Special error codes, or how a Whirlpool washing machine warns of a malfunction

The advantage of modern Whirlpool washing machines is that they can not only independently detect a breakdown, but tell their owner about it.

Smart technology is equipped with a self-diagnosis system. Once a problem is detected, the corresponding code is displayed on the electronic display.

Read our article about what the error codes in the Whirlpool washing machine mean, how to decipher them and what to do after that.

Some troubleshooting tips

Often Whirlpool washing machine errors appear spontaneously, seemingly for no apparent reason, but many of them, in particular those related to poor drain performance, can be the result of careless handling of the device.
The occurrence of a number of malfunctions can be prevented; to do this, it is worth using a few tips. All models of Whirlpool washing machines have a drain filter. This simple device is designed to protect the drainage path from debris, threads, and scraps of fabric. To ensure that drainage errors occur as rarely as possible, you should regularly remove and clean the filter. The frequency of cleaning is indicated in the instructions for each specific model; in any case, the procedure must be performed at least two to three times a year. Caked detergent can clog the ducts inside the machine, causing the program to stop unexpectedly. It's easy to avoid this. You just need to periodically remove the powder tray and rinse it with running water. It is worth inspecting and, if necessary, cleaning the intake filter at least twice a year. This is a mesh located at the entrance to the car. The frequency of cleaning largely depends on the condition of the plumbing and the quality of water in the system. A dirty mesh can cause water to flow slowly into the drum or stop completely. After each wash, when the laundry has already been removed, you should not immediately close the door; you should leave it ajar so that the “insides” of the machine dry out. Washing with hot water helps clean the inside of the machine. It is useful to sometimes run a wash program at 95 degrees with a small amount of detergent added

This will remove dirt accumulated in the drum and pipes. It is important to monitor the condition of the drain hose. This is one of the weakest points of the car

You can accidentally step on it, place a heavy piece of furniture, or bend it too much. Kinks and blockages are a common cause of faulty drainage. The condition of the inlet hose is equally important. The appearance of kinks and cracks is unacceptable; such a hose must be replaced immediately. To avoid leaks during washing, you need to regularly monitor the condition of the hatch cuff. It must be soft, elastic and always intact. To increase the service life of the cuff, it is recommended to wipe it with a damp cloth after washing.

In order for the machine to serve for a long time and have an attractive appearance, its surface must be periodically cleaned. A damp cloth is suitable for this. If serious contamination occurs, you can use cleaning products, but they should not contain abrasive particles, otherwise the panels may be scratched, which will affect the appearance of the device.

The appearance of errors on the washing machine display is not a reason to panic, it is a signal to the owner, a reminder that the device requires care. If you keep the machine clean, periodically clean it and do not allow water to stagnate inside, errors will rarely occur, and the machine will last a long time.

Let's deal with light bulbs

The LEDs on the control panel of older Whirlpool models are located above the program switch knob. You need to count the light bulbs from left to right. So, the first indicator will be “No water supply”, the second will be “Pre-wash”, the third will be “Wash”, the fourth will be “Rinse”, the fifth will be “Water Hold”, the sixth will be “Drain/Spin”, the seventh will be “Door Open”. As for the lower ones, the eighth is considered the “Clean filter” diode, the ninth is “Service”.

It is through the blinking of some of these nine lights that the technology indicates a failure that has occurred in the system. It is necessary to count which LEDs are lit and figure out what kind of malfunction is indicated by a Whirlpool washing machine without a display.

Reset error

The appearance of an error message is not always a sign of a serious accident. The reason for such a situation could be, for example, a failure caused by a voltage drop. If the error appears for the first time, there is no need to panic; first, you should try to reset the error. A few simple steps will restore the device's functionality or eliminate the possibility of an accidental system failure.

To reset the error you need to do the following:

• disconnect the washing machine from the network (unplug the plug from the socket)
• keep it switched off for at least 15 minutes;
• turn it on again and try to continue washing.

If there was a failure, the machine will continue to work normally, otherwise you will have to study the instructions, figure out what this error means and look for a way to solve the problem.

