fills into the tank or does not fill at all.
The Beko washing machine does not start because the hatch does not close tightly enough.
There is water standing in the tank at the end of the wash (this may be accompanied by a strong hum).
The rotation of the drum occurs with grinding, roaring, clanging and other uncharacteristic sounds.
Not a single washing mode starts - all the lights on the machine blink. Or the program works, the indicator lights up, but the machine does not wash.
It is not possible to start the machine with the power button (with the power cord plugged in).
Models with an electronic display display error codes H1, H2, H3, H4, H5, H6 and H7. The machine doesn't work.

Important! There may be other signs of failure. We looked at the most common ones among Beko SM users in Russia.

Features of typical breakdowns of Beko washing machines

As mentioned earlier, all malfunctions are accompanied by certain symptoms - from minor malfunctions to complete failure. The problem of the home handyman always lies in one thing - how to connect the existing signs of breakdown with its causes. Here you just need the knowledge and advice of specialists of a narrow profile.

Next, we will briefly summarize information about the main breakdowns.

Problematic drainage of waste water in Beko machines

If you know how to use a Beko washing machine, then you know that the waste water after washing is not clear and clean - this is the specificity of washing. To prevent dirt, threads, hair, etc. from clogging the pump, there is a special drain filter on the way to it, which mainly suffers from blockages.

Your task is to find this filter, which is usually located at the bottom of the washing machine, under a small hatch or behind a panel. How to proceed next:

Before removing the filter, do not forget to place a basin or a rag under the machine, because residual waste water will definitely flow out of the hole.

In a number of Beko models, along with the filter, an emergency drain hose is also included - with its help it is much more convenient to drain water into any container.

To remove the filter, simply twist it to the right.
Next, clean the filter by hand and rinse under the tap.
Armed with a screwdriver, you can also clean the pipe - it usually also becomes clogged with debris from waste water.
Once you have the tools at hand, do not rush to put them away - for preventive maintenance, also clean the filter that is located on the water supply (it is located at the place where the hose is attached to the rear panel). Sand and rust from the water supply slowly collect in this filter and eventually interfere with the normal flow of water into the drum.
After cleaning the inlet filter, do not rush to put it back in place - also check the drain pump. Often, Beko washing machines, during self-diagnosis, detect a breakdown of the pump and signal this using fault code H5. But in case of some breakdowns, the controller may not see minor violations - such as a loose impeller (can be identified by hearing a hum).
To check the pump, start the drain mode and look into the hole in the filter plug to see how the impeller behaves. If it rotates, then everything is in order, but if not, then the pump needs to be cleaned or even replaced.

Problem with water heating in Beko machine

To fix this problem, you will also need to at least partially disassemble the Beko washing machine, but more on that below.

First, let's say that in the SM one of the most vulnerable components is the thermoelectric heater, simply the heating element. The mineral salts present in the water crystallize under the influence of hot water and settle on the heater in the form of the familiar scale - like in a kettle. The coating does not allow heat to pass through, so the heating element does not transfer it to the water and burns out.

If there is no scale, you have soft water, or you use special products, this does not mean that the heater could not burn out. The heating element has its own production resource, and maybe its time has come.

If the heating element fails, you will know about it by errors H2 and H3. To be absolutely sure what happened to it, first get to the heater. In some Beko models it is located at the rear, in others it is at the front.

So, how to disassemble a Beko washing machine, find the heating element, check and replace it, read on:

If the heating element is located at the front, then to remove the front panel, you need to remove the hatch cuff. To remove it, act carefully - if something goes wrong, then your activity is fraught with damage to the cuff and leaks.
You will not see the entire heating element - only its shank with two contacts and wires going to them.
Disconnect all wires.
Take a tester and measure the resistance. Typically, normal readings will be 25-30 ohms. If the indicators are different (for example, infinity), then the breakdown is obvious.
Remove the heating element by unscrewing the nut from the bolt that holds it under the drum.
Clean the installation site from debris and deposits.
Install the new heating element in the reverse order, reconnecting all wiring.

