Dishwasher burning error e4 how to fix

Some of the most popular dishwashers are Gorenje brand models, because they combine sophistication and restraint, versatility and affordability, which is what users like. These kitchen monsters are assembled according to a modern type, so if any breakdowns or other operational inaccuracies occur, error codes can be seen on the dishwasher display. Due to the fact that error codes for Gorenje dishwashers are displayed on the screen, a person can quickly figure out what exactly the fault is and what solution may be appropriate.

The list of encryption errors for dishwashers is small; it can be easily found on the Internet, which will help you call a technician in time and save the device from permanent breakdown.

Gorenje dishwasher error codes

This manual is designed to help you find faults and solve problems associated with the breakdown of Gorenje dishwashers.

It often happens that an error on the PMM display appears due to the breakdown of some part, and its solution requires repair, and not just entering a service test, which is carried out by technicians during the initial diagnosis.

Next, we will look at the main errors of Gorenje dishwashers and give brief comments that will help in troubleshooting problems indicated by one or another code.

Is it worth taking on the repairs yourself?

If the user is not very good with electronics, then an accurate diagnosis of a dishwasher breakdown, as well as proper repair of it, is beyond the power of a person. In order for the Gorenje dishwasher to be saved and the error code no longer pops up on the screen, the owner of this modern household appliance should follow these steps:

• If you find an error code on the display, completely disconnect the device from the electrical power supply,
• contact a qualified technician and ask him to come to carry out diagnostics,
• listen to the opinion of a specialist, if necessary, pay for repairs or replacement of parts.

Trying to save a little, a person who does not understand anything about electronics can only make the device worse and completely disable it. Of course, another solution to the problem is also possible. The user can tell the technician the error code and, under his strict guidance, over the phone, view the status of the device, after which the technician will decide whether the situation requires his presence or give advice on what to do next.

To prevent error codes from popping up on Gorenye dishwashers, you need to carefully care for them and use them correctly, without overloading them with detergents. It is necessary to use the device according to the instructions, then it will break down extremely rarely and will be able to perform all its options correctly. If a breakdown does occur, then users who are unsure of their abilities and knowledge should immediately call a specialist. Often such errors are caused by simple inattention or some minor problems, but there are also more serious problems that require professional intervention and expensive repairs. It is possible that the system simply malfunctioned, and it will function normally after a restart, which should also be checked. There are not so many errors, but each of them can indicate a number of possible breakdowns.

Source of the article: https://comp-plus.ru/bytovaya-tehnika/oshibki-posudomoechnyh-mashin-gorenje-kak-ispravit

How to decipher fault codes for Gorenye dishwashers

First, let's look at how errors are displayed on models with an LED panel and with LCD displays. Depending on the dishwasher model, you will have to decipher what the alphanumeric code or a certain combination of light bulbs means.

Gorenje dishwashers - a little about the advantages

The modern Gorenje dishwasher is a high-tech and stylish kitchen assistant that has the following number of advantages:

• has enough space for washing kitchen utensils of any size,
• the ability to place baskets on one of several levels,
• presence of very good capacity parameters,
• you can load up to 14 sets of dirty kitchen utensils into the dishwasher at a time,
• Ideal for washing long and short kitchen utensils,
• effectively washes kitchen utensils over the entire area, even in hard-to-reach corners,
• after finishing work, it issues perfectly clean and dry dishes,
• the door of models of the specified brand opens automatically, which makes it clear to the person that the washing is complete and the need to pick up cutlery,
• these models have the highest quality protection against leaks compared to options from other brands,
• the machines have a convenient external device that greatly facilitates the installation process,
• models of this brand are economical and operate in virtually silent mode,
• Gorenje machine filters are self-cleaning, which greatly simplifies the life of their owners,
• after washing, the dishes are completely hygienic, there is no visible dirt or harmful bacteria left on them,
• The devices can determine for themselves which mode is best for washing in a given case.