We will inspect and test the pressure switch

It is easy to provide access to the water level sensor of the Whirlpool washing machine; it is located in the upper part of the unit, directly under the lid. Very rarely the pressure switch is located at the bottom. To get to the part, carefully unscrew the mounting screws and remove the upper wall of the SMA housing, after which the algorithm of actions will be as follows:

• prepare a tube whose diameter will correspond to the diameter of the pressure switch hose;
• disconnect the fitting by carefully loosening the clamp;
• Attach a tube to the pressure hose and blow into it;
• when the pressure switch is working, you will hear 1 or 3 characteristic clicks;
• check the sensor for any damage;
• examine the fitting for blockages;
• When a blockage is detected, flush the hose with a stream of water from the tap.

If after an external examination no defects were identified, you need to check the pressure switch with a multimeter. The device is switched to resistance measurement mode, the tester probes are connected to the sensor contacts. If the values ​​on the screen change, it means that the contacts are actuated and the pressure switch is working. When the resistance value remains fixed, it means that the liquid level sensor has failed.

So, when you have checked the functionality of the main elements that can trigger the F08 error code, no faults have been identified, you should invite a professional to determine the root cause of the code. After all, the problem may come from the main control board, and it is not recommended to deal with it yourself.

Do-it-yourself repair of Whirlpool washing machines

Start by preparing your equipment. This also applies to your safety: unplug the machine and close the water inlet valve. Now you can understand the causes of the problem and decide where to start repairing.

Fixing drainage problems

It is likely that you have encountered the following situation: you loaded the laundry, started the wash, and at the end the machine refused to drain the water. There may be three reasons for this:

1. Clogged drain pipe or filter.
2. The hose or drain is clogged.
3. The pump has failed.

You can check the system for blockages without disassembling the SMA. Start by unscrewing the filter:

• There is a small door under the loading hatch.
• Open it, place the container.
• Unscrew the filter plug counterclockwise.

Remove debris from the filter mesh. Through the opened mounting hole, you can inspect the pump impeller. Sometimes it is blocked by hair, threads that wrap around its axis. Clean the impeller of debris.

Now check the hose. Direct connection to the sewer often leads to blockage. It is much better to connect the drain hose to a siphon. It is easier to clean if necessary.

If the parts are cleaned, but the drainage does not improve, then check the pipe and pump. To do this, you need to lay the washer body on its side.

• Take out the powder dispenser.
• Place an old blanket or towel on the floor.
• Turn the CM body on its side.
• Unclench the pipe clamp. Remove it from its place and clear it of any blockage. You can wash the part with warm water.

Check the pump. If there is a malfunction, replacement is carried out: disconnect the wiring from the pump contacts, unscrew the mounting bolts.

Restoring heating

Your items get rid of dirt well thanks to high temperature and detergent. The powder does not dissolve completely in cold water, so stains do not come off easily. The heating element is responsible for heating in the washing machine. A common cause of breakdowns is scale. To check or replace an element, do this:

• Remove the top cover by unscrewing the screws at the back.
• Remove the bolts around the perimeter of the rear cover. Take it off.
• There is a heating element under the tank.

• Disconnect the wiring and remove the thermistor from the heater housing.
• Check the heater for serviceability (for more information about the diagnostic process, read “How to check the heating element in the SMA”).
• If the element fails, then twist the central nut and push the bolt inward.
• Take out the old heating element, clean its nest from debris and scale.

Install a new heater.

Do-it-yourself engine repair

Noticed the slow rotation of the drum? Do things leave wet and not wrung out? It's time to check the condition of the engine brushes and drive belt.

Let's check the heating element

Often error F08 appears as a result of a heater malfunction. You can check the heating element very quickly. To do this, perform the following algorithm of actions (the sequence of steps described will help owners of machines with a front-loading type; for vertical machines, the manipulations will be slightly different):

• turn off the power to the washing machine;
• disconnect the drain and inlet hoses from the house utilities;
• provide yourself with consolidated access to the rear wall of the washing machine;
• unscrew the bolts holding the back cover;
• Unscrew the bracket covering the heater.

Important! The heating element is located at the bottom of the machine, under a plastic casing; only by removing the protective cover can you gain access to the contacts of the heating element.

