How to disassemble an Electrolux dishwasher. Repair of Electrolux dishwashers at home: typical faults and their elimination. Electrolux dishwasher malfunctions

Preparing to use the dishwasher

If you have a built-in dishwasher, disconnect the fastenings, disconnect the communications and remove it to a free place.

Do the same with the freestanding model. But the compact machine, which is located on the table, does not need to be pulled out. It is enough to put it in a comfortable position.

Take care of the tools:

crosshead screwdriver;
pliers;
awl.

To carry out work quickly and efficiently, it is important to understand the location of parts in the housing. You can read how a dishwasher works in a separate article. We will remind you of the main components:

baskets for dishes;
upper and lower sprayer;
float sensor;
drain filter;
drain pump;
heater;
circulation block;
inlet valve;
control module;
additional drying heating element.

How to remove the lid from a Siemens dishwasher?

Siemens dishwashers are quite easy to disassemble, but difficult to assemble. If you are not going to repair it yourself without the appropriate education, then this process will not complicate you. A feature of Siemens brand machines is that there are different options for loading laundry, so this factor must be taken into account when removing the lid. If front loading then proceed as follows:

There are two screws on the back, look at them;
Unscrew them;
Please note that it is necessary to preserve the clamps, otherwise the operation of the device will noticeably deteriorate.
The fasteners are loose, carefully remove the cover.
Set it aside;
Start another process for which the lid was removed.

Agree that removing the cover is half the battle. But now you know how to remove the lid from a Siemens dishwasher.

The main causes of failure of the Electrolux PMM

There are typical problems that are specific to Electrolux brand models. Their appearance, as in other dishwashers, is influenced by several factors:

Incorrect operation of the device. Chamber overload, food residues on surfaces, lack of filter cleaning.
Use of low-quality detergents.
Power outages. Surges cause electronics to burn out.
A large number of impurities in the water. When heated, potassium and magnesium salts settle on the heating element and other parts.
Factory defect, poor quality assembly.

Few people complain about the workmanship. Almost all Electrolux models entering our market are assembled in factories in Poland. But the duration of operation is influenced by the factors mentioned above.

Such malfunctions occur most often due to:

Problems with water supply and drainage. Tract blockages.
Heating problem. The water does not reach the set temperature.
Poor washing quality.
Problems with electronics, programs freezing, failure to turn on.
Leaks.

The self-diagnosis system helps to accurately determine the cause of the breakdown. The manufacturer has foreseen possible problems, so if there is a failure, an error code is displayed on the PMM display. These codes often appear on users' screens:

I10 - water does not flow into the bunker.
I20 - waste liquid is not drained from the tank.
I30 - Aquastop leakage protection is activated.
I60/I70 - problems with the heating element, temperature sensor.
I80/I90 - electronics problems.
IA0 - the sprayer does not rotate.

How to repair a dishwasher with your own hands?

If you have decided where to look for a breakdown, then our recommendations will help you deal with it. The first thing to do when an error occurs on the scoreboard is to restart the program. This will help eliminate system failure. The dishwasher control may malfunction after a sudden power outage.

Unplug the machine;
Wait 15 minutes;
Turn on the equipment.

If the code disappears, it may be due to a system failure. Obvious signs of breakdown require immediate repair.

Fill and drain system problems

The main malfunctions of the tracts occur due to blockages. The inlet filter, like the hose, becomes clogged with debris from the water supply. This is small debris, rust, scale. The filter is equipped with a fine mesh that protects the dishwasher system from debris. To clean the tract:

Close the inlet valve.
Disconnect the inlet hose from the housing. Water may spill out of it, so have a container or rag ready.
Behind it is a filter. Remove it with pliers.

Rinse the parts with warm water; if the mesh is heavily soiled, soak the mesh in a solution of citric acid.

Experts recommend installing a flow filter in front of the hose. It will cleanse the water of salts and make it “softer”.