As it has already turned out, Gorenye dishwashers are spacious, high-tech and convenient, which is why they are popular. Many homes have such machines, and it’s worth getting more detailed information about their error codes, as well as troubleshooting options.

Meanings of error codes and recommendations for troubleshooting Gorenje breakdowns

Below we list the designations of fault codes that the user may encounter when operating the Gorenye dishwasher. In the tables below, the causes are presented in rating form, starting from the problem with the greatest probability and ending with the least.

E1 – activation of the leakage sensor and detection of water in the tray

Appears if the float sensor of the “Leakage Protection” system is closed for more than 3 minutes, if water leaks into the pan. In this case, the pump will operate until the element contact opens.

Water entered the pan due to a leak in the tank from the Aquastop system hose.

Drain the tray so that the contact of the tank full sensor opens. This is followed by restarting the dishwasher to check and find the location of the leak.

A malfunction of the electronic board is obvious if none of the four failures listed above are confirmed.

How to reboot the machine to determine the module failure:

· select the washing mode;

· close the loading hatch;

E2 - the level sensor of the Gorenye dishwasher has tripped

The system signals error E2 if the water level has crossed a certain mark and an overflow is detected. The Gorenye dishwasher stops the user-specified program, starts the pump to drain the water, and displays an error on the display (or the indicators flash).

Important! To immediately rule out a failure of the control board, you need to carry out the following check:

After emptying the dishwasher tank, check the operation of the pressure switch using an ohmmeter.

Select a mode and turn it on. Make sure the pump delivers water evenly without creating bubbles.

If the water supply is intermittent, you need to inspect the pump hose that passes through the pan - it may be clogged.

The repair involves closing the water valve to regulate the pressure of the water flow. After this, reboot the device several times to make sure the problem is resolved.

E3 – no heating

Warning lights or an error code appear on the user panel when the water heats up too slowly - less than one and a half degrees in 20 minutes.

Using a tester, measure the resistance of the fuse. If “0” lights up on the device screen, it means “closed”, there is no operation. If the measurements report: “open,” then the fuse has tripped to protect the heating element from overheating and burnout.

In the latter case, the thermal fuse trips due to one of two possible reasons:

1. The thermistor position is broken.

The heater should be checked using an ohmmeter. Measure the resistance by applying the probes of the device to the contacts.

Perform wiring maintenance by checking the integrity of the connections on the dishwasher parts and its control module.

If the washer pump stops working, water stops circulating in the system and therefore does not heat up (at this moment the heater thermal fuse could have tripped).

If the above breakdowns are not confirmed, this may mean that the relay that controls the operation of the heating element was broken.

Using an ohmmeter, measure the voltage at the heater connector as it heats up. At this moment, the terminals should produce 220 Volts.

E40 – the temperature sensor circuit is broken

You will see this code when the PMM is turned on and the sensor is not working. Malfunction is rare if the dishwasher is used correctly. A failure often occurs as a consequence of previous repair work - wiring maintenance or replacement of a module or detergent dispenser.

To solve the problem yourself, try using our recommendations.

Armed with a multimeter, measure the resistance of the thermostat - it should be at the level of 12 kOhm at a room temperature of 20 degrees.

E5 – the dishwasher does not fill with water

This code usually lights up when water is filled into the dishwasher if the required level is not reached within a 7-minute period.

Check whether the fill hose in the PMM is not pinched. Also inspect the filter mesh on the machine body, at the hose inlet.

Check the integrity of the connections between the intake valve and the electronic board. Run the tester in ohmmeter mode to measure the resistance and check if the connections are OK.

It is necessary to check the coil with a tester.

If the wiring is fine, take a tester to check the voltage at the solenoid valve.

E6 – no draining

Alarm code “E6” lights up when draining if the tank is not emptied within three minutes.

Check the operation of the drain pump. You will need a tester to check the resistance at the connector where there should be no breaks.

Check with a tester whether the pump receives voltage from the block when draining - it should be 200V.

If the operation of the part is not impaired, but its signals that the tank is already empty do not reach the module, the electronic board may fail.

