Sometimes situations arise when we urgently need operating instructions for a washing machine, but it takes a very long time to search for it and it is not a fact that it will lead to a positive result. It’s easier to go to the Internet, make an appropriate request and receive a detailed answer. At the same time, real photographs and explanations are often attached on the Internet. Sometimes you can stumble upon nuances about which there is more than a word in the instructions. On this page you can read the instructions for the Siemens IQ300 washing machine.
Typical faults
Let's look at the breakdowns that most often occur, as well as the possibilities of repairing Siemens washing machines with your own hands.
Drain tract clogged, pump malfunction in a Siemens machine
Poor drainage of water after washing or its complete absence indicates a blockage in the drain pipe or filter, or a breakdown of the pump - in 30% of cases.
The pump in a Siemens washing machine is located behind the front panel. Therefore, to get to it, you will have to work hard:
Check the pipe and pump for blockages. To clean, simply remove the pipe and rinse under running water.
To remove the pump, disconnect the connectors and unscrew the fixing bolts.
Problems with the Siemens CM inlet valve
If you notice that the washer does not fill or overflows water, the intake valve is probably broken. You can repair and replace the valve in a Siemens washing machine yourself:
You can install the new element in reverse order.
No water heating, heating element failure in Siemens car
Heating element malfunctions account for 15% of all Siemens machine breakdowns. The reason for this is scale or short circuit. Scale prevents the heater from releasing heat, causing it to overheat and burn out.
Having reached the heating element in the Siemens washing machine, check it with a multimeter before replacing it.
To remove the heating element, remove the front panel of the SM, as described above. Attach the multimeter probes to its contacts and compare the readings with the photo.
If there is a malfunction, replace it yourself:
Water leak in Siemens machine
Water leakage problems account for 10% of all breakdowns.
Leakage occurs due to depressurization of seams or damage to parts and connections. The hatch cuff may also be damaged or worn.
We'll tell you how to replace the cuff on a Siemens washing machine with your own hands:
Inspect the cuff at the time of damage: can it be repaired or repaired? If not, then a new part is installed.
Worn brushes, motor malfunction
Another 10% of breakdowns are problems with the washing machine motor. At the time of a short circuit, the motor winding could burn out, and the commutator brushes could also wear out.
How to make DIY repairs and replace electric brushes:
After dismantling, inspect the brushes: if they are too worn, it is better to install new elements. Then reinstall the motor on the Siemens washing machine.
It happens that electronic components fail: the electronic board and its components. This is a complex repair that a beginner cannot always do. To understand the issue, you will need a wiring diagram for a Siemens washing machine.
We recommend that if the board breaks down, contact a service center—do-it-yourself repairs in this case are not justified and can only cause harm.
Repair video to help you:
Source
Error E17 - when you can fix it yourself
Code 17 does not always indicate a breakdown. Situations when the SMA is in good order occur quite often. And most problems can be fixed on your own.
| Signs | What is the reason | How to fix |
| Siemens does not fill in water and goes into error F17 or E17. | There is no water in the water supply. Check if there is water by turning on the tap. | Contact the water utility or management company to restore water supply. |
| The water supply to the machine is cut off. Check that the shut-off valve is not closed. | If the valve is closed, turn it to the fully open position. | |
| The inlet hose is squashed or kinked. Perhaps some heavy object fell on it, or one of the household members unsuccessfully moved the hose and bent it. | Inspect the inlet hose. If you find bends, places of compression or twisting, straighten it. | |
| The Siemens machine “murmurs” water for a long time, and then error E 17 is displayed. | Low pressure in the water supply. Check the water pressure by turning on the tap. | To resolve the low pressure problem, contact your water management company. |
| The shut-off valve is not fully open. The shut-off valve may not be fully open. | Turn the valve to the fully open position. | |
| Self-draining of water due to improper installation. Probably, the drain hose is located on the floor - below the level of the tank, which is why the water drains from the SMA by itself. | Check that your Siemens is connected correctly. If you find that the hose is below the tank level, reinstall the washing machine according to the instructions. Or use it to connect washing machines. | |
| The water is gathering very slowly. After which an error code appears. | The input filter is clogged . To protect the MCA from impurities from tap water, a mesh filter is installed on the inlet valve. If it is very clogged, the water will take a long time to fill and the machine will show error E17 or F17. | The filter needs to be cleaned. You can do this yourself according to our instructions or order a filter cleaning service from a specialist. |
If you checked all the specified components, but the error was not resolved, unfortunately, your Siemens is broken.
