Ardo FLS105: Instructions and manual in Russian

Installing the machine, Leveling the machine, Connecting to the water supply network

II machine installation

Image
Text

INSTALLING THE MACHINE

LEVELING THE MACHINE

Select a suitable location and adjust the machine level using

adjustable legs (Fig. 6). Pay special attention to the choice of location, leveling the washing machine and the degree of tightening of the locknuts.

If the machine is not leveled correctly, it will

unstable, the noise level during operation will be increased, which may lead to malfunctions.

When installing the washing machine on a carpeted floor, you should

Check that air circulates freely between the machine and the floor.

It is not recommended to install the machine in rooms where the temperature

may fall below 0°C.

CONNECTION TO THE WATER NETWORK

▼ The pressure in the pipeline network must be at

range from 0.05 to 1.00 mPa (0.5 -10 bar).

▼ Before connecting the machine, open the tap and

let the water drain to wash away contaminants such as sand or rust from the pipes (this is especially important

value when the washing machine does not work for a long time

used or is connected to a new water pipe).

▼ Connect the inlet hose to the threaded

cold water pipe 3^4″.

Note
In electronic washing machines equipped with a double solenoid valve, connect the red tube to the hot water tap and the other tube to the cold water tap. If the hot water tap cannot be used, both pipes must be connected to the cold water tap using
the special pipe supplied! "(see Fig. 8]^

▼ Place a gasket with a filter between the tap and the hose (included)

to the machine) and tighten tightly by hand (Fig. 7-8).

▼ Connect the supply pipe (Fig. 9).

Note Use the new tube supplied with the machine.

▼ During washing, the water supply tap must be fully open

▼ The drain hose must be at a height of 60 cm to 90 cm from the floor

(Fig. 10).

▼ If a stationary drain is provided, a free

hose end; The minimum internal diameter of the drain must be 40 mm.

▼ It is important that the drain hose is not tightly connected to the drain

hole. Thus, air will not accumulate in the siphon, which will prevent water overflow.

▼ If water from the machine must be poured into a sink or sink, hang

the free end of the hose, the bend of which is fixed with a special holder included in the kit, to the edge of the sink and secure the holder

so that it does not fall to the floor (Fig. 11). The sink drain should not be clogged

and the water should drain quickly to avoid overflow.

5M1795

Washing machine ARDO FLZ 105 S reviews

Advantages:

washes well;
rinses well;
economical;
high-quality Italian assembly;
simple and easy to use;
many useful programs;
high-quality and reliable model;
not noisy;
does not vibrate when the legs are adjusted;
large tank, roomy;
electronic intelligent control.

Flaws:

no significant deficiencies were found.

Washing machine ARDO FLZ105S reviews are based on 5 user reviews in Yandex Market.

Operating a washing machine

Page 8

Image
Text

OPERATING THE WASHING MACHINE

USING WASHING POWDER

The washing machine has a container for washing powder and other

detergents with three compartments.

compartment for washing powder for pre-wash or

soaking laundry (1)

compartment for washing powder for main wash (2)

air conditioning compartment (3)

For washing, you should use linseed powder with low flax formation and

air conditioner (if necessary), designed for automatic washing machines. The dosage of these products is indicated on the packaging.

Note Too much powder may cause

the formation of excessive foam and negatively affect
the washing results. Insufficient detergent may result in unsatisfactory washing results.
Note When loading washing powder, it is important that it does not fall

into the conditioner compartment, as
foam will form during rinsing and white spots may remain on items. Conversely , if conditioner gets into the washing powder compartment, the quality of the wash will deteriorate.
Note When using liquid detergent

(recommended for programs without prewash), you should

act

next

way:

take out

partition

from

installation position in the drawer opposite compartment 2 and insert

it into a special groove in the center of the compartment itself.

▼ before you start washing, close the washing powder container

and other detergents.

Attention! Do not remove the detergent container during

while the machine is running, as water may spill out of it.