E9 – overflow

This code requires a complete check of the hydraulic system of the Gorenje dishwasher. Pay special attention to the situations listed in the table.

Run the wash cycle to check how evenly the water flows. It is possible that the pump hose is clogged.

Important! In Gorenje electronic boards with 3 and 5 buttons (first generation of screens), the E9 code does not light up.

Now you know everything and even more about the errors of Gorenje brand dishwashers. You will be able to provide all possible first aid to the damaged equipment and save on diagnostics when calling a technician.

Source of the article: https://cosmo-frost.ru/posudomoechnye-mashiny/kody-oshibok/kody-oshibok-posudomoechnyx-mashin-gorenje/

Error E4 in the dishwasher: what to do, how to fix it, Dishwasher burning error E4, how to fix it.

What to do if each of their codes is detected

When detecting an error code on the display of a dishwasher, not every consumer can quickly and correctly navigate what to do in such a situation. So that the user does not face a feeling of confusion and is able to save his kitchen appliances, it is worth reading the action guide, which is written for each code separately. So, if the machine signals problems using the E1 code, then you need to act according to this principle:

• completely disconnect the dishwasher from the electrical power supply,
• stop the flow of liquid into the dishwasher,
• perform a detailed check of the condition of the pallet,
• look under the dishwasher body to find out if there is actually a leak,
• restart the mechanism again and see if the same code appears again,
• if the error does not disappear, you should remove the side panel from the device, pull out the pan and drain the water from it, track the source of the leak and fix it, if you need to change the gasket or pipe, complete the process, assemble the machine and start it up.

Only those who understand repairs can carry out such actions, and if a person does not have the necessary knowledge, then they should seek help from a qualified technician.

Knowing how to fix a breakdown with code E2, you can also begin to fix error E9, because they are essentially the same. So, when the presented dishwasher malfunction indicators appear on the screen, the consumer needs to act according to the following scheme:

• The dishwasher should be completely isolated from the power supply,
• The water supply to the dishwasher must be completely shut off,
• reboot the device several times in a row, seeing what happens during this time,
• unhook one of the walls of the housing to check the condition of the pallet,
• if you find a dry sump, find the blue wire and properly disconnect it,
• connect the machine and check whether it drains water (if it drains, then problems with the control module can be completely ruled out; if there are problems, most likely the control board has failed),
• Call a technician to repair or replace the part.

Most often, to eliminate this malfunction you need to call a specialist, since the repair is quite complex and requires special knowledge and appropriate tools.

The following instructions will tell the consumer what to do in the event of a breakdown with code E3:

• check the temperature of the water at which kitchen utensils are washed,
• unscrew one of the walls and the protective panel located under the door,
• check the operation of the temperature sensor and heating element,
• use a device called a multimeter to carry out detailed diagnostics,
• check the condition of the fuse, as well as the resistance level that the heating element currently has,
• check the thermistor and wires, if any of the parts require replacement, replace it,
• additionally test the condition of the control module.

Again, all diagnostic and repair processes must be performed by a qualified technician.

You can solve the error that is encrypted with E4 code by following the steps below:

• remove the panel and check the condition of the temperature sensor,
• inspect the wires that lead to the temperature sensor and evaluate their integrity coefficient,
• if necessary, replace the wires or install a new temperature sensor.

If everything is in order with the specified part and wires, then we can assume that there are specific problems with the electronics and they should be addressed by a professional technician.

The display of error E5 on the dishwasher screen indicates a lack or complete absence of water, so this problem will have to be solved in this way:

• check the inlet hose to find out if anything is pushing through the fluid supply system,
• check whether there is water in the house at all, whether its supply has been turned off,
• check the inlet duct to see if there are any blockages,
• check the resistance of the intake valve using a special device for this purpose,
• diagnose the wiring that supplies the valve.

If all options have been checked and no failures are observed in this area, then there are electronic failures that should only be addressed by a professional.