This video shows in strict sequence how to remove, check and replace the heating element:

If the heating element turns out to be defective, then you need to check the temperature sensor (thermistor) . You will find it under the top cover. How to remove and check the sensor:

Remove the top cover by unscrewing the screws.
The sensor is dismantled by removing the detergent cuvette and the control panel - all of this prevents access to the element. Having reached the sensor, free it from the wires.
The resistance measured by the tester should be 4.7 kOhm in room conditions.
Heat the sensor in a glass of warm water - after this the readings should drop. If this does not happen, the sensor needs to be changed.
Installing a new sensor is the same as dismantling it, just do it in reverse order.

Repair and operation of Beko washing machines

_____________________________________________________________________________________

Models MVB WKN WMN WMB WKL
Models WKB WN WKE WME WM

The Beko WB 6108 washing machine (4.5 kg load) does not take up the air conditioner. Tell me, please, what could be the reason? Most likely the water supply valve has failed. It needs to be diagnosed, and if the resistance of the solenoids is not 2-4 kOhm, then it needs to be replaced with a new one. Can you tell me what's wrong with my washing machine and what repairs are needed? Model WB 6106 XD, its belt comes off during washing and during the spin cycle the drum hits the walls very hard. Should I change the belt or just need to tighten something? If the belt comes off during washing, then you definitely need to change it! The fact is that the belt clings very tightly to the motor and drum, and if it falls off, then there is no longer the required tension. This is precisely why play (knocking) of the drum against the tank of the unit could appear. Please tell me, I have SMA elb 67001 y. A breakdown has occurred: the machine turns on and draws water to the edge of the drum or, to be clearer, to the beginning of the door. And that's where her work stops. The drum doesn't start and you can't hear the engine running. After turning off the washing machine, the door opens in emergency mode. When restarting and changing the program, light clicks of the control are heard, but the drum does not rotate. If, after adding water, the unit does not continue the washing program, then the problem may be a breakdown of the heating element (water heater). After adding water, the machine should start heating, and if the heating element is faulty, then nothing happens. You can drain the water from it and run the spin program. If it works, then you need to change the heating element. Automatic washing machine Beko elb 67031 ptya. Malfunction - the drum operates jerkily. The problem is either the belt or the electric motor. Machine WMD 56120. When you set the drain mode and press the start button, the lock is activated, and the pump and drive begin to work almost simultaneously, after 3 seconds. processing stops, although the start button is lit. Inspection of the control unit (triac test) did not give the desired result, the capacitances are normal, and so are the contacts. I checked it in spin mode, same problem. In other modes, water is poured, washed, drained with the same fault. Can the control unit be replaced? I disassembled and cleaned the pump, checked it by applying voltage, everything is fine! I cleaned the block, rang the bell, everything is fine! There is no power supplied to either the pump or the motor. Inspect the pressure switch, if it is frequency, then check only by replacing it. Beko wmd 55100. 2 minutes after the start of washing it stops and does not allow you to reset the program and drain the water. Check heating, drain water. Washing machine Beko WKD 24580. Fills with water, reaches the set temperature, even spins. But when it reaches the first flush, it stops the whole process in limbo and a quiet hum is heard from inside. It doesn't drain. As soon as I add salt manually, the washing process begins again (but programmed in a new way). Also, the mini-wash stopped working for 30 minutes (which is what I used most often). I checked for clogging in the hose from the sink to the entry into the unit - there is no clogging. I blew out the hose itself - the air comes out through the open drain hole normally. What are your guesses? There may be several reasons. Faulty switch, wiring problem, electronic module. SMA WKD 65100 2010 During the spin cycle the drum stopped turning. There is sound, but the drum is still standing. Can it be repaired? The belt may have fallen off (broken). Possibly an engine defect. SMA WB 6108 SE. In operation for 9 years. When washing, it collects water, but the drum does not spin. But during the spin cycle the drum rotates. There may be a defect in the control module. The Beko wb 6110 xe washing machine is in operation. How can you select the washing temperature on it if there are no numbers with degrees on the temperature regulator? Please read the instruction manual carefully. You select a washing program, and it sets the temperature at which the process will take place. SMA elb 57001 does not drain or squeeze. Tell me the reasons. Until drainage occurs, spinning cannot begin. The drain filter is probably clogged or the drain pump has failed. Is there a filter in the Beko elb 67001 machine? You turn on the spin, and it doesn’t spin; it seems like the drum isn’t spinning. What to do? First, we recommend checking whether the water is draining. It is most likely that the drain pump (pump) has failed, which does not drain