Behind the filter there is a solenoid valve. When liquid is supplied, it opens the membranes and fills the tank. Voltage drops in the network lead to burnout of the valve coils, as a result of which they stop receiving module commands. If the coils burn out, the entire valve is replaced.

Problems with water supply can be caused by the Aquastop hose. During a leak, its sponge becomes saturated with liquid and blocks the passage. Install a new hose.

The drain path becomes clogged much more often. Poor removal of food residues from the surface of the dishes, infrequent cleaning of the drain leads to blockage, and then to pump malfunction. Damage can be prevented by following simple rules:

Clean dishes thoroughly before loading.
Remove dirt from the chamber at least once a week, or better yet, after each wash.
Use high-quality powders and washing tablets.

How to restore the drain yourself:

Open the bunker;
Remove the dish trays;
Unscrew the filter at the bottom and remove the mesh;

Clean the parts from debris;
Liquid accumulates in the mounting hole - remove it with a sponge;

Remove the protective cover;

Wear gloves and clear any blockage from the pump impeller. Be careful, fragments of broken dishes can block the operation of the impeller.

Disassembly stages

After disconnecting the hoses from the housing, remove any remaining water from the chamber - it may remain in the pan. Open the door and remove all equipment from the chamber. At the same time, remove the baskets and holders.

Do I need to immediately take out the dishes after washing? Wait 10 minutes for it to cool down.

The principle of disassembling dishwashers from Electrolux, Beko and other brands is almost the same. Only some details may differ.

Using the information from our article, you can check and replace any part yourself. Good luck!

Watch the video on the topic:

Source

Overview of the most common faults

In general, dishwashers from the Swedish brand are deservedly considered to be of high quality. Typically, Polish-assembled products are cheaper and break down more often. However, it is noted that Electrolux machines are distinguished by a durable body and a reliable circulation pump. Parts such as filters, gaskets, wiring terminals and other little things are traditionally made at a high level and rarely cause trouble.

Typical breakdowns of this equipment usually include the following malfunctions:

clogging of drainage and water supply elements;
improper heating of water during the specified wash cycle;
failure when executing the selected program, etc.

Very often, the causes of such malfunctions are violations of recommendations for using the device. If problems begin soon after the start of operation or occur too often, you need to check for such violations.

In addition, it doesn’t hurt to make sure that the dishwasher is installed correctly and connected to the sewer and water supply without any problems. The intricacies of installing and connecting a dishwasher are discussed in our other article.

Reason #1 - clogged drain/water supply

Poor quality of tap water is a common problem in many regions. Increased hardness, the presence of mineral inclusions and contaminants have a sad effect on the condition of household appliances, and dishwashers are no exception. For this reason, a filter must be installed before water enters the device.

It needs to be regularly washed, cleaned, and replaced in a timely manner. If damage has developed in it over time, you should not ignore it; you must immediately install a new filter. Otherwise, all contaminants will enter the dishwasher mechanism. Do not think that cleaning with chemicals will eliminate this effect. A reliable filter is essential.

To clean it, you need to follow these simple steps:

disconnect the device from the water supply using the shut-off valve;
find the inlet hose with a filter from the dishwasher pipe, as well as from the tap;
remove filters;
rinse the filters and pipe to remove accumulated contaminants;
install all elements in place and reassemble.

If there is too much dirt, use a brush to clean it. Some owners believe that they can get by with just one drain filter, but practice shows that an additional filter in front of the supply hose will never be superfluous.

In addition, you should periodically carry out preventative cleaning of the dishwasher drain. To do this, you also need to use high quality products recommended by the manufacturer. Cleaning is done only with this product; there is no need to add other chemicals, rinse aid or salt to the dishwasher, and, of course, there should be no dishes there.

We recommend that you familiarize yourself with the features of cleaning a dishwasher at home.

To prevent breakdowns, you must strictly follow the operating instructions.