When a user approaches his Gorenje dishwasher and sees error E6 on its display, most likely the following actions need to be performed:

• check the level of contamination of the device's garbage filter,
• carefully inspect the siphon and drain hose of the dishwasher to identify the presence of squeezing or blockages,
• disconnect the dishwasher from the power supply and carefully remove one of the side panels,
• check the wiring, drain pump and pressure switch to identify damage and other problems,
• To properly diagnose the condition of the device, use a working multimeter,
• If malfunctions of one or another part are identified, it should be properly replaced.

The occurrence of one of the listed errors may indicate the presence of a minor malfunction or a serious problem, so it is better to ask a professional to carry out an accurate diagnosis to determine the exact cause of such an electronic reaction.

What does error E4 mean in a dishwasher?

Modern household appliances, including dishwashers, are crammed with electronics. Its work is connected with a huge number of sensors that control the entire work process. When one of the nodes fails, the sensitive element transmits a signal to the electronic unit. The work process is blocked. To make the reason clear to the owner of the equipment and the technician, the machine displays an error code on the display. If the dishwasher writes code E4, this means that there is a problem with the water.

The error code indicates that there is too much water in the tank.

A certain amount of water enters the dishwasher tank. If it is more or less, the automation blocks the work. It is error E4 that signals that the tank is full.

If you have no experience in handling equipment, you should not make repairs yourself. It is better to use the services of a service center. However, the work of a master will cost about 8 thousand rubles. A dishwasher breakdown is not so serious that it cannot be dealt with by a person who knows how to use a screwdriver and pliers.

What to do to fix the problem

Before you begin to repair or replace faulty elements, you need to exclude a system failure: when the board mistakenly displays a malfunction. Try resetting the code. For this:

• pull out the PMM plug from the socket;
• wait 10-15 minutes;
• start the equipment.

Look at the Hansa dishwasher screen. If the icons light up again, you need to look for and fix the problem. First of all, check the pressure switch (level sensor), since it is responsible for the amount of water in the hopper. When it gives incorrect readings, the water may overflow.

In some models, the PMM installs a flow sensor instead of a pressure switch.

Let us describe the general sequence of actions:

1. Disconnect equipment from the network and communications.
2. Remove the camera from the baskets.
3. Turn the machine over onto its back wall.
4. Remove the panel from below.
5. A plastic box with tubes is attached to the circulation block.
6. To check its functionality, attach the multimeter probes to the contacts and measure the resistance. If the value drops to zero, the part is working.
7. If there is a malfunction, replace the sensor.

The inlet solenoid valve is equipped with a diaphragm. When turned off, the membrane blocks the passage, but as soon as the valve receives an impulse, the partition opens and water is poured in. The cause of the breakdown may be mechanical or electronic.

To diagnose the mechanical part, operating voltage is applied to the valve to check whether the membrane is working or not. Diagnostics of the electronics of the Hansa PMM is performed with a multimeter.

The valve is easy to replace. It is enough to disconnect the wiring chips and unscrew the fastening screw.

This is how you can fix the problem with your own hands when code E 4 appears. Read more about how to replace the pressure switch in a dishwasher in our separate article.

Source: cosmo-frost.ru

Reasons for error E4 in the dishwasher

Any type of dishwasher is equipped with an aquastop. This is an emergency system that is triggered when the pan is overfilled with water. As a result, error E4 appears on the display. The situation arises for several reasons. To find out, first the pan of the car is cleared of dirty water.

Troubleshooting is done in the following nodes:

1. Drainage pipes, hoses and other elements of the drainage system. They may become thin.
2. Error E4 will occur if the inlet hose plug fails.
3. If the drainage tube breaks off from the pump, it will pump water not into the sewer, but back into the machine. The rubber tube can come off when the clamp is loosened
4. A malfunction of the pump itself results in the car flooding.

To find out why the dishwasher gives error E4, open its case, check all elements of the drainage system and the functionality of the pump.

Errors 0E, 0F, 0C, E3 on a Samsung washing machine

What's happened

The washing machine display showed an error message “0E”,

In models without a display, the indicators for all washing modes + two lower temperature indicators light up.