5M1795

Ardo washing machines

_____________________________________________________________________________________

Models A, SED, TLN, FL, ANNA
Models S1000X, INOX, AE, FLZ, WD, FLSN
Error codes

Ardo TL105S top loading washing machine. When you turn on the wash, it works normally, drains the water, goes into rinse mode, stops and remains in this state, if you manually turn it into rinse mode it doesn’t work either. Most likely the problem is in the pump. SMA TL 105 SX. We start it up as usual, it washes, but the water drainage mode does not turn on, and the unit remains in the same place, the filter is clean. What's happened? Most likely the drain pump is faulty. The Ardo T80X washing machine is in operation (5 kg load). The centrifuge does not turn on and does not spin. What could be the reason? If the SMA does not drain the water, then the spin cycle cannot begin and the drain pump may have failed. If it drains, then the breakdown may be due to wear on the electric motor brushes or wear on the drive belt. SMA model T80, year 2000. It is broken and does not wring out laundry. The washing goes normally, the water drains, but when the centrifuge light comes on, the unit begins to spin the laundry back and forth without picking up much speed. I take out the wet underwear. Tell me, please, what could be the matter? It is necessary to check whether the water drains completely. If yes, then the control board and motor are diagnosed. Washing machine SE 810 (5 kg load). No water supply. In this case, the drum rotates in reverse. The electrovalves are intact (supplied 220 directly and water flows). When blowing in, the water level sensor clicks and the contacts ring. The board is not burnt, nothing suspicious is visible. The fact that the solenoid valve opens at 220 is good; the pressure switch should click at least 3 times when “blowing.” The module will be burnt only in 2/3 of the cases, and in the rest it will look like new. To start checking the module, turn on a program without water, for example, spin, and check. Washing machine Ardo SE 1010, in operation in 2004. When the drum rotates during washing, a knocking sound appears, and it only knocks when the drum is rotated clockwise (one knock per turn). What's the matter? Presumably, the drum drive pulley is loose or, although unlikely, a foreign object has entered the tank. FLS 105, in operation since 2007. It has been in use for 3 years, when spinning and rinsing the belt comes off, you put it back on, turn it on and when the drum rotates faster, it comes off again. Maybe change the belt? Can I do something myself? Check the bearings; they may need to be replaced. Washing machine TL1000EX. When fully loaded, the drum does not rotate. I removed the side cover - for the first 20-30 minutes the engine cannot turn over, then apparently something heats up in the control unit (it feels a little warm to the touch) and the engine turns over as it should. With a minimum load, the defect manifests itself to a lesser extent (I haven’t tried it at idle without laundry). Maybe some relay is overheating and bad contact? The control unit, the starting capacitor, or poor contact in the connectors may be faulty. After three years of inactivity, we connected the Ardo TL1000X machine to the water supply, all the pipes, all the taps, everything is as it should be, but when it is plugged into the network it does not work. The washing program does not start, you cannot hear the water flowing, although it flows through the hose. Moreover, three years ago, when it was connected in another apartment, it worked properly and never broke down. Please tell me why it doesn't work? Question one: how did you check that water flows through the hose? Did you unscrew it and put it in the bath? Is the mesh at the entrance to the machine where you screw the inlet hose clean? Question two: can you hear the fill valve humming? If you can hear it, but the water does not flow, then it is faulty to one degree or another. Question three: Where is your drain hose connected? Into the sewer? Make sure there is no self-draining. The TL105S machine has been running for 1.5 years, it washes as usual, but the water drainage mode does not turn on and the SMA remains in the same place. What could it be? Looks like a blockage. In operation, SMA TL85SX with vertical loading. After the end of the program (including 800 rpm spin), it does not stop working and switches to rinsing mode. The control board has been repaired. Please suggest possible causes of the problem. Most likely, the issue is still a faulty control module. We see no other reasons. Washing machine model TL85S. How to remove a pulley from a motor rotor to replace a bearing? Is it screwed on or is it a press fit? It is pressed