the water after washing, and that is why the machine does not spin (the laundry spins in the water and therefore does not spin). To check the operation of the drum, turn on the rinse mode. If the unit rinses, then the motor is working. Why does the Beko WMD 25080 washing machine knock out the machine at a speed of 1000-600? It only works at 400, although it used to work at 800, then at 600. They called an electrician and said that was the reason. Most likely, it is not the machine gun that knocks it out, but the RCD. The reason for this behavior is current leakage to the housing in the unit’s motor. The pump may also be to blame for the same reason. It breaks through during the spin cycle at high speeds, because the voltage load on the motor at this moment is higher than during washing. In general, if the RCD had not been installed, the washing machine would have received an electric shock during the spin cycle at high speeds. There was a problem with the washing machine. machine WKD 24580 T. The essence of the problem is that the spin light is constantly on, it is stuck on it. As soon as we close the door, the lock is locked, the spin light goes out, and that’s it, the stopper. Only when we turn off the power, a minute passes, the door unlocks and again hangs on the spin cycle. The program controller no longer responds to anything. The problem arose due to the fact that after washing they additionally turned on the water drain mode, but forgot to remove the speed control, it remained in the 400 revolutions position. The pump worked, drained all the remaining water, and unlocked the door. After this, the spin light came on. I heard that you can remove a board or processor error by holding down certain keys and holding them down for a while. Tell me how to do this or some other way? To begin with, we recommend that you disconnect the washing machine from the power supply for 20-30 minutes to reboot the control module. If that doesn't help, try resetting the program. In order to reset the program on this model, you must press and hold the “Start/Pause” button for 15-20 seconds. If this does not help, then the problem may be with the control module. Washing machine Veko WKD 25080 T worked for 3 years. Problems with operation began: it starts to wash, then immediately rinses, freezes, confuses the program, etc. what can be done? Is there an option for simple “at-home” repairs on your own? The control board may be faulty; the engine tachogenerator should be checked. Altus machine 3.5 kg. Drain problem. I checked the hoses and washed them. The pump is spinning. All is clear. I look at the ball. When draining the water, it probably goes down and blocks the hole in the hose. How to get rid of this? Maybe there should be some kind of ball movement limiter? Maybe it (the limiter) broke off? And this is how the ball blocks the outlet of water? Tell me, please, what to do about this? The ball that prevents self-draining should be in the drain hose and rise to the top when the drain pump starts operating. Beko 13500 machine with a loading capacity of 3.5 kg. Doesn't drain water. The pump is running and spinning. While disassembling it, I came to the ball that locks the drain from the drum compartment. Through a rubber pipe to the filter (by the way, for some reason the design does not provide a filter). I squeezed the ball and the water began to drain. He let go and the ball closed the exit. The role of the ball is not clear. When water comes in, it should float up, opening the water drain, but it constantly closes the exit. Should I throw this ball away? There is a problem with service. Please advise how to adjust it. The ball that you discovered works on the principle of a check valve, and its main function is to prevent large objects from entering the drain system, and water quietly passes through the gap between the ball and the pipe, because it does not fit tightly to the pipe. It's only needed for this. In fact, it cannot affect the lack of drainage. It is necessary to check the pump with a tester. The resistance of the working drain pump is from 140 to 200 Ohms. While washing the SMA elb 67031 ptya (in use for 5 years) it suddenly stopped and no longer washes. The drum makes a revolution or half a revolution approximately every 3 minutes and stops, the program on the display immediately turns off. Drain and supply works. The program also seems to work as it should. When cranking manually, the drum turns with little difficulty, it feels like there is strong friction somewhere. Also, when twisting, a noise is heard, as if something is rubbing somewhere, or the bearings are making noise. Help me find the problem. Invite a specialist. The bearings may be faulty. Eyelid elb 57021 ptms. A short circuit occurred during washing and the machine was knocked out. When the unit is turned on, the short circuit occurs again. Help, what could cause a short circuit? Short circuit in the MCA. For example, the heating element “breaks through” onto the housing. The Veko WB 6108 XD washing machine began to make strong grinding sounds during additional water suction after draining its main part. Tell me, please, what could be the problem? The pump may be faulty or the drain path may be partially clogged. When spinning clothes, the tub bearing makes a lot of noise. Washing machine WB 6110 SE. During disassembly I got to the bearing. I removed the separator from the bearing. There are traces of rust on the inner surface of the bearing races. I tried to wash the bearing without removing the drum. Washing was done with WD-40. After that I tried to