What does an error mean?

There is too much water in the car.

Why did the error appear?

● The drain hose is not connected correctly to the sewer;

● The water fill valve is blocked in the open position.

What to do next

Unplug the machine. 2 Disconnect the drain hose from the sewer (siphon, pipe). If you extended the drain hose, remove the part that was extended. 3 Place the end of the drain hose into the bathtub or sink. 4 Turn on the machine and run the same wash cycle.

Do not wait for an error to appear if the machine has filled a full drum of water. Stop the wash by pressing the Start/Pause button and submit a repair request.

If the error does not appear, it means the drain hose was connected incorrectly. To ensure that the machine operates without errors, properly connect the drain hose to the drain.

The sound of water pouring is heard

If you hear the sound of water filling, but the machine still gives an error, then:

If there are not many things loaded and there are no things that absorb a lot of water, then check the water pressure through the inlet hose. If the pressure is weak, an error will appear. In this case, contact a plumber.

How to fix error E4 in a dishwasher

It is impossible to find out the cause of error E4, much less carry out repair work, without disassembling the machine:

1. The dishwasher is disconnected from the power supply by removing the plug from the socket.
2. The tap is blocking the water supply to the machine. Disconnect the supply hose from the shut-off valve.
3. Error E4 displayed on the display indicates that the pan is overfilled. Therefore, the dishwasher must first be emptied of water. To do this, use a bucket, scoops, rags, and other devices.
4. When all the liquid has been eliminated, containers for storing dishes are pulled out of the dishwasher hopper.
5. The car is pulled out to a spacious place and laid on its side.
6. Using keys and a screwdriver, unscrew the nuts, screws, and self-tapping screws that secure the back and top covers, as well as the tray. After dismantling these parts, all components of the machine will be freely visible.
7. To find the cause and eliminate the E4 error in the dishwasher, the first step is to remove the aquastop.

Thanks to the operation of the aquastop sensor, flooding of the room with water is eliminated in the event of a machine breakdown

After dismantling the Aquastop sensor, they begin to search for the cause of the E4 error code and identify the damaged unit.

The first step is to inspect the dishwasher pump and the hose connection to it. The pump is installed conveniently in a visible place. If disassembly is necessary, you will not have to take photographs or write down on paper the order of the parts.

If the cause of the leak is a hose that has flown off, do not rush to put it on the pump nozzle. On the reverse side of the drainage element, loosen the clamp. The hose is removed from the machine and inspected.

To diagnose the internal condition of the rubber tube, it is removed from the pipes of the drainage system units

The cause of the hose failure may be a blockage. Most often it occurs from solid deposits of salts if the water supply is hard. Particles of fats and detergents settle on the walls of the hose. When the passage hole narrows, the clamp is not able to cope with the resulting excess pressure. The hose breaks, the pump begins to pump water into the pan, the dishwasher shows error E4, after which the aquastop blocks the operation of the system.

A clogged hose is cleaned with acidic agents and mechanical devices. If this cannot be done, buy a new part.

If the hose is not torn off, and the dishwasher displays error E4, there may be a crack somewhere or a loose clamp. The second problem is easily fixed. The clamps just need to be tightened. It is impossible to fight cracks. The hose is just being changed.

After eliminating the cause, everything is put back into place, except for the covers of the machine body. It is connected to the water supply, electrical network, and checked for functionality. If the leak does not recur, the dishwasher is working, the repair was successful. The lids are put in place.

How to fix the problem

Before troubleshooting, rule out a system failure. To reset icons from the screen, do this:

• pull out the PMM plug from the socket;
• After 10-15 minutes, reconnect.

If this doesn't help, inspect the parts.

Check the intake valve.

It is usually located at the bottom of the case:

• close the shut-off valve;
• disconnect the inlet hose - be careful, water may flow from it;
• there is a valve behind it - look to see if its contacts are burnt;

• check the mechanical part by applying an operating voltage of 220 V to the coils of the part. Does the membrane open and close? This means the element is working.