in and requires a special puller. Unit T80X, year of manufacture 2005. Malfunction - during the washing mode, the temperature rises above the set one and the unit does not switch to another mode. The temperature sensor or electronic module may be faulty. Malfunction of the Ardo T80X top-loading washing machine. I spun the laundry for 5 hours (in rinse mode), and water leaked onto the floor. I had to stop it manually (turn off the power supply), approximately 1/5 of the water remained in the drum. Restarting the wash did nothing (the unit simply spun the drum occasionally, and did not draw in or drain water). What could be wrong? The pump may be faulty; a clogged drain tract or a malfunction of the level switch cannot be ruled out. SMA TL 800 EX, water does not fill well and takes a long time, little water is collected, the wash cycle is long, the laundry is not washed, the last time I did not draw water at all, the cycle did not start. Perhaps the water pressure is too low. Check the fill, clean the inlet filter. I purchased the TL800EX automatic washing machine in 2001, it worked properly. The machine has never been repaired and, unfortunately, not even cleaned. The other day the water stopped draining. Tell me the probable cause, is repair required and how much will it cost? It's practically just a blockage, or the drain pump has failed. Start simply by cleaning the drain filter. Washing machine Ardo TL 400. In rinse mode with air conditioner, it leaks through the top loading hatch. It is possible that there is an overflow (the level sensor is faulty or clogged), the hatch seal is leaking or torn. Washing machine TL60E. It does not see any program and passes water through itself by gravity. What could be the problem? Try lowering the drain hose into the sink or raising the drain system higher. Washing machine Ardo T80X with vertical loading. It worked fine, without any comments. The next time you turn it on, the “power” light is on, there are no more movements or sounds regardless of the program, the lid is not blocked. There is pressure in the water supply hose, the filter has been cleaned. Where else is worth seeing? The hatch lock or the control unit start button may be faulty. Model T80. Age about 12 years. Used for about 2 years. Then I stood in a dry, warm room. Recently connected, it leaked a little, then stopped. It is quite noisy, the solenoid valve knocked especially loudly when opening. Now the water began to slowly fill in during washing and rinsing. The valve began to knock more quietly. When turned off, if the ball valve is not closed, water slowly flows into the tank, but not critically, about 2 cm above the bottom of the drum. Does it make sense to repair it or do you already need to buy a new washing machine? Check that the drain hose is connected correctly. The drain hose must have a loop 60-80 cm above the floor level. Check the drain for blockages; it is possible that water from the sewer is entering the unit. The fill valve may be faulty. During operation, the Ardo SE 810 washing machine began to rotate poorly. The belt is in order, without the belt the engine works properly, with an empty tank or a small load (duvet cover, sheet) everything seems to work. If you increase the load with at least one more object, the engine cannot rotate the shaft, i.e. the drum shakes and that’s it, the shaft doesn’t rotate any further and only a hum is heard. The drum itself does not jam; the loaded drum rotates manually. What could be the reason? Check the starting system. Washing machine Ardo TL 600 X. In operation for 8 years, the powder remains in the tray and is not washed off. Check the water distribution system in the dispenser. The Ardo TL600X washing machine does not heat the water and does not switch the mode further after pouring water. Problem with water heating. Check the heating element, thermostat and control unit. SMA SE 1010. It rattled in the pump area, the laundry came out wet. A coin was found in the filter. I removed and disassembled the pump. It turned out that the rotor is something like a cylindrical magnet. Where it is inserted, everything was covered with some kind of white coating. I deleted it. After assembly and disassembly, the noise disappeared for a week, but then it began to rattle again. Question: What specific pump malfunctions can occur? Is it lubricated with something or is it filled with water during operation? The pump cannot be repaired, only replaced. Model FLSO 106S. She has such a problem - I can’t start it, the control lamp blinks, and the unit does not respond to anything, although the last wash ended normally, what could be the reason? What do you mean by the indicator light - power indicator? Based on your description, it’s difficult to