introduce a new lubricant like Litol. After that, I returned the bearing separator to its place. When starting up, the SMA is quiet in all modes, except for the spin mode. Please advise what to do? In this case, it is necessary to replace the bearings and oil seal. SMA WKD 54500. There was a problem with rinsing. The washing phase goes without problems. When switching to the rinse cycle, the machine “freezes”: it draws water and does not turn the drum. The collection of water occurs in 3 stages: the first time the main amount is collected, after 30 seconds approximately 1/5 of the total amount of water is collected, after another 30 seconds the last “suction” of water occurs and the “start” and “wash” lights begin to flash. When you press the “start” button, water is drawn in again and rinsing begins. After the 1st rinse and draining the water, everything is repeated - adding water in 3 doses, flashing lights. Pressing the “start” button starts the second rinsing stage. Spinning goes without problems. In short programs this happens before each rinse, in long programs - only before the first. The drain pump filter is clean. Tell me where to start checking? Recently the washing machine was reconnected to another riser, if that helps. The problem seems to be the water pressure - too low. Change the gaskets at the connection point, it should work. Eyelid WKD 25125 T. The additional rinse button is constantly lit. How to remove it? And it constantly erases and does not turn off. You have to disconnect from the network and scoop out the water. Even on a mini wash it can work for 1.5-2 hours until you unplug it. Perhaps the electronic module is for repair or replacement. Washing machine Beko WMD 65105 BL. Tell me, please, I decided to change the bearings, took out the tank, and it was plastic without any fasteners, four pieces of guides and that’s it. Looks like he's on the hot seat. What should I do? To replace the bearings, the tank must be disassembled. Washing machine Veko WMD 55100. SMA does not block the door and therefore does not start the wash. Tell me, what could have broken? Problem with the UBL circuit (hatch blocking device). The problem is in the operation of the SMA WKD 24500. At the moment of startup, the valve starts water, then the engine accelerates to maximum speed and stops. Then the washing machine stops for 2-3 minutes, and the cycle repeats: starting the water and spinning the engine. The same thing happens in rinse mode. Is there no relay in the triac circuit that turns on or off the voltage supply to the triac? The engine does not rotate at minimum speed when washing, but spins up at maximum for about 10 seconds. Then the unit for 5 minutes. freezes, while the tank is filled with water. The triac is usually controlled from the processor via ULN; the processor gives a command to rotate the motor, but since it does not see its rotation, it turns it off. You need to look at the tachometer chain. Washing machine Beko WKD 23580 T. Possible cause of failure: banal overload. I got away with it many times, but this time it was a breakdown. The water does not drain, does not respond to the on/pause button. When you turn it on, the key button lights up for a few seconds, but then the automation clicks inside and the light goes to the drain button, and a quiet hum is heard from inside. What exactly could have gone wrong? The heating element (heating element) may have failed. The unit waits for the water to heat up to the required temperature and switches to the next mode. Eyelid WB 6106. In washing mode everything happens normally. When it goes into rinse mode, the following happens: water is drawn in and after that the engine turns on, but the speed is too high for rinsing (about 3-4 times more than it should). I have to turn it off immediately, because... the car is shaking. But after turning the button on again, it continues rinsing as it should, that is, at normal speed. This model does not have a mechanical control unit or electronics (there is no display). What could be causing the failure? Most likely, the control unit has failed and requires repair or replacement. Tell me the marking of the drive belt for the model WB 6108 XD, series SZ108611 (the first letter is a little erased, but similar to S), there are no other numbers. Part number 2810970100, belt size 1276 J4. The Beko elb 57001 m washing machine is in operation. When draining the water after washing, a lot of water spills onto the floor, is this a filter? If you recently unscrewed the drain filter, then perhaps it was not screwed into place properly? If the filter is installed normally, then you need to check the drain pipes and the water drain hose. Model elb 57021 ptms, how does it determine laundry imbalance? The imbalance is determined by the engine tachogenerator. Model WKD 25080, purchased in December 2006. I washed everything normally, but recently, when spinning the clothes, it starts knocking, but washes normally. When spinning, I set it to lower speeds, but nothing changed, it also makes a lot of noise. Tell me what's the matter? There may be several reasons for the malfunction: the counterweight, shock absorbers, suspension are loosened, and it cannot be ruled out that the transportation bolts are not turned out. Beko WKD 24500 T. The unit takes in water, starts running the drum, makes one turn and stops, while a sound resembling a soft grinding (whistle) is heard. It sits for a couple of minutes, then the relay clicks, it starts one turn, and stops again. I have to cancel the program, the water drains normally. Heating