BEKO washing machine malfunctions: repair tips

Most washing machine users noted the reliability of their home units, which were manufactured 10-15 years ago.
But even those machines with their good quality of parts and assembly do not have an infinite service life, and sometimes these machines still break down. Repairing a washing machine from VEKO, Indesit, Ariston and other devices from other manufacturing companies is no longer always worth it and you need to buy a new washing device. But sometimes the problem is not as serious as we could imagine, and it can be fixed with your own hands, thanks to which you can extend the life of your beloved assistant. For this reason, today we will look at typical breakdowns and action algorithms for home repair of BEKO washing machines.

Washing machine BEKO WMN 6506 D – instructions for use

You can download the operating manual for the BEKO WMN 6506 D in Russian for free from the link below or view the instructions in your browser.

How to troubleshoot Beko WMN washing machines

_____________________________________________________________________________

_____________________________________________________________________________

• All SMA Beko models

At home I use SMA Beko WMN 6356 SD. This morning I noticed that there was a water leak. Water may flow out from the bottom or from the hatch door during washing or rinsing. What to do? The hatch seal is probably leaking. You should install a new one. Model 6350 SE (4 kg load). When the electric motor is turned on, there is a sort of electric click, the machine starts to work, then everything is fine during operation. When clicked, the load is on the light, but the 16A machine does not knock out. Sparks and stress are absolutely normal, the only thing worth checking is the wear of the motor brushes. If the coals are less than 2 cm, we recommend replacing them. Need help troubleshooting a 6356 SD machine. Here is the problem itself: the automatic plug began to knock out at the moment the rinse or wash modes started. Can anyone tell me what the reason is? Often the cause of the malfunction can be found in the heating element. Replace this item. Washing machine Beko WMN 6358 SE. Doesn't rinse clothes well; white flakes remain after spinning. And lately he hasn’t been wringing out his laundry. The water is only pumped out, but there is no spin. Poor rinsing of laundry, as a rule, is due to a malfunction of the heating element, that is, cold water cannot dissolve the powder and, accordingly, it is not rinsed. And the second defect indicates a faulty heating element. Six months ago, a washing machine was put into operation. It worked fine. On Monday, my wife decided to wash her clothes, but the equipment could not turn on. The screen does not light up. Why did this happen? Presumably, the electronics control module, which provides the command to start the equipment, is inoperative. How to hang a door on SMA 6508 K? To rehash the hatch, you need to remove the front panel. To do this, you need to remove the top cover and the module (you will also have to remove the hatch cuff). After this, swap the UBL (hatch locking device) and the hatch fastening loop. Washing machine 6510 N. When spinning, an unimaginable shaking of the tank begins and the rubber cuff of the tank starts flapping. At the very beginning of operation in October 2002, the same thing happened. They called a technician from the warranty workshop, who sorted everything out in a few minutes; he said the reason was that the counterweights were loose. I took off the cover, checked the tightness of the bolts from above, tilted the car, checked the tightness from below, everything was tight. Once I turned it on, everything was fine (two terry towels). I loaded it with laundry and there was also some twitching and flapping during the spin cycle. What is the problem? Increased vibration can be caused by a number of reasons: first of all, it is necessary to check the fastenings of balancing devices (counterweights) and their integrity; then the performance of the shock absorbers and the absence of play in the washing unit. If this malfunction occurs periodically, it may be due to poor placement of the laundry. Help me how to fix a broken washing machine. The device constantly draws and drains water. Tell me, what is the problem? We can assume that the device that analyzes the water level in the tank of the machine may have failed. A new one needs to be installed. I have a question of the following nature: the Beko WMN 6350 SE washing machine has not been used for a long time (5 years), now problems appear when I try to use it. It takes a very long time to collect water, and very little of it enters the drum. The impression is that water is being collected, but little or no water is flowing into the drum. The connection to the water supply is correct. The powder from the compartment is also not rinsed out. What could be the cause of the malfunction? The fact is that water enters the unit under pressure in the water supply system. During washing, the triac (programmer) commands the electronic water supply valve to open, and water under pressure from the water supply enters the machine. Over a long period of inactivity (5 years), the valve solenoids could have dried out and it stopped opening the damper. If the water does not even wash away the powder, and you do not see a puddle of water under the SMA, then this may indicate a malfunction of the supply valve. It needs to be replaced with a new one. Veko 6506 does not heat water. Why doesn't it heat up the water? The heating element works normally, everything seems to be normal, but the water in the drum is cold. What to do? What is the reason? If the heating element heats, but the water is cold, then most likely there is a water leak into the sewer and the unit periodically adds cold water to the tank. Place the drain hose in the tub and start the wash. Machine 6358 SE. When turned on, water is drawn in and then washing should begin, i.e. The reel is spinning, but the clock is ticking and there is no rotation. Then it drains, then fills up the water again, and so on until the wash is finished. Why doesn't the drum rotate? Is this a serious breakdown? In your case, a number of malfunctions are possible: 1. The water pressure switch (pressure switch) is faulty. This part controls the water level in the unit. Perhaps it “seems” to him that the water has been overfilled and the motor turns on to drain the water (without turning on the drum). 