say anything; it’s not clear whether the hatch is blocked or whether it’s taking in water or not. Washing machine Ardo 780 with vertical loading. The day before, towards the end of the wash, it started knocking. We believed that this was the result of a lump forming. And today, from the very beginning of washing, it worked with a noticeable knock. At the end of the entire washing process, it turned out that the laundry was dry in places and not wrung out. There were also traces of powder and possibly fine sand on it. When spinning an already empty drum, its wobbling is noticeable. Tell us your opinion about what happened and the possibilities of necessary repairs. It should be noted that the unit was in operation for about 15 years. Most likely, the shaft bearings have failed, and over time they will need to be replaced with new ones. Model FLS 80 E. Motor connector is flooded. The module and motor connector need to be replaced. Do you think this happened due to improper operation or is it a factory defect? The reason for the flood is that a low-quality powder or hand-washing powder may have been used, or the level switch may be faulty. Faulty washing machine Ardo FLS105S does not heat the water. And should the glass in the door heat up when washing? When the water heats up, the sunroof glass heats up. If there is no heating, the heating element or temperature sensor may be faulty. Washing machine TL1000X. A ring has fallen into the powder compartment. Can I use the car? Is it possible to get it? A foreign object may block the drain pump; of course, it is recommended to remove it. SMA model TL 1000. When turned on, the drum gains high speed in any mode. Electronic module for the electric motor circuit. Motor tachometer. SMA with vertical loading T80X. When spinning, it overflows too much water. What could be the problem? There may be a problem with the water drainage. The device does not drain water. Washing machine T80X. Recently, in spin mode, it began to rumble, and as a result, the filler pipe vomited. What is the problem? In operation for 9 years. Most likely, the problem is with wear of the bearing, drum seal, and shock absorbers. We have a T80X machine. Vertical loading. In work for 2.5 years. We turn on the program - everything works. Let's say it's washed, but the programmer itself doesn't even move. That is, it can wash for 2-3 hours until you turn it off and start rinsing manually. What could this be? How to fix? Check the heating element, it may be faulty. Stir. machine FLS 80 E with a load of 5 kg. Doesn't wring out. After the washing cycle according to any selected program (temperature/fabric), with an indication of 12 to 1 minutes (Spin mode), the drum rotates at standard rinse speeds, periodically stopping and draining the water. By separately selecting the “Spin” program, the entire cycle described above from 12 to 1 minute is repeated without spinning. When testing over the entire rpm range (500-1000), it turned out that the device is capable of “freezing” at 12 minutes, carrying out a cycle of rotations and drains, then suddenly giving out a time of 1 minute and turning off without pressing. And in some cases, a malfunction in the spin program is noticed: reaching 10-9 minutes, a click occurs and the number 12 flashes on the display again. Similar failures follow each other and the cycle “10 click 12” stretches for 30-40 minutes, then the indication pops up as standard 1 minute and the unit stops. Due to the absence of other violations in functions and modes, I think about the control module. In addition to a breakdown of the control module, the carbon brushes of the electric motor may be worn out. The shaft speed sensor may be broken. Machine TL 600 X. The drum inside is displaced and it is impossible to get the laundry out. Most likely, the drum opened while the unit was operating. Now, to open it, you need to disassemble the SMA and the side panels to unlock the hatch. The TL600X washing machine does not spin. Everything works, at the moment of spin there is a click, and the speed does not pick up, the rotation is the same. Help determine the malfunction, what to look at in order, it’s a pity that there are no diagrams and the parameters are unknown. The starting capacitor or motor appears to be faulty. Washing machine TL105L (vertical loading up to 5 kg). The unit does not spin in any mode. In this case, the time on the display is reset to 1 minute, and then the machine turns off. If the SMA does not squeeze out, then check the water heater, electric motor brushes and drain pump. Vertical washing machine Ardo TL 105 SX. The programs are set (indicators are on), when you press the start button, nothing happens. The hatch is not blocked, the program does not start. Replaced