In the event of a breakdown, the membrane is stuck in the open position, so water flows without stopping.

In the event of a malfunction, complete replacement of the valve will help.

To do this, disconnect the wiring chips and unscrew the fastening bolt. With the old element, you can go to the store to find a suitable replacement. Installation is carried out in reverse order.

To diagnose the pressure switch, you will have to disassemble the car.

In Bosch and Siemens models, it is connected to the circulation pump. Therefore, the approach to the part is carried out through the bottom of the equipment.

We wrote about how to replace a level sensor in a separate publication. The check is simple: inspect the wiring. If there is a malfunction, the sensor must be replaced.

Do not be alarmed when you notice error E 4 on the Krona dishwasher screen. Now you have the meaning and decoding of the code - you can fix the problem yourself.

Due to the growing demand for dishwashers in Russia and the CIS countries, an increasing number of users are wondering what to do in case of problems, such as water leakage or, conversely, . Modern devices are equipped with a warning system, and in the event of a certain type of malfunction, a digital code will be displayed on the display. Each model has its own system.

This code is typical primarily for Hansa brand dishwashers

Error e4 is one of the most recurring errors in dishwashers. To eliminate it, you will first need to find out the reason for its appearance, which will be discussed in this material.

Fixing error e4 in the dishwasher

Due to the growing demand for dishwashers in Russia and the CIS countries, an increasing number of users are wondering what to do in case of problems, such as water leakage or, conversely, the dishwasher does not fill with water. Modern devices are equipped with a warning system, and in the event of a certain type of malfunction, a digital code will be displayed on the display. Each model has its own system.

This code is typical primarily for Hansa brand dishwashers

What error codes are there and what do they mean?

The standard option for indicating dishwasher malfunctions are codes consisting of one English letter and one or more numbers. For machines manufactured by Gorenje, fault codes begin with the English letter E, followed by only one digit. This dishwasher has the following codes indicating problems:

1. E1.
2. E2.
3. E3.
4. E4.
5. E5.
6. E6.
7. E9.

Each option has its own meaning, informs about a specific problem, and also suggests in what specific way it can be solved.
The appearance of the E1 code on the display of a modern dishwasher is accompanied by the blinking of the first and last light on the control panel. This combination notifies the owner of the dishwasher that the built-in leakage sensor has tripped and the water supply has been stopped. Since the machines are high-tech, they block the flow of liquid to avoid flooding the kitchen.

When the second and last light sensor flashes on the screen, and the E2 code pops up, the user should know that the overflow mechanism has worked. The sensor warns that the incoming water level is excessively high.

An error that is encrypted with the E3 code value is additionally manifested by the blinking of the first, second and last light sensors. Such a notification will notify the consumer that water heating is not being performed, which means that there are specific problems in the system responsible for this process that require diagnosis and elimination.

The blinking of the third and last light sensor indicates the presence of error E4. This encryption indicates the fact that the thermistor is not functioning correctly or is completely broken. To be more precise, the problem most often lies in a broken thermistor.

If three sensors on the dishwasher light up, namely the first, third and last, then the display shows error E5. This code indicates that water has stopped flowing into the dishwasher, which means you should think about clogged pipes or some other problems in this area.

The flashing of the second, third and last light, as well as the display of fault code E6, hints to the consumer that the drainage is not being performed and that the dishwasher system responsible for this process needs to be diagnosed. If the first and last light comes on, and error code E9 appears on the Burning machine screen, it means the overflow sensor has worked and there is too much liquid in the device.

Decoding the code

Error code e4 in a dishwasher means “too much water.” This may mean that one of the pipes is leaking, or the plug on the inlet hose has become unusable, which is why liquid has accumulated in the tank with a volume exceeding the permissible norm. You can repair this fault with the help of a specialist or with your own hands. However, the services of a specialist are expensive - about 8 thousand rubles, so it will be easier to do the repairs yourself.