2. The electric motor brushes are faulty - as a result, the drum does not rotate. 3. The control mechanism (board or programmer) is faulty. The command to start washing is not received. In all these cases, the symptoms you described are possible. The Beko WMN 6510 N washing machine is in operation. When you turn it on, you hear it for 2-3 seconds. a slight noise from the programmer and it freezes. In 2005 there was a repair - replacement of the programmer. Please tell me what the problem is and can I fix it myself? In all likelihood, the programmer is faulty and needs to be replaced. Can you tell me the number and dimensions of the bearings for the washing machine 6358 SE? Oil seal marking: 30x55x10. The bearing brand is 6205 ZZ and its dimensions are 25x52x15. I removed the panel in the Veko 6508 machine. How to set the indicator and wash program switch correctly? It is impossible to install the knobs (program selectors) incorrectly, because... they have a slot that can only fit into the control module plug in a single way. Washing machine Beko WMN 6506 D manufactured in 2000. The drum spins constantly and does not fill or drain water. Maybe you have a circuit diagram of the control module for further study of this model? What kind of semiconductor element BTB16 is, how can it be checked for suitability for further use? According to the technical documentation, electronic modules must be replaced, they cannot be repaired. The washing machine operated for 2 years without any complaints. And then yesterday I saw that she couldn’t drain the water. The programs are fine, the device just makes a hum. What's wrong? The main factor is damage to the drain pump. SMA Beko 6510 does not heat water, please tell me the location of the heating element. Is it possible to get it from above? The heating element is located at the bottom of the tank. Washing machine WMN 6508 K (5 kg load) does not switch the operating mode from washing to rinsing, etc. What to see? Check whether the unit drains water after the main wash. If not, then the drain pump may have failed, and without drained water from the wash, rinsing simply cannot begin. There was a breakdown at the SMA. It cannot fill with water and the wash cycle does not complete. What is the problem and how can I fix it? Apparently, the valve supplying water to the unit was broken. It needs to be replaced with a good one. The last time it was turned on, the SMA did not start the program, the filling of water into the tank did not start, the control panel shows an equipment malfunction. The machine carried out its last wash without failures, with high quality, and before this there had never been any malfunctions. You need to test the solenoid valve on the water inlet, it may be faulty. The valve needs to be replaced, and the mesh filter at the water inlet must be additionally cleaned mechanically and chemically. When you start the Beko automatic machine, the programs that are selected by the user do not start. The washing mode is constantly changing, so it is impossible to select the optimal program for the type of laundry. The equipment does not indicate a malfunction of the indicator panel; it works until the end of the program. Most likely, there was a problem with the control module on the board, where there may be burnt-out elements. Drain problem. I checked the hoses and washed them. The pump is spinning. All is clear. I look at the ball. When draining the water, it probably goes down and blocks the hole in the hose. How to get rid of this? Maybe there should be some kind of ball movement limiter? Maybe it (the limiter) broke off? And this is how the ball blocks the outlet of water? Tell me, please, what to do about this? The ball that prevents self-draining should be in the drain hose and rise to the top when the drain pump starts operating. For several days in a row, SMA did not finish washing correctly, and on any of the running programs. When draining water after the main stage, a failure constantly occurs and the equipment has to be restarted. The equipment does not function correctly, the washing is carried out incorrectly. There may be a problem with the operation of the pressure switch, which needs to be changed. The start-pause button flashes, the valve operation cannot be heard. When the water was turned off, it hummed, but now clicks are heard in the door area and in the instrument panel. It is necessary to check the hatch locking device. Everything is wired and connected, I don’t know whether it’s correct or not, but the indicator lights up. There is no water filling process. What could be spoiled? After purchase it was turned on for the first time. Question number two: are such problems corrected at the service or is it possible to fix them at home? The water pressure may be too low. Check the fill, clean the inlet filter. Open the fill valve. The drum of the Veko washing machine does not work. You can select a wash, any program starts normally. Water is poured in, then the water is heated in the tank to the parameters set by the mode, after which, instead of starting the drum into operation, it is blocked, showing a malfunction on the display panel. The sound of the electric motor running is not heard. The device does not function separately either during rinsing or spinning, with the same fault indications on the panel. It appears that the electric motor is faulty. For several washes in a row, the machine does not finish washing; the drum rotates until it is unplugged. After switching on again, you must set rinse and spin separately, then the wash is completed. This causes great inconvenience in use. Most likely, the control board is faulty, or the triac may have burned out. Beko washing machine in operation. When turned on, it begins to draw water and the pump does not turn off. Most likely an electronic malfunction. The SMA is gaining water and that’s it. It sits for about 10 minutes, then the program end light turns on and drains the water. The reason for the breakdown? After filling the water, according to the program, the unit should start heating the water. Most likely, the heating element has failed, and to avoid a short circuit in the wiring, water is drained. The machine stopped pumping out water and spinning. Can it be repaired and what’s wrong with it? Until the unit drains the water, the program will not proceed to the spin procedure. It is necessary to check whether the drain filter is clogged; if the filter is clean, then most likely the drain pump has burned out and needs to be replaced with a new one.