element, motor, bearings, belt are in good condition. What else could be wrong, the electrician said that the board needs to be replaced, is that really the problem? The control board may be faulty. Washing machine Beko WB 6106, water is slowly filling up, but the drum does not rotate. Please answer, what could be the reasons? There may be several reasons for the malfunction, such as low water pressure in the line or a clogged inlet hose or inlet valve. There may also be a malfunction of the water supply tap to the unit. Washing machine WB 6108 SE. It does not take in water and does not start in modes A and B, but it works in other modes. What to do? There may be a problem with the electronics or the water heating circuit. In a narrow machine wkd 23580, when the drum rotates, an uneven grinding noise is heard. Something got stuck or a bearing. How to disassemble and diagnose it yourself? If the grinding noise is of an “iron nature,” then most likely the tank bearing is faulty. You can check it as follows: with the unit turned off, turn the tank by hand. If you hear a grinding noise, it's a bearing. It is quite problematic to unpress and compress the bearing yourself. Washing machine WKD 25060 R. When washing at 40 minutes during rinsing, it stops with water and does not spin, only clicks after a while, and then switches to pause mode, tell me what to do? Check the drain. The Beko 3450 E model (4.5 kg load) stopped pumping out water and spinning. Can it be repaired and what’s wrong with it? Until the unit drains the water, the program will not proceed to the spin procedure. It is necessary to check whether the drain filter is clogged; if the filter is clean, then most likely the drain pump has burned out and needs to be replaced with a new one. Model WBF 6004 XC. The drum became loose. There is strong vibration when spinning. Is it possible to repair at home? And what is the approximate cost of repairs? An inspection by a specialist is necessary, even if it is confirmed that the bearings need to be replaced, it is necessary to determine whether the tank is installed as an assembly or whether the bearings can be changed separately because This model is not included in the technical documentation. Eyelid WE 6110 SE wash cycle repeats endlessly. The problem is this: when choosing a washing mode, I turn it on. The unit comes to the end of the cycle and continues to wash further. Moreover, the drum has two modes of synthetics and cotton, and this drum spins endlessly. And it does everything according to the program without failures. It looks like this: the first thing in parentheses is that cotton wash (wash) - cotton spin (spin) - synthetics wash (wash) - cotton wash (wash) and so on endlessly. Those. It works in all modes as it should, but it doesn’t stop. If you described the problem correctly, then there is a breakdown in the timer. Beko WB 6110. Does not heat water. We are thinking about a heating element, but it’s not clear which side to start disassembling in order to get to it. The heating element is located at the bottom of the tank. SMA WMD 25080 T, you need to reboot it. How to do it? The program is reset when the programmer is set to position “0” when the unit is turned on. When you turn on the start of SMA 5350 T, the indicator of the open door does not go out, the door does not close (that is, that is) and washing does not begin accordingly and goes into the pause mode. Replace UBB and work. I have such a problem with Beko 3500 D. After washing, they decided to put another wash, but she did not work. All three bulbs below and one top were displayed on it. To launch/pause and does not react to anything. I tried it on/off. - useless. Then I made out the motor - it is in order, there is still brushes, the pump is normal. I called all the contacts, the same is normal, I don’t even know what to do. If the motor is working and there is no closing of windings, the brushes are in order, then the control module must be checked. When turning on, the squeeze is immediately turned on, the unit is erasing, but neither additional rinsing nor other additional functions work, since the light bulb is burning, what could be? Do you mean that the push -up button lights up and burns all the time? On certain models, this happens when a reduced speed of spinning revolutions is selected. Then this is a completely normal phenomenon. Additional functions should be selected before the washing. Everything is carried out and connected, I do not know correctly or not, but the indicator will light up. There is no water pouring process. What could be spoiled? After the purchase, they turned on for the first time. Question number two - such problems are corrected on the service or is it possible to eliminate them at home? Perhaps too low water pressure. Check the bay, clean the input filter. Open the bay valve. Small -eyed (loading 5 kg) picks up water and that's it. It costs 10 minutes, then the program is turned on and drains water. The reason for the breakdown? After pouring water, according to the program, the unit should start heating water. Most likely, the heater failed, and to avoid a short circuit of the wiring, water is drained. BEKO machine with the function of removal of animal hair. The drum during washing makes a quick circle and stops, as with an annex. Could you help advice? In your case, the following breakdowns are most likely. If the model is quite old, then the electromagnetic engine brushes were most likely erased. This happens from time to time. The control board is faulty. The drive belt slides, which sets the drum in motion.