Next, disconnect the power contacts, take a multimeter and connect its probes to the terminals of the heating element, set the resistance on the device to 200 Ohms, analyze the results. If the value on the multimeter screen remains approximately the same as it was set, then the heater is fully operational. When the number 1 appears, this indicates a break inside the part and will have to be replaced. When the device displays the number 0 (or a number very close to zero), it means that a short circuit of the heater can be diagnosed, in which case you will also have to install a new heating element.

If the heater passes the first test with a multimeter, just in case, check it for breakdowns. To do this, switch the test device to buzzer mode. You will be notified that the mode has been selected correctly by a lit light and a characteristic signal that will appear when the wires are connected. Connect one multimeter probe to the heating element terminal, and attach the second to the element body. If the device does not make any sounds, everything is fine; if a characteristic squeak is heard, there are breakdowns in the body of the part, and the heater will have to be replaced.

Correcting washing machine errors

The appearance of any of the above errors on the washing machine screen should be a signal to the owner. Even if an error appears and disappears, this does not mean that everything is normal; you need to look for the cause before the problem gets worse. What to do is up to the owner to decide; you can call a mechanic, take the car to a workshop, or take on the work yourself.

Of course, you can disassemble the device yourself only if you have the appropriate knowledge and skills, and the warranty period for the device has expired. Repairing a car is a complicated matter, but it should be noted that doing the work yourself is a good way to save money, because you will only have to pay for the parts that are out of order.

The vast majority of malfunctions can only be eliminated by partially or completely disassembling the device; before starting work, you should carefully study the instructions for the machine and watch a video of disassembling a specific model. It would also be a good idea to arm yourself with a camera or phone with a camera. Photographic recording of each action will significantly facilitate subsequent assembly and will allow you to avoid gross mistakes.

List of the most common breakdowns

Since a modern washing machine is a complex device, it consists of a number of components and assemblies, the list of potential breakdowns is extremely extensive. Among other things, there are a number of specific malfunctions that occur most often:

Another common problem that is typical for both vertical loading machines and traditional front-loaders is the entry of foreign objects into the tank. Despite the apparent insignificance of the incident, in most cases, to solve the problem you will have to almost completely disassemble the washing machine.

Whirlpool washing machine AWE 8730

Evgeniya

, 38 years

I bought a washing machine for my parents, I wasn’t disappointed with the choice – it’s been working for a couple of years now and doesn’t break down. It washes shirts and sheets, you can even wash light shoes (not winter boots). My mother was very pleased with the vertical loading - no need to bend over, which is important for an elderly person. When spinning, it whistles a little, but this is typical for all washers, not just Whirlpool. There is a delayed start, so parents do laundry at night when electricity is cheaper. There are appropriate programs for heavily soiled laundry, and it also rinses out detergent residues from fabrics very well - the “Intensive Rinse” mode is provided for this. My mother and I tried to wash a woolen scarf - no complaints.

Advantages:

• Convenient and intuitive controls are an important plus for older people. To start, just select the program and enable additional options - you can start;
• Automatic stop of the drum in the right place, with the flaps up. The doors themselves open easily and effortlessly;
• Gentle washing of expensive and delicate fabrics.

Flaws:

• The lock on the top door is somehow flimsy and unreliable, it always seems that it is one step away from breaking;
• An irritating whistle during the spin cycle - like a turbine making noise.

Not a bad washing machine for older people.

Possible faults requiring repair

Thanks to our extensive experience in repairing Whirlpool washing machines, we have collected popular breakdowns that lead to error 06.

*Prices are given only for the work of the master. Spare parts are paid extra.

Whirlpool showed code F06 and it’s impossible to wash things? To resolve the problem as quickly as possible, call RemBytTech:

+7 (495) 215 – 14 – 41

+7 (903) 722 – 17 – 03

Or fill out an online application.

The technician will arrive quickly: within 24 hours from the receipt of the application, he will repair your Whirlpool right at home, issue a receipt detailing the work performed, the spare parts used and a warranty period of up to 2 years.

"RemBytTech" - we will quickly help you return your life to normal!