_____________________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

Troubleshooting and breakdowns in the Samsung SMA Need advice on how to repair the Samsung WF 7452S9 R washing machine. The following happened: the automatic plug breaks when starting the rinse or wash program modes. Read more

How to troubleshoot problems with Beko WMN washing machines. Washing machine WMN 6510 N. When spinning, the tank begins to shake violently and the rubber cuff of the tank begins to slam. At the very beginning of operation in October 2002, the same thing happened. Called the master Read more

Problems with Bosch WLG washing machines - Repair recommendations When the WLG20265OE washing machine operates in any mode (spin, rinse, wash) when setting any speed (100-1000), the machine reaches maximum speed Read more

Questions about operation, malfunctions and service of the AEG SMA I have an AEG AMS 7500i (narrow) machine. When washing, a squeaking (grinding) sound occurs, similar to the squeak of rubber. What could this be and could it cause it to break? What you need Read more

Tips for troubleshooting SMA Ardo SMA SE 1010. It rattled in the pump area, the laundry came out wet. A coin was found in the filter. I removed and disassembled the pump. It turned out that the rotor is something like Read more

Questions about the operation and breakdowns of the Siemens ACS In operation WM10N040OE. When water is drawn into the drum, when turned on, water immediately begins to flow from below. I checked the hoses - they are intact, but they are leaking from all sides. Please tell me what the problem is and how Read more

Problems, adjustments and settings of Whirlpool AWG washing machines Model AWG 223. Was washed for 2 years without problems. Now I have stopped spinning in the rinse-spin mode, just spin. Haven't tested it in other modes. The drain pump is heard, the drum is spinning, but Read more

Recommendations for troubleshooting in SMA Atlant The Atlant 50C81 washing machine is in operation. Instead of rinsing, I accidentally turned on the express wash and, already during the cycle, tried to switch to rinsing without stopping the unit Read more

How to call a specialist

You can submit a request for repairs every day from 8.00 to 22.00 by phone:

or you can fill out the online form on the website at any time. In your message please indicate:

On the day of repair, the technician will call you to confirm his arrival time.

If your BEKO WMN 6506 K washing machine breaks down, contact RemBytTech! Our technician will come to you within 24 hours of contacting you and will repair your washing machine right in your home with high quality and with a guarantee of up to 2 years.

Source

Characteristics:

General characteristics

Typical causes of eyelid failures and their individual solutions

As we have already noted above, malfunctions of washing units can easily reveal this through their external symptoms with incorrect operation or complete failure. But how can these breakdowns be correctly associated with certain breakdowns? Here you will already need some knowledge and advice from leading experts, which we will be happy to present in this article.

If you notice that washing is done in cold water instead of the set 40

or 60 degrees - this indicates a breakdown of the water heating element (heating element) , or the control board .

You can come to this conclusion if you set the washing temperature to 30 degrees Celsius, and the machine persistently brings it to a boil, thereby mercilessly spoiling your items made of delicate fabrics. In this case, it is more likely that the board is faulty than the heating element, but just in case, check both.

When you start a program, the machine should begin to fill its tank with water. All this will happen with varying intensity, which directly depends on the washing mode you choose. To take a look at the process of filling water, look through the tank window. But if you notice that after twenty or thirty minutes the machine may freeze and stop the execution of the program, displaying some kind of error code. four different reasons for this development of events

• The lack of water in the water supply system is easy to check if you simply go into the bathroom and try to open the tap.
• Clogged water filter, which is located at the base of the inlet hose (if you have one, of course).
• Fill valve failure.
• Control unit element malfunction.