the UBL with a new one. Everything is the same. WHEN you close the two UBL supply wires directly, everything works. What could it be? Or is the new Ubl also faulty? If, when you press the “START” button, the hatch does not lock and the program does not start, then the problem may be not only in the UBL (hatch locking device), but also in the failure of the button, in the failure of the control module and in the failure of the interference filter. Vertical machine T80X. It washes endlessly and does not go into rinse and spin mode. The heating element is working - the water in the tank is warm. The level and temperature sensors may have failed. The device waits for a signal from the sensors and switches to the next mode. Washing machine T80X. The program selection knob stopped turning during operation. It performs one operation indefinitely. Changing the control module did not help. Tell me, what is the problem? Failure of the heating element, pump, KSMA and normal self-draining is possible. The Ardo TL 800 EX Easy Logik washing machine has stopped draining water, the wash cycle completes, but there remains a full drum of hot water, what could this be and how to fix it yourself, we do not have services. Check the drain path for blockages, and most likely the pump, check it under load, it will hum and there will be no drainage, change it. The TL800EX machine does not start washing, and the top cover does not lock. Check the hatch lock. This problem occurred with the SE 1010 machine. During washing, the drum does not spin, but during spinning and rinsing, the drum spins, and besides, the drum itself generates an electric current. Based on your description that the drum does not spin during washing, but spins and generates electricity during spinning and rinsing, we can conclude that the heating element (heating element) is faulty. During the washing program, the unit checks the operation of the heating element, and, detecting a malfunction, does not give a signal to start washing. If the washing started, the heating element would “short” and knock out the plugs in the apartment. In the rinse and spin mode, the heating element is not tested and the drum rotates. It is necessary to check it for a short circuit and, if found, replace it. Then the SMA will begin to work normally. Model SE 810 has bugs. It may freeze and perform a spin or other operation for several cycles. Can this be fixed? It is quite possible to fix this. Most likely, the program control module has failed. Washing machine Ardo TL1000EX. The drive belt broke, what caused this? There may be a problem with the drum bearing (jamming). How to remove or clean the dispenser hopper on the SMA TL600X? The cuvette (powder dispenser) is located on the lid of the washer and is removed by snapping off 4 plastic fasteners at the corners of the lid. Machine TL810E. After the wash cycle and draining the water, it does not want to go through the spin cycle. It loops on drain-scroll-drain and so on constantly. The water level sensor is fine, the heating element is intact, the tachometer works, the brushes are about a centimeter and a half long. What else could it be? Brushes 1.5 cm are not enough, because... brushes less than 2 cm are already considered worn out. However, we recommend checking the drain pump for serviceability. In the Ardo TL80E washing machine (5 kg load), a knock appeared inside the drum; during disassembly, a defect was discovered. Is it possible that a broken striker is causing the knocking noise? There are no foreign things inside. The knocking noise only occurs when running at high speeds. Of course, the knocking noise may be due to a faulty striker. There is now no balance in the drum, and knocking occurs. There could also be a fault in the bearing. But in any case, the drum striker must first be corrected. Model FLS 105 S, 2.5 years old, has not rinsed, spun or drained water for the last few days. What could it be? Check the drain filter. As soon as I turned on the SMA FLS105S, there was a bang and the light went out, the water just started flowing. Before this, she didn’t spin clothes well; she had to turn on the spin cycle several times. Please tell me what is the reason. In work for almost 3 years. It looks like the control board is faulty. Washing machine TL80E with vertical loading. The latch hook in the lid broke. Now the lid won't close. Change the hook or handle assembly. SMA TL400 does not drain water; the spin operation is performed with the drum filled with water. If it is a drain filter, how can I clean it if there is water in the drum? Or will the water not flow out if I remove the filter when the drum is full? Try to slowly unscrew the filter and drain the water, but most likely the drain pump is