Rate this article: 4.5 1 5 7 votes (average 4.5 based on 7 votes)

Finding the tachometer

In all Whirlpool washing machine models, the tachogenerator is located on the rotating motor shaft. To get to the motor, you need to remove the rear wall of the unit (by unscrewing the fasteners and prying the panel with a screwdriver) and remove the drive belt. First turn off the power to the equipment and disconnect it from the water supply.

Important! Take your time to disassemble the machine, first carefully check the spin mode button - if it is pressed inward, the problem may lie there.

On the engine shaft you will see an iron ring with two wires - this is the tachogenerator or Hall sensor. It cannot be dismantled without removing the engine from the machine. Therefore, if you do not have experience in electrical installation, it is better to entrust the work to a specialist. Otherwise, during experimental repairs, there is a high risk of not correcting, but of aggravating the problem.

Special codes

In addition to the main one, there is an additional list of error codes issued by the Whirlpool technique. It is also presented in the user manual. Let's figure out what malfunctions and malfunctions in the equipment we are talking about.

• FH(F01). Only the first LED is lit. The machine notifies that water does not “enter” the system. There may be several reasons for this: low pressure in the pipes, a closed shut-off valve, a clogged inlet valve, self-draining (if the drain hose is connected incorrectly, the tank fills and then empties). In addition, the problem may lie in a broken level sensor, damaged wiring, or a malfunction of the electronic module. The algorithm of actions for repairing the washing machine will be different in each case.
• FA(F02). Lights 5 and 9 are observed blinking. This means that the “Aquastop” function has been activated. Most often this happens due to a leak. Depressurization of the system is observed when the tank is damaged, the cuff of the hatch door is defective, pipes are broken, etc. Less commonly, the problem is a malfunction of the control module.

• FP (F03). Indicators 5, 6 and 8 light up at the same time. The machine informs about a failure in the drainage system - the liquid is not discharged from the tank into the sewer. Possible causes: pump failure, clogged drain hose or garbage filter, damage to the main control board.
• Fod (F18). Lights 2, 5 and 9 light up. The machine stops working due to excessive foaming. It is possible that the wrong powder is used or the dosage of detergent is greatly exceeded. You need to turn off the device, wait until the “soap” cap disappears and drain the water from the system by starting the appropriate mode.
• FDL. The washing machine indicates that the door lock device is broken. You'll have to inspect the contacts of the blocker. If everything is fine with them, you need to replace the UBL.
• FDU. The hatch is not closed tightly enough. You can try pressing the door with your knee and the lock will work. If it doesn’t help, the UBL needs to be replaced.
• bdd. The code is typical for “verticals”. LEDs 2, 3, 4, 5, 6 and 9 are lit. The unit informs about poorly closed drum flaps. You should proceed as follows: hold down the “Reset” button for 3 seconds. The drum should open. Then lift the washer lid, close the doors again and activate the desired mode.
• F A very rare code found only on modern Whirlpools. Informs that the software has not been updated via the Internet. In this situation, you should contact your provider or service center specialists.

Deciphering errors will help narrow down the range of possible breakdowns. This will make it easier to bring the machine back to “life.” Depending on the complexity of the upcoming repair, you should decide whether to do the work yourself or call a service center.

Interesting:

• Error codes for the Indesit washing machine based on blinking indicator
• Error codes for AEG washing machines
• Kaiser washing machine errors
• Malfunctions of Hotpoint Ariston washing machines
• Error codes for Zanussi washing machines
• Whirlpool dishwasher error codes

Reader comments

Share your opinion - leave a comment

Call the master

There are problems that you cannot cope with on your own. They require specialist help.

For example, you should contact a specialist if the heating element or electronic module breaks down . You can find a specialist by looking at an ad posted on the Internet or in a newspaper.

To avoid meeting with scammers, you need to study the reviews that other clients leave about the selected specialist. It’s good if they are posted on third-party sites.

You need to pay for the work only upon completion of it . You must ask the technician for a receipt and a warranty for the replaced parts. The cost of the work depends on its complexity. Prices start from 1,500 rubles for replacing a pressure switch and end at 6,000-7,000 rubles for repairing a control board.

If the machine is under warranty, you must contact the service center. In this case, the repair will be performed free of charge.