VEKO washing machines are designed in such a way that they will not start running any program until you close the hatch completely and the sensor in the machine detects a signal that the machine is ready.

If a problem arises with the hatch locking device, you need to carefully press down the hatch with your knee and turn on the desired washing program again, because there is a possibility that the locking hook simply does not reach the end of the desired part and the fixation does not have time to occur.

After the washing program is completed, the washing device should itself begin to rinse off the soapy water and pour in fresh water for rinsing. This process is usually accompanied by the hum of the drain pump.

The draining takes place quite quickly, after which the machine again begins to draw clean and fresh water. If the machine just can’t drain the water, and then just stops and freezes, or

and she tries to drain the water, the pump starts to hum louder, but the draining still doesn’t start, then the problem is the following:

1. At the pump.
2. There is a blockage in the sewer or drain hose.
3. On the management board.

If the machine is very noisy, and the drum rotates with a terrible grinding, clanging and knocking noise, then perhaps the bearings in the VEKO washing machine have broken or a standard body of foreign origin made of metal has gotten into the tank, stuck between the walls and the wall has begun to jam. This type of breakdown must be corrected immediately by first turning off the machine.

The machine may also not turn on completely or the indicator lights will begin to “blink” , and if this happens over and over again, and rebooting does not help, then this is a sign that at the moment it may:

• The on/off button of your washing device is broken.
• The power supply breaks down.
• The network cable is broken.

It will be best if the VEKO washing machine with a display does not freeze, but simply gives an error with a code that will make it much easier to determine the cause of the breakdown without seeking help from a specialist. All this can be viewed in a special table.

Is it possible to fix everything with your own hands?

In theory, all VEKO automatic machines can be repaired, no matter what their load is or whether they have a control panel.

But in practice, other problems may arise that you are unlikely to be able to deal with, or repairs will be too expensive, or the necessary spare parts are not available. In any case, if we have already discovered a breakdown and want to fix it ourselves, we shouldn’t take into account all the factors, which is why he later realizes that he just lost money and time. As they say, “the miser pays twice.”

If a washing machine bearing is being replaced, it may take an experienced technician several hours, so we advise you to time it and compare how long it took the technician to do the job and how much it would take you.

Experts tirelessly recommend doing only minor repairs, which involve replacing elements or removing blockages. The rest should be left for the experienced hands of the master, because if you spoil something yourself, it will cost you even more. In workshops, after repairs they give a small guarantee. So, what can you fix in a VEKO machine with your own hands?

• 
  Clean the drain filter, removing dirt, debris and other things that cause inconvenience in the operation of the machine.

• Replace the drain pump, but only when you are absolutely sure that the old pump has completely failed.
• Replace the inlet valve. To get started with this, first make sure that the problem is not with the board at all.
• Replace the heating element.

In VEKO washing machines, heating elements often deteriorate, especially if they are domestic models with a load of six kilograms. It’s not at all difficult to make the replacement yourself, because the main thing is that all actions are carried out according to the recommendations of specialists.

1. 
   The heating element in VEKO machines is located in the back of the tank, so first remove the back panel, after unscrewing several bolts.

2. After removing the wall, we will see a pulley (a decent-sized round wheel), just below which the heating element is located.
3. We take out the required key and unscrew the fastener, disconnecting the wires from the contacts.
4. We apply force, but still carefully pull the heating element out of the groove.
5. We buy the same part as a replacement.
6. We insert the heating element and do not forget to screw it.
7. We reconnect the wires, reattach the back wall and check the result of our painstaking work.

As a result, I would like to say that VEKO washing machines are generally very reliable, but, like all appliances, they also sometimes break down

.

Inviting a specialist can often be expensive, so do this only in cases where nothing worked out for you yourself or the breakdown is very serious. In all other cases, you can save money and fix everything yourself.

BEKO WMN 6506 D Reviews:

You may also be interested in:

Shops in Moscow

Type: Pickup point: PickPoint: Izmailovsky-2: daily Address: Moscow, Izmailovsky b., 43, office 220

Type: Pick-up point: PickPoint: Balaklava: daily Address: Moscow, Balaklava prospekt, 5

Type: Pick-up point: BC Nagatinsky: daily Address: Moscow, Varshavskoe highway, 39, office 421

Type: Pick-up point: PickPoint: Ukhtomskogo Opolcheniya: daily Address: Moscow, Ukhtomskogo Opolcheniya st., 1

Type: Pick-up point: StroyTsentr Lefortovo: daily Address: Moscow, 2nd Kabelny proezd, 1, office 4