Here are the basic recommendations for using Electrolux dishwashers:

Before placing items in baskets, they should be cleared of food residues;
Only high quality products should be used for washing;
do not exceed or underestimate the amount of chemicals required for the machine;
you need to ensure that there is a sufficient amount of salt in the appropriate container;
Regularly check the condition of all filters and clean them promptly.

Reason #2 - problems with the water heating device

If there are problems with heating the water during the cycle, most likely a malfunction of the heating element, sensors, or incorrect operation of the control unit is to blame. The weak point of many Western models of household appliances is their high sensitivity to sudden changes in network voltage. Such surges can damage the control board triac; this element will have to be replaced.

To correct the situation, you need to disconnect the dishwasher from the power supply, water supply and sewerage. The built-in machine will have to be completely dismantled. After this, using a tester, you need to check the serviceability of the heating element, as well as all electrical circuits. If you are unable to determine the fault yourself, you will have to contact a service center that has the appropriate diagnostic equipment.

It is not difficult to prevent such a sad situation; just install a voltage stabilizer. The cost of additional equipment will pay off, because replacing the control board will cost much more.

Reason #3 - problems with the command apparatus

With regard to the electronics of the dishwasher, unprofessional intervention can lead to the fact that the situation will only worsen, and you will have to buy a new dishwasher.

A failure of the control module can also result in periodic freezing of the machine during the washing cycle. To correct the situation, you just need to turn off and then turn on the device again. If such a malfunction occurs rarely, there is no need to worry. But when the car has to be restarted over and over again, this most likely indicates a manufacturing defect.

Such a malfunction will have to be repaired by a service center after detailed diagnostics. This is the most expensive type of repair; in some cases, its cost can be comparable to the price of a budget dishwasher. But it also happens that diagnostics reveals a malfunction of a sensor; replacing it will cost much less.

You shouldn’t put off calling a technician “for later” if the car constantly freezes, so as not to worsen the situation. If the owner has experience in repairing home appliances, replacing a sensor or heating element will not cause big problems. Another problem typical of Electrolux dishwashers is deterioration in the quality of washing.

This can occur either due to the fact that the water supply to the chamber is not fully supplied, or as a result of improper supply of detergents. You need to carefully inspect the camera after each wash. If the tablet has not completely dissolved, there is detergent or rinse aid left in the container, all these are signs of problems.

First you need to check whether there is water in the water supply system and whether it has sufficient pressure. Then you should check the condition of the filters and supply hose. If dirt has accumulated there, it will cause poor water flow and problems with washing quality. It is enough to wash it all out for the situation to return to normal. The filters may need to be replaced.

Another source of trouble is a malfunctioning valve in detergent containers. Finally, you need to ensure that supplies are loaded and used in accordance with the manufacturer's recommendations. Limescale deposits accumulated inside the sink and on the surface of the heating element can cause many of the listed breakdowns.

Regular maintenance of the device will avoid costly repairs. The following recipe may be useful: add 250 ml of table vinegar to the detergent container, start the Economy mode, stop the procedure in the middle of the cycle for one hour, then continue washing. This cleaning should be done two to three times a month. We recommend that you familiarize yourself with the five best dishwasher cleaners.

Why might you need to remove the cover?

Removing the top cover may be necessary in several common cases, including:

when integrating the device into a kitchen set;
when repairing faults.

Let's take a closer look at each of the reasons. In many ways, the first reason can arise from a hasty choice. The incorrectly measured distance from cabinet to cabinet, as well as the height, and the dishwasher no longer fits into the kitchen set.

Of course, this problem can only be solved if you remove the top cover of the dishwasher. But it may not be resolved if the lid is not removed. Therefore, carefully consider the choice and parameters, but this is a completely different story. But it should be noted that if the height of the dishwasher is not suitable, then you can simply adjust the height of the legs of the set.