Prevention of the Whirlpool washing machine

In order for any equipment to serve for a long time, it requires proper care. It is much easier and cheaper to determine the nature of the danger in time and take measures to prevent breakdown than to repair an already broken device. In order to understand whether prevention should be carried out, you need to examine the heating element.

The heating element is located under the tank, either in the center or slightly to the side if the loading principle is vertical. You can examine it by first swinging the drum and shining a flashlight through its holes.

Due to calcium and salts contained in the water used, scale accumulates on machine parts. In addition to it, dirt and rust also collect. Only radical measures can help the device work without breakdowns.

Scale can be dealt with in several ways. They are divided into:

• Physical
• Chemical
• Technological

A physical way to combat scale involves the use of filters and converters. They are installed either in the machine hose or in the drainage system.

There are two options:

• Use of mechanical cleaning filters. They have replaceable filters in which rust, dirt and sand settle.
• Magnetic softener - its purpose is to remove magnesium and calcium from water.
  This is achieved with the help of magnets, which make the appearance of calcite impossible by splitting the molecules into ions. This is also useful because, thus, after some time, not a trace of scale will remain on all parts of the machine. Such products are quite expensive, but the service life of washing machines, according to the manufacturer, is extended to 50 years!

It is especially recommended to install softeners when using modern models, such as Whirlpool Awg 237, 263, 6516, 217, 218. The components and parts of these models are quite sensitive to water hardness.

The chemical method consists of putting a special acid-containing product into the machine - it removes scale. In this case, washing occurs, but without loading things. The chemical reaction that occurs when water is heated during the washing process cleans both the tank and the heating element from scale.

Many people know citric acid, sold in grocery stores. So, if you pour it into the powder compartment and turn on the washing mode at a temperature of 90 degrees, then all that remains is to clean the filter, and there will be no trace of scale left.

In order for the machine to work for a long time and without problems, this procedure should be carried out at least once a year. The chemical method of cleaning the machine also has disadvantages. An overdose is dangerous, as the rubber elements of the device may become unusable. And fumes from the use of acid-containing products worsen the air in the apartment.

Old clothes should not be washed in a machine often, because in this case, the water becomes clogged with small particles, which will definitely not be useful.

The following measures can extend the life of the machine:

• Regular filter cleaning
• Installation of water softening units
• Systematic ventilation of the washing drum

If you do not clean the filters, an unpleasant odor will soon appear, which will not be so easy to get rid of. Putrefactive and mold bacteria will appear. Cleaning the filter is not difficult and does not take much time. It can be easily unscrewed and washed in running water.

Water softeners are installed in the water supply system. Also, it is recommended to install a special flask containing salt between the inlet tap and the machine. Special salt is added there once a month, and preferably constantly, from the first days of operation of the device.

A smell in the machine can also appear simply from excess dampness. Therefore, it is recommended to wipe the inside of the machine after each wash. The door should always be slightly open to prevent the cause of the smell - dampness. Additionally, experts advise ventilating the device whenever it is not being washed.

Carrying out a set of preventive measures will help prevent future problems with the machine. You can find many articles on the Internet about ways to clean washing machines.

Recommendations

When carrying out repair and diagnostic activities, the following expert advice can help:

1. The case can only be opened when communications are disconnected.
2. You should not open a washing machine under warranty yourself - you need to contact the service department.
3. Before disassembling, it is advisable to drain the remaining water from the tank.
4. Before you begin disassembling the case, you need to make sure you have the required tools and a multimeter for diagnostics.

Sma whirlpool awe 7515 error f12

Go to: Select a forum CRT TVs LCD TVs and plasma panels Projection TVs TV service menus TFT monitors CRT monitors Desktop computers Laptops and PDAs Peripheral devices DVD players and VCRs Video cameras Cameras Landline and cordless phones Mobile phones and smartphones Washing machines and dishwashers Refrigerators and air conditioners gas and electric stovesMicrowave ovensGas boilersOther household appliances Music centers and amplifiersCar audio systemsPortable audio equipmentDecoding Digital set-top boxes, satellite equipmentMeasuring instrumentsMedical equipmentOther equipment Schematics and service manualsFirmwareDatasheetsShopping arcadesOrder deskFree communicationProgrammersElectronics from A to ZSamodelkin's WorkshopSoftware News, announcements, important topicsCommunication and Information Center Incompetent questionsViolations of the rules

Why does the Whirlpool washing machine malfunction, how can I fix the situation?