_________________________________________________________________________________

_____________________________________________________________________________________

Operation of the LG SMA I bought an LG E10B8ND DD washing machine and have only washed it 3 times so far. The problem is this. It washes very quietly, since the all-wheel drive goes directly to the drum. Even spinning at 1000 rpm is quiet, but when it drains...

Samsung WF 8590,6450,6520 We repair the Samsung WF8590NMW8 diamond washing machine (5 kg load). The DE error appears on the display, although 220 is supplied to the lock itself (checked). The most interesting thing is that I decided to test the lock on another SMA, and it worked. Has anyone encountered...

Ariston RSM, WMSF, AVTL Washing machine Ariston avtl 104, with vertical loading 5 kg. The situation is very unclear. SMA can wash off normally, but recently it has started to behave strangely. When rinsing, it stops and the indicator on the power button goes out...

Indesit IWSB, WS, WIU, WIN Machine iwsb 5085, description of the problem. She pours water, the drum rotates for a couple of seconds in one direction, stops, then 2 more times, a couple of seconds each, in the opposite direction and silence. The indicators light up as expected, programs switch, but...

______________________________________________________________________________________

FAULTS AND REPAIRS OPERATION AND SERVICE ERROR CODES

______________________________________________________________________________________

Repair of Bosch Maxx 5 automatic washing machine. Bosch maxx 5 speed edition WLX 20463 OE washing machine in operation. I began to perform the washing program incorrectly. We set the hand wash program, the spin was completely turned off. After washing, SMA switched to rinsing...

Candy Aqua, GVS4, GS3, CS2 There is a smell in the gvs4 126dw3 washing machine. I wash with the addition of liquid Calgon, but there is no effect. Sometimes I rinse my laundry with vinegar. If the linen is thin, like bed linen, then it does not smell. But the towels started to smell. What to do?

Electrolux EWW, EW, EWX The Electrolux EWW 1686 washing machine is in operation. It started tapping when washing, regardless of whether it was spinning, stopping before changing modes, or washing. It knocks periodically, not all the time. The sound comes approximately from the control module...

Zanussi ZWY, ZWSE, ZWT Washing machine zwy 51004 wa, bought about a month ago. I set the washing program, the final spin occurs, and the machine starts washing again, and so on ad infinitum, until you just turn on the water draining program. What could be the problem?

Repair of Ardo SED, TLN, FL Ardo TLN 126. It has a display, and when you turn on the washing program, the washing time is displayed. Gradually it should decrease, but here it is. I turn on the 20-minute wash, but in the end it takes 40 minutes or even more to wash, and the time is constant...

Beko WKB, WN, WKE, WM Model WM 3350 E. We started working in the “short wash” mode, the program worked completely (the door unlock button lit up), but water remained inside. In fact, rinsing and spinning did not work. When I tried to reboot, nothing changed, the sensors...

Repair of ACS Gorenje WS,WT Model WS 43100. The fill valve does not open. Writes "Error 9". This is an error related to aquastop. There is no aquastop. I bought a new non-original valve, took the coils from the old one, put it on with difficulty, one might say, hammered it in. I installed it, did a couple of washes...

Whirlpool AWE, WTLS, AWOC We bought a Whirlpool AWE 6516 washing machine with top loading and electronic control. Container for detergents under the lid. I pour the conditioner into the container, and it immediately pours out of the small...