In the second case, everything is also clear, because when during repairs it is necessary to replace a part, you must first get it out. Of course, at the behest of the pike, it will not be replaced on its own, and in order to get it, you need special skills. First, you need to remove the cover, which is what we are talking about.

Heating water

Problems with water heating are related directly to the heating element or to the sensors and control module. This foreign technology is very sensitive to voltage drops in the electrical network, which can cause a triac - a symmetrical triode thyristor in the control board - to burn out.

The control module will not be able to send the necessary signal to the heating element to heat the water - repairing the dishwasher will be expensive due to the volume of work performed:

dismantling the machine to get to the heating element;
diagnostics of it, as well as the entire electrical circuit;
ring the control module, identify the fault and replace it, if possible - remove it and test it in the laboratory.

Advice! To protect your assistant from voltage surges, install a stabilizer between the meter and the machine connection line with your own hands.

Repairs and diagnostics should be carried out by a specialist from the service center; checking yourself may lead to the need to replace the machine with a new one.

Recommendations

To ensure that the built-in machine works for a long time and does not flood your neighbors, listen to some tips in advance:

check for grounding - this will prevent electric shock;
make sure that the drain hose is no longer than 2.5 m - increased load negatively affects the operation of the injection pump;
It is not recommended to install the device under the hob;
To protect the countertop from steam, think about protection; a metal plate is perfect for this purpose.

Now you have an idea of how to integrate a dishwasher into your kitchen. To install equipment in a ready-made kitchen set, you will need not only ideas on where to install the device, but also skills in working with plumbing and plumbing tools.

Number of blocks: 7 | Total number of characters: 8011 Number of donors used: 3 Information on each donor:

Stuck during washing

This defect is quite common on Electrolux car models - technicians advise turning it off for a few seconds and then turning it on again. Sometimes the freeze is repeated systematically; here this method is no longer valid. There is a manufacturing defect: it is necessary to replace the control module and test the operation of the machine in all modes.

Some Electrolux car models are cheaper to buy than to replace a completely expensive control module.

Cases of failure of this component are quite rare; failures are often caused by unstable operation of sensors - aquasensor, pressure switch and the like. Dishwasher repair will consist of replacing them.

Poor wash quality

Machines of this brand quite often have problems with the flow of water or the supply of detergents. In order not to bring Electrolux dishwashers to urgent, expensive repairs, you must immediately diagnose the problem: there is a tablet left, the powder has not dissolved, which means there is a problem with the supply of detergents or water.

Elimination methods:

we check the presence of water in the home water supply system;
look to see if the inlet hose and strainers are clogged;
We examine the serviceability of the detergent supply valve;
We analyze the correct loading of detergents.

After eliminating all the listed shortcomings, the quality of dishwashing should be excellent.

Another piece of advice: don’t be lazy to carry out various preventive maintenance work. At least 3 times a month, add 250 g of table vinegar, turn on the Economy mode, pause in the middle of the cycle and leave the machine in this state for an hour. During this time, the resulting limescale will dissolve completely and without a trace.

Typical failures

According to statistics, 90% of cars under the Electrolux brand that are sold in Russia are manufactured in factories in Poland. Their quality is slightly worse than their counterparts from Germany, but the pricing policy is not bad either. Experts from service centers, especially for Russian consumers, note the following advantages:

reliability and quality of machine body;
well-equipped circulation pumps with a long working life;
During assembly, the main attention is paid to small parts - wiring terminals, rubber seals, filter elements, connecting wires and clamps, on which the trouble-free operation of the equipment primarily depends.

No particularly obvious shortcomings or weaknesses were found, but, like other brands, there are some typical breakdowns and malfunctions from which no one is immune:

hoses and pipes of water supply and drainage systems often become clogged;
The water does not heat up according to the mode;
Sometimes problems may arise with the execution of the specified dishwashing programs.

In order not to frequently repair your dishwasher, you must always pay attention to the condition of the equipment and adhere to the recommendations set out in the instructions.