Siemens IQ300 machine control
The instructions for the Siemens IQ300 washing machine indicate that the first time the machine should run idle, without laundry. In this case, powder should be poured in so that it washes and cleans any debris and dust that may have accumulated there. Then everything is as usual: the laundry is sorted by color and fabric, a certain volume is loaded into the drum and a certain mode is turned on.
Algorithm for starting the Siemens IQ300 washing machine:
- Connecting the machine to the network;
- Opening the cold water tap;
- Select the required program by turning the toggle switch;
- Turning on the SM by pressing the start button;
- If necessary, additional inclusion of some parameters is performed.
In addition to the main mode, you can add a spin function, as well as independently adjust it. The higher the rotation speed of the drum of the Siemens IQ300 washing machine, the stronger the laundry will be wrung out. But be careful when setting the highest rotation speed for all fabrics. Some clothes may become unusable after spinning at 1000 rpm.
Many modern cars have a delayed start function. It allows the user to set the installation startup time to a specific time. This is very convenient if you need to do laundry in the morning rather than at night.
The Siemens IQ300 washing machine is equipped with a wash reduction function, which speeds up all operations several times. If desired, you can use an additional rinse to rid the fabrics of powder.
The instructions indicate that the washing machine has a control panel lock. It allows you to protect small children who constantly strive to turn on and start the car or simply click on different buttons. This can be done by pressing the start key and holding it down.
Siemens SMA fault codes
Before we begin the repair, let's look at the error codes of the Siemens washing machine. Their meanings will tell you where to look for a breakdown.
| Error codes | Meaning |
| F01, F16 | The door is not tightly closed. |
| F02 | Water does not fill up. |
| F03 | No water drainage. |
| F04 | There is a leak. |
| F17 | The water has not reached the minimum level within a certain time. |
| F18 | The timeout has occurred and the water is not draining. |
| F19 | The water did not heat up during the allotted timeout. |
| F20 | There was an unexpected heating of the water. |
| F21 | The engine is not working correctly. The main module has failed. |
| F22 | Thermostat failure. |
| F23 | The Aquastop system has activated. |
| F25 | The turbidity control sensor has failed. |
| F26 | There is a problem with the pressure switch or the additional pressure sensor. |
| F27 | Incorrect setting of the pressure switch or pressure sensor. |
| F28 | The flow sensor is not working. |
| F29 | The flow sensor is clogged. |
| F31 | Water exceeds the norm in the tank.. |
| F34 | The door lock is faulty. |
| F36 | There is a problem with the door locking system. Electronic module malfunction. |
| F37, F38 | Thermostat malfunction. |
| F40 | Problems in the electrical network. The voltage does not correspond to the specified MCA level. |
| F42 | The electric motor or its control triac has failed. |
| F43 | Engine failure. |
| F44 | No rotation in the other direction. |
| F59 | The 3D sensor has failed. |
| F60 | The flow sensor received an incorrect value that does not correspond to the norm. |
| F61 | Door closing data error. |
| F63 | Problems with security functions. |
| F67 | Incorrect coding of the power and main units. |
| E02 | Error in the operation of the electric motor. |
| E67 | Electronic module malfunction. |
How to care for your Siemens IQ300 washing machine
Siemens IQ300 is a modern high-tech installation that is gentle on your laundry. In order to get the desired result, you just need to load the laundry and set the program. The washing machine will do the rest itself. It is highly reliable, so it never attracts attention to itself and does its job perfectly.
But if you don't take care of the "helper", then in the end it will become dirty and smell unpleasant. In addition, all rubber products will become unusable much faster. If you constantly leave sharp things, buttons, coins and other small items in your pockets, the Siemens IQ300 will eventually fail and, at a minimum, leak. And it is very difficult to detect a leak on your own.
In order for Siemens IQ300 washing equipment to please you for a long time, you need to perform the following operations:
- Wash the hatch, drum and powder receptacle with a soap solution in warm water;
- Wipe the hatch, drum and powder receptacle of the Siemens IQ300 machine with a dry cloth so that moisture does not accumulate in them;
- Do not close the hatch and powder receptacle immediately after washing so that they are ventilated.
The washing machine, no matter what it is, requires attention and periodic maintenance. Its durability and reliability depend on this.