When error e4 occurs, the aquastop emergency system is activated. This means that the pan is full, and now it’s impossible to do without at least the initial draining of all the stagnant and non-flowing water. This is an initial measure and in order to understand how to fix error e4 in a dishwasher, you will first need to disassemble it and repair the broken parts. Next, we will look at the possible causes of leaks inside the machine and ways to eliminate them.

Possible causes of leaks inside the dishwasher

It is difficult to understand the reasons for the error without opening the housing and checking the sockets, pump and other elements of the drainage system. However, here it is necessary to mention the most common of them:

1. Hose coming off the pump
2. Leaking drainage system pipes
3. Pump malfunctions

A slipped pipe as a possible cause of dishwasher flooding

How to disassemble a dishwasher

So, you can fix equipment problems either by repairing parts or replacing them with new ones. To do this, you should disassemble the dishwasher according to the following scheme:

• Disconnect the plug from the socket;
• Shut off the water supply to the water pipe to which the inlet hose is screwed, then unscrew the securing clamps;
• Prepare a floor bucket and rags in case there is water left inside the machine;
• Remove all containers for dishes from the machine hopper;
• Carefully place the machine on its side;
• Using a screwdriver and wrenches, unscrew the fixing screws holding the back wall, as well as the tray. Don't forget to also unscrew the top cover. Now you can not only inspect the pump, but also inspect all the other “insides” of the dishwasher;
• Now remove the aquastop from the machine. This device blocks the uncontrolled release of water in the event of a system failure. In many ways, it is thanks to the aquastop that it is possible to avoid serious leaks during error e4;

Diagram of a pump with aquastop

Important! The old generation Aquastop often ignores small leaks that form as a result of small tears in pipes and hoses, which is why the indicator that lights up when there is a leak will not light up. In this case, you will have to identify the error the old fashioned way - check whether there are any puddles left after the cycle, since leaks can be very insignificant at first.

Now that the sensor has been removed, you can proceed directly to the repair and installation work. The main advantage of the location of the pump is that you do not have to completely disassemble the machine and do not have to photograph the disassembly process itself, since the location of the walls, panels and ceilings is easy to remember.

What do these or those codes mean?

To begin with, it is necessary to say that Gorenje dishwashers are still available in two versions: with and without a display. All machines have a self-diagnosis system, but it interacts with the user differently. So, let's start listing the fault codes.

The water heating temperature is set by a program embedded in the control module and can be adjusted by the user. The module monitors the actual heating temperature and compares it with the value specified by the program.

What to do if a leak occurs?

When code E1 appears, the user must immediately turn off the power to the dishwasher, turn off the water supply to it and check the tray. Perhaps there really is a lot of water in the sump, or maybe the leakage sensor just worked idly. Both can happen with equal probability. True, you can look under the body of the Gorenje dishwasher. If it is wet there, it means there is still a leak. What to do in this case?

If there is no water in the pan and the sensor does not want to work, it can be replaced. But first, you need to “ring” the wiring that communicates with this sensor with a multimeter and, probably, test the control module. If the tire responsible for interacting with the leakage sensor has burned out, you will have to contact a technician so that he can professionally eliminate this unpleasant defect.

Overflow of water

Having witnessed the appearance of code E2, E9, the user should not turn off the power to the machine and turn off the water supply. Instead, you need to reboot the machine and see how it behaves. It is necessary to repeat the reboot several times in order to completely eliminate a short-term system failure.

Next, you need to turn off the Gorenje dishwasher, unhook the right or left wall of the case, and then check the tray. If the pan is dry, disconnect the blue wire from the pressure switch. Next, we connect the machine and turn on the very first program. If the machine begins to drain water, it means that the control module can be excluded from the list of possible problems. If the machine starts pumping water, it means the control board is broken.

The second situation does not necessarily require replacing the control board. You need to call a technician who will reset the firmware or reflash the board. In more than half of the cases, this is enough to restore control.

If we have excluded the control module, we need to remove the thin rubber hose from the pressure switch tube and carefully inspect it. Pressure must be maintained inside the hose, and if there is even the slightest damage to it, it must be replaced. Also inspect the level sensor tube. Small debris may accumulate in it, which needs to be cleaned out. Check the resistance of the pressure switch, and also check its wiring.