F08 almost always indicates the need to repair the equipment of the Whirlpool washing machine. But in rare cases, the problem may be due to a random combination of circumstances and a failure of the control module.

This situation can be resolved by rebooting the equipment. To do this, the Whirlpool washing machine is disconnected from the power supply and turned on again after a quarter of an hour. If the problem does not go away, you need to proceed to sequential equipment diagnostics.

Problem with heating element

The heating element is a heating element that is responsible for heating water in a Whirlpool washing machine.
With prolonged use, it becomes covered with plaque, which is formed from hard water, detergent residues and small debris. A heating element covered with a thick coating cannot provide heating of water to the required temperature and burns out.

In this case, the washing machine may display an error immediately after starting or after the water has been filled and the drum has made several uncertain revolutions.

A heating element that has become unusable cannot be repaired; it is replaced with a new part. To do this, it is necessary to partially disassemble the device.

During the diagnostic process, the heating element must be “ringed” with a multimeter and visually inspected. According to statistics, when F08 appears, a problem with the heating element is the most common situation. In addition to code F08, error F12 may indicate a problem with water heating.

How to check the heating element in a washing machine - on video:

temperature sensor

If the temperature sensor fails, the Whirlpool washing machine cannot correctly determine the degree of water heating. In this case, operation stops and F08 is issued. The solution to the problem is to replace the part.

If inspection of the heating element does not reveal any malfunctions, then you need to check the thermistor. It is located near the contacts of the water heater.

For diagnostics, the part must be removed using the following algorithm:

1. Remove the chip from the heater contacts with the wires.
2. Loosen the nut that secures the heating element.
3. Take out the thermostat.

The thermostat has a cylindrical shape and is made of metal. After it has been removed, you can measure the resistance using a multimeter with probes.

If the thermostat is working, then it is returned to its seat, and the search for a fault in the Whirlpool washing machine continues.

Control block

The control module is a block with radio elements. When they burn out, the control unit is no longer able to control the water heating process, and the operation stops.

To carry out diagnostics, the module is removed from the housing and tested. Faulty Whirlpool elements are replaced, tracks are soldered if necessary. If the module is severely damaged, it may even require complete replacement.

How to perform Whirlpool diagnostics and repairs - on video:

Firmware crash

The Whirlpool control unit has firmware that contains sequences of actions for each built-in program. If the firmware is faulty, the washing machine displays various error codes, including F08.

Such a breakdown usually occurs due to a voltage drop. The solution to the problem is to restore the Whirlpool firmware using a programmer.

Wiring

An open circuit in the water heating circuit in a Whirlpool washing machine or oxidation of the contacts can cause code F08 to appear on the display. The situation can be corrected by examining the wiring in the washing machine.

If a break is detected, the entire cable is twisted or replaced, and the oxidized contacts are cleaned.

Pressostat

A problem with the pressure switch is a rarer situation that leads to the appearance of code F08 on the Whirlpool display.
To analyze the condition, you need to gain access to the part. It is located in the upper part of the case, under the cover.

The pressure switch should be inspected externally and checked with a multimeter. If the resistance value does not change, the sensor has become unusable and will have to be replaced.

FP (F03)

This error code in the Whirlpool AWG 237 washing machine indicates a failure of the water pumping system. In this case, the user sees that water does not leave the tank, even after the work process is completed.

This error may occur due to the following reasons:

• The sump pump has become unusable.
• The drain hose is clogged.
• The control unit has failed.

In models without an interactive display, this error is indicated by flashing lights 4 and 9 on the control panel. What does this code mean? Thus, the machine signals the user about a malfunction of the heater. F04 means insufficient heating of water within the allotted period of time. To eliminate the defect, it is necessary to check the entire electrical system of the device. To solve this problem, it is recommended to contact a specialist.

Washing machine repair

Error F08 in new Whirlpool AWG 237 models, and blinking of LEDs 3 and 9 in