Disassembly stages

After we have thoroughly prepared for disassembling the Bosch “dishwasher,” you can get to work with a clear conscience.

In order, without skipping anything, we perform the following steps:

Important! When unscrewing the screws from the dishwasher tray, be prepared for some water to pour out of it, but since we laid out rags and cellophane in advance, nothing bad will happen.

If you manage to disassemble the dishwasher before removing the circulation pump, you can replace any broken part yourself. Reassembly must be carried out in strictly reverse order without forgetting anything, then everything will go well.

In conclusion, disassembling a dishwasher is a fairly simple process. Almost anyone can master this kind of work, the main thing is not to forget to screw in all the fasteners and connect all the power wires. Good luck!

Interesting:

Tracts of drain and fill systems

In all technology based on working with water, these systems are the first to become clogged. The water quality is to blame here, because in different regions it not only differs in hardness, but also contains numerous impurities of various minerals.

The first blow is taken by the filter installed at the entrance to the machine: all harmful impurities settle on its walls, so you have to constantly clean it of water stone. No chemical cleaning agents will help you - they only clean the inside of the hoses and pipes of the system.

The algorithm for cleaning the filter element is simple and can be done with your own hands:

shut off the water supply to the machine;
disconnect the inlet hose with built-in flow filter from the tap and the entrance to the dishwasher;
remove the strainer from the housing at the entrance to the machine;
rinse the hose and both filters, then put everything back in place.

Many users do not install an additional filter at the inlet of the drain hose, but in vain - this halves the load on the filter mesh element installed on the machine.

Prevention is the basis for the cleanliness of these elements; such measures for the Electrolux machine are popularly described in the attached operating instructions, but we will recall the main points:

Remove food residues from dishes before placing them in baskets.
Add detergents strictly according to the norm, only high-quality, proven ones, so that their undissolved sediments do not clog the filters.
Make sure you have enough regenerating salt at all times.
After each dishwashing, check both filters at the bottom of the machine tank and clean them of impurities.

For preventative cleaning of the drain system, purchase a patented product, pour it into the bottom of the tank and run the wash cycle on idle without adding detergents.

How to remove the lid from a Beko dishwasher?

To remove the top cover of Beko dishwashers, you must adhere to the following rules:

The cover is attached to the body with two screws; they must be unscrewed. To achieve the desired effect, use a screwdriver.
Put the screws in a safe place so they don't get lost;
First, move the cover back;
Then lift it up.
The cover is off!

It is worth noting that it is often necessary to remove not only the top cover, because for the Veko brand, depending on the situation, it may be necessary to remove the back cover. Therefore, this case should also be considered:

There are only five screws between you and the back cover, so take a screwdriver and carefully unscrew them;
Also remove the screws so they don't get lost over time. Details are important because finding similar ones is harder than you think.
Move the cover without screws at a right angle in accordance with the body;
Release the cover from the grooves.
Pull out the cover.

To summarize, I would like to say that there is no main universal method for removing covers in different models, but there are some general points that are worth discussing again. Firstly, the cover is held in place by two screws. You can usually unscrew them with a screwdriver. Removal occurs either by lifting up or by pulling out of the grooves. The process is not complicated, but may require clarity. For those who want to see once rather than read several times, watch the video.

The meaning of brand equipment fault codes

Many Electrolux dishwasher models are equipped with a self-diagnosis system; they issue a code that can be used to immediately determine the cause of the problem. The message is displayed on the monitor in the form of an error code, for example i60 or i20, etc. If there is no separate display, problems are indicated by a flashing END indicator.

Problems with collecting, draining or heating water are most common.

Here are the codes for them:

i10 occurs if no water flows into the dishwasher chamber within a minute from the start of the cycle, it is recommended to check the condition of the tap, hose (perhaps it is simply pinched), and also clean the filters at the water inlet to the dishwasher;
i20 shows that there are problems with the drain, you need to check and clean the drain filter and drain hose, as well as the drain pump and water level sensors, damaged elements will have to be replaced;
i30 indicates that leakage protection is turned on; you need to drain the water accumulated in the pan and restore the position of the float sensor or replace the hose in the mechanical version of the Aquastop system;
iF01 indicates that water has been entering the chamber for too long, usually this error corrects itself after the end of the washing cycle, it would not hurt to check the water supply system to carry out preventive work;
i60 - a signal about the absence of water heating or about significant overheating, which happens if the heating element has burned out, there is a breakdown in the electrical circuit, the circulation pump, temperature sensor or control board has broken down.

Options for eliminating i60 type breakdowns were described above. In the following video you can watch the repair of a built-in dishwasher that generated this error:

Overheating may occur if there is not enough water inside. In this case, you need to follow the recommendations for the situation with the i10 stake.

The following codes indicate serious electrical, electronic and other similar problems:

i50 – circulation pump triac is broken;
i70 – the heating element thermistor is damaged;
i80 – problems with the control module firmware;
i90 – a malfunction of the control board, which does not allow you to select the operating mode of the device.

Replacing a damaged triac or thermistor is relatively easy. But to reflash or replace the control module, you will have to contact a service center.

Other common problems with Electrolux dishwashers include the following codes:

iA0 indicates that there is no rotation of the indicator rockers, usually this is due to improper placement of dishes in the chamber or due to a voltage drop;
iB0 – transparency sensor failure;
IC0 – lack of communication between the panel and the control board;
id0 – the tachogenerator of the circulation pump is broken, the water does not heat up.

This type of breakdown is complex; you will have to use the help of a service center. Failure codes do not always accurately describe the problem that has arisen in the operation of the dishwasher. It happens that a malfunction occurs due to violation of operating conditions or for some other reasons. If this factor is not eliminated, breakdowns will occur again.

Watch a video on cleaning equipment:

Couldn't fix your machine by cleaning? Then diagnose the pump. The node is located at the bottom of the body. If there is a problem, just disconnect the wiring of the part, turn it and remove it from its place. After this, a new node is installed.

Heating fault

The first sign of heating problems is poor dishwashing. Fat does not dissolve in cold water, so you will remove wet but dirty utensils from the chamber. Diagnostics will help to accurately determine the cause of the problem. You need to check:

A heating element;
Temperature sensor;
Their wiring and control triacs on the board.

Replacing the heating element in Electrolux PMM models is complicated by the presence of a non-separable heating block. Buying a replacement part will cost 3000-4000 rubles. Think about whether the game is worth the candle. If the equipment is already old, it makes sense to add money to a new dishwasher rather than buy a unit.

Have you decided to make a replacement? Then here is the sequence of steps for disassembling the PMM:

Unplug the machine;
Shut off the water supply and disconnect communications;
Remove the baskets from the hopper;
Remove the filter and water at the bottom;
Unscrew the five screws securing the heater;
Turn the body on its side;
Remove the bottom;
The block is connected to a circulation pump;
Turn off the wiring, release the clamps;
Rotate the block and disconnect it from the pump;

Install the new unit in reverse order.

To avoid problems with network outages, connect a voltage stabilizer.
Problems with washing are possible when:
poor supply of detergents;
overloading the machine with dishes;
blocking the sprayer;
circulation pump malfunction.
Check the powder supply simply. Open the cuvette - if the remains of the tablet are visible in it, it means that water is not entering the compartment well. Check the placement of dishes in the hopper. Maybe a large plate is blocking the compartment, or the supply hose is clogged. Clean the cuvette after each wash to prevent detergent from accumulating in it.
Overload interferes with fluid circulation. When one device overlaps another, water does not wash the surface. There must be a gap between the plates for high-quality washing.

The rotation of the rocker arm, again, can be blocked by the plate. There may be a blockage or foreign object in the way. Clean the sprayer holes - nozzles.

After this, the pump is inspected. If it breaks and does not pass liquid, the unit needs to be replaced. The case will need to be disassembled. Remove the bottom, disconnect the pipes leading to the pump. An example of the repair is shown in the video:

Leak in the system

Damage or corrosion of the unit body leads to leakage. Although this is rare, it is not recommended to do any soldering yourself. Such repairs will not last long, so you will have to completely replace the body.

When Aquastop is activated, water may end up in the sump or leak from the hose connections. Inspect the following items:

Hose fastenings. Tighten the clamps tighter.
Pump gasket. If worn, install a new element.
Door seal. Loss of tightness leads to leakage. Open the door, remove the old seal and install the new one.

Check to see if the pallet is damaged. Then it’s better to put a whole stand. If the float sensor malfunctions, a working part is installed.

PMM does not work, does not turn on

The program stops in the middle of the cycle, the dishwasher is plugged in, but does not respond to pressure. These are the main signs of problems with electronics. Try rebooting the system. Did not help? Then check:

Condition of the cable and plug;
Sockets;
Capacitor.

After the inspection, the control board is diagnosed. Sometimes there is no point in changing a module, since it is expensive. Contact a specialist - he will tell you whether it is possible to repair the board.

Most problems can be fixed with your own hands. But some of them require contacting a service center. Follow the operating rules, and then you will not cause your equipment to break down.

What to do if there is no indication in the dishwasher and it does not start

If your dishwasher does not react at all when turned on (even the power indicator does not light up), check first:

Availability of electricity. Perhaps the outlet is faulty, the dishwasher has been knocked out, or there is no electricity in the entire house.
The dishwasher's power plug and cord are in good working order. Inspect the dishwasher's power cord and plug. Before unplugging it from the socket, for safety reasons, it is recommended to turn off the electricity in the apartment at the switchboard. If you notice damage, leave the equipment unplugged and call a professional.

If everything is normal with the power supply to the dishwasher, most likely the cause is a breakdown.

Choosing a location for installation

First of all, it is necessary to determine where the unit will stand. The closer it is to the pipes with hot and cold water, the less communications will have to be pulled. Proximity to a sewer pipe is equally important. The closer the drain, the greater the angle of inclination of the drain pipe. If it is located at a distance of several meters, the length of the flexible wiring may simply not be enough, and waste water containing food waste will stagnate inside in sagging areas.

In such situations, hard plastic or metal pipes are usually used, which makes installation more expensive, but this is the only way to avoid sagging. If the distance is large and the entrance to the sewer is located high, the technician will have to be raised on a pedestal to increase the angle of inclination of the drain pipe. All these troubles can be avoided by placing it near the sink.

Any equipment does not tolerate high temperatures well, so it is better to place it away from the radiator, stove and oven. Proximity to other household appliances is not desirable, but not dangerous either. Electromagnetic fields and static electricity will not cause serious harm to the motor and pump, but their operating life will be slightly shortened.

Electrolux dishwasher

When choosing a location, it is important to consider the location of the outlets and the length of the wire. As a rule, it is 1.5 m. It is prohibited to connect equipment using an extension cord, and installing a new outlet is long and difficult. To do this, you will have to move the wall and pull the wire.

The plug must not be closed tightly. It should always be in plain sight so that if it catches fire, it can be pulled out immediately. Failure to comply with this condition may result in a fire.

Conclusions and useful video on the topic

The process of self-diagnosis and troubleshooting is presented in the video:

Continuation of the video tutorial on troubleshooting:

The third part of the video instructions for repairing Electrolux dishwashers:

Video testing a refurbished dishwasher:

Cleaning the drain and replacing damaged parts, as well as restoring oxidized contacts, are simple repair operations that even a novice technician can perform. But if serious problems arise and the control board needs to be replaced or flashed, you will have to call the service center.