If everything is in order, then the last thing you need to inspect is the inlet hose. In slightly more rare cases, the pressure switch begins to work incorrectly or refuses to work due to a blockage in the inlet hose. Due to the blockage, water begins to flow unevenly. Air bubbles form inside, which ultimately enter the hose and tube of the part, interfering with its operation. By removing the blockage, you will restore normal operation of the system.

The water doesn't heat up

Code E3 lights up on the display; you should pay attention to how cold the machine washes the dishes with water. In winter, this is especially noticeable, since simply icy water accumulates at the bottom of the washing chamber. If the water inside is hot, this indirectly indicates a breakdown of the control module, which incorrectly reads the readings from the temperature sensor. Well, let’s not talk about sad things ahead of time. To begin, let's do the following:

In such a situation, failure of the control module also cannot be ruled out. If, after doing all of the above, you do not find any defects, you can invite a specialist to test the electronics. You shouldn't do this on your own.

Thermal sensor does not function

Error code E4 specifically indicates that the temperature sensor requires repair. However, there are nuances here too. The temperature sensor may actually be broken, or perhaps the wiring leading to it may be broken. The contacts may also burn slightly, or the control module may fail, which will no longer recognize this part.

We will try not to think about possible problems with electronics for now; we will check the temperature sensor and wiring one by one with a multimeter. Depending on the identified problem, we replace the sensor or the broken wiring.

No or not enough water

Error E5 appears if the machine does not draw water at the proper speed or does not draw it at all. First of all, you need to see if the inlet hose is pinched. It may be that the water utility has turned off the water supply, so water is not flowing into the machine. Having eliminated elementary errors, we move on to identifying more complex defects.

At the same time, it is worth checking the inlet valve for blockages. Quite often the valve mesh becomes clogged and due to this defect the valve cannot operate normally.

Through the side wall we get to the intake valve and check its resistance with an ohmmeter. If the valve is functioning normally, you should also check its supply wiring. Failures in the electronics of the dishwasher cannot be ruled out.

Waste water does not drain away

When you start the waste water discharge program, the control module detects the time during which the machine will remove all dirty water from the system. If the water is discharged more slowly than 3 minutes, the control module will display error E6. We need to look for the reason.

So, we looked at what the various Gorenje dishwasher error codes mean and, most importantly, we looked at how to fix these errors. Try to look for defects yourself, but be reasonable. If you cannot identify the problem yourself, feel free to contact a specialist. A qualified specialist will definitely help you. You may also find the information from the publication Dishwasher Repair Gorenje useful. It describes some of the nuances that we omitted in this article. We want to end here, thank you for reading the text to the end. Good luck!

We are looking for the cause of the problems

After disassembling the machine, collect all leaked water with rags in a bucket and begin inspection. If you find that the hose connecting the pipes to the pump has fallen off, loosen the clamp securing it on the back side and inspect the hose from the inside.

Pumping system with aquastop

It often happens that the reason the hose comes off is a critical level of pressure. This may be caused by a blockage in the hose itself or at the place where it connects to the pipes. This can be caused by various types of blockages. For example, scale - residues of mineral salts and other chemical elements settling inside the machine. Over time, the salts harden and can form a solid barrier. This can lead to failure of the entire drainage system, so it is best to take preventive measures - add special salts to soften hard water when starting the dishwasher. Otherwise, this may lead to a major breakdown that cannot be fixed on your own, and you may have to purchase a new dishwasher.

The second possible cause of problems recognized by the system under code e4 is a leak in one of the pipes or hoses in the drainage system. It can leak at the junction of hoses and pipes, or from holes in the body. In the first case, you just need to re-tighten the clamps or change the rubber gaskets, which are commercially available in plumbing stores. If you find a leak on the body, then you will have to replace the spare parts. Do not tighten it with tape or tape - this can lead to more serious problems in the future.