faulty. Washing machine Ardo TL85S. Sometimes it does not drain or does not completely drain the water. The drain filter is clean and the blades rotate easily. Tell me, what could it be? Most likely, the water drain pump will need to be replaced (it sometimes jams). Washing TL810E with vertical loading. Ringed when washing, especially if you put it soaked underwear, and sometimes it will not fasten, and it is normal when spinning is normal. What is the reason? The reason may be overloading SMA, because It is already old and you need to load smaller linen. There should be no causes of breakdowns here, except, as wear of the bearing. Smat Tl80e whistles when draining water and spin. What to do? And yet-she has some kind of lever moves below. What to do with him? To identify the causes of noise during spin, an examination is necessary. Perhaps the whistle comes from the pump, engine and the bearing of the washing node cannot be excluded. With the help of a lever, rollers are advanced for transporting the unit. The model with vertical loading, with spinning, the whole is heated, you open the hot drum and linen as if only boiled hot. What could it be? There may be a malfunction in the water heating system. Maybe the water heater (Ten) began to overheat, and maybe a breakdown in the temperature sensor. It is necessary to check, both the heater and the temperature sensor. Changed Ten a week ago. After that, the machine passed a couple of quick washes. They put on a long washing and when spinning all the water was on the floor. What could have happened? Perhaps, when installing a new heating element, it was loosely installed in a tank or a screw that presses it to Baku was not fully twisted. As a result, there was a leak through the heating attach to Baku. Either the installation of a hee and you have an unrelated event. ARDO TL85SX washing machine. There is no drain of water and squeezing, the pump was checked - it works. What to do next? The machine erases, heats the water. Presumably, did you check the pump by removing the unit and including it in the outlet? If so, then it is probably necessary to change it. You can check by launching the wash, wait for the smell to get up, check whether the power is supplied to the pump, or to listen to whether there is a rumble from it, if there are one of these requirements, replace the pump. Model TL80E. The door does not open even after the power is turned off. What can be done? It is required to replace UBB (hatch lock device). To turn on the washer, you need to hit the door several times, and only then the door is blocked. If it helps only blows to the hatch, then check if the hatch itself is sagging. Maybe he is incorrectly enters into the grooves of UBB (Luke lock device). If the hatch is not sagged, then, most likely, the malfunction in the UBB itself and it is necessary to replace it with a working one. After washing, the hatch does not open. We waited more than 30 minutes. After washing - nothing. They launched a new washing program - it still does not open. Most likely, when washing, the drum hatch was opened. In order to open the hatch now, you need to partially disassemble the unit. The 2004 ARDO TL800EX washing machine. When choosing any program, it picks up water, waits a little and then drains (without squeezing). What could be the reason? I checked the pump for the drain, the heating is in order. Perhaps malfunctioning level relay or control unit. Washing machine Ardo FLS 105 L (loading 5 kg). On an annex, instead of 10 minutes, stops 2 minutes. In other programs, it also does not end in washing (does not write end). In your case, the secondary winding of the electric motor or wear of the engine brushes may fail. FLS105S machine. Washing modes do not switch, just stands in the last mode, and water boils. We tried to throw back the heater and achieve. I reached, leaked water and stood again in the same mode. Check the temperature sensor. Ardo 1000 washing machine does not squeeze at all, but is erasing. What can break? Probably, the electric motor was out of order. The washing machine T60, the water set and immediately at the same time drain. What happens and how to repair? Lingerie in the drum is dry. Presumably malfunctioning level relay or control module. Suba T60. When working, the rattle and clicking noise when rotating the drum in one direction, when rotating into the other, everything is fine. How to disassemble the unit to get an object from which it knocks. In all likelihood, in the tank an extraneous object that you can try to extract through the seat of the heating element. Water flows through the door during rinsing. What is the reason and how to get rid? Most likely, the reason is in the tank door. Check if something comes there.

_________________________________________________________________________________

_____________________________________________________________________________________

Operation of the LG SMA I bought an LG E10B8ND DD washing machine and have only washed it 3 times so far. The problem is this. It washes very quietly, since the all-wheel drive goes directly to the drum. Even spinning at 1000 rpm is quiet, but when it drains...

Samsung WF 8590,6450,6520 We repair the Samsung WF8590NMW8 diamond washing machine (5 kg load). The DE error appears on the display, although 220 is supplied to the lock itself (checked). The most interesting thing is that I decided to test the lock on another SMA, and it worked. Has anyone encountered...

Ariston RSM, WMSF, AVTL Washing machine Ariston avtl 104, with vertical loading 5 kg. The situation is very unclear. SMA can wash off normally, but recently it has started to behave strangely. When rinsing, it stops and the indicator on the power button goes out...

Indesit IWSB, WS, WIU, WIN Machine iwsb 5085, description of the problem. She pours water, the drum rotates for a couple of seconds in one direction, stops, then 2 more times, a couple of seconds each, in the opposite direction and silence. The indicators light up as expected, programs switch, but...

______________________________________________________________________________________

FAULTS AND REPAIRS OPERATION AND SERVICE ERROR CODES

______________________________________________________________________________________

Repair of Bosch Maxx 5 automatic washing machine. Bosch maxx 5 speed edition WLX 20463 OE washing machine in operation. I began to perform the washing program incorrectly. We set the hand wash program, the spin was completely turned off. After washing, SMA switched to rinsing...

Candy Aqua, GVS4, GS3, CS2 There is a smell in the gvs4 126dw3 washing machine. I wash with the addition of liquid Calgon, but there is no effect. Sometimes I rinse my laundry with vinegar. If the linen is thin, like bed linen, then it does not smell. But the towels started to smell. What to do?

Electrolux EWW, EW, EWX The Electrolux EWW 1686 washing machine is in operation. It started tapping when washing, regardless of whether it was spinning, stopping before changing modes, or washing. It knocks periodically, not all the time. The sound comes approximately from the control module...

Zanussi ZWY, ZWSE, ZWT Washing machine zwy 51004 wa, bought about a month ago. I set the washing program, the final spin occurs, and the machine starts washing again, and so on ad infinitum, until you just turn on the water draining program. What could be the problem?

Repair of Ardo SED, TLN, FL Ardo TLN 126. It has a display, and when you turn on the washing program, the washing time is displayed. Gradually it should decrease, but here it is. I turn on the 20-minute wash, but in the end it takes 40 minutes or even more to wash, and the time is constant...

Beko WKB, WN, WKE, WM Model WM 3350 E. We started working in the “short wash” mode, the program worked completely (the door unlock button lit up), but water remained inside. In fact, rinsing and spinning did not work. When I tried to reboot, nothing changed, the sensors...

Repair of ACS Gorenje WS,WT Model WS 43100. The fill valve does not open. Writes "Error 9". This is an error related to aquastop. There is no aquastop. I bought a new non-original valve, took the coils from the old one, put it on with difficulty, one might say, hammered it in. I installed it, did a couple of washes...

Whirlpool AWE, WTLS, AWOC We bought a Whirlpool AWE 6516 washing machine with top loading and electronic control. Container for detergents under the lid. I pour the conditioner into the container, and it immediately pours out of the small...

Care, Cleaning the washing machine, How to remove the detergent compartment

Cleaning the filter

Image
Text

[\l

CARE

CLEANING THE WASHING MACHINE

The washing machine is designed to minimize the need for maintenance operations. However, one should not forget Clean the machine regularly.

Before cleaning the machine, make sure it is disconnected

from the electrical outlet and that the water supply valve is closed.

For cleaning the outer casing and plastic parts of the washing machine

Only use a soft, damp cloth.

ATTENTION!! Never use it to clean the machine.

chemicals, abrasives,

alcohol, soap, gasoline and other solvents,
as they can damage it (Fig. 21).
After finishing washing, leave the machine door open for a while,

to allow its rubber parts to dry.

You should periodically wash the container for washing powder and detergents.

funds. To do this, remove the container for washing powder and rinse it under running water (Fig. 22). Insert the container back.

How to remove the detergent compartment

▼ open the detergent compartment;

▼ with your right hand, press the “PUSH” inscription and remove the compartment by pulling

it on yourself (Fig. 23)

CLEANING THE FILTER

ATTENTION!! Before you begin to carry out the described

below operations, check that
the water has been drained from the washing machine. Do not remove the filter while the machine is running or when the machine is filled with water.
To collect the water remaining in the filter, place a rag under it or place a flat bowl. Open the filter cover, unscrew it counterclockwise and remove it (Fig. 24-25).

The filter must be cleaned periodically.

Rinse the filter under running water and remove all foreign particles from it. Insert and screw the filter clockwise and then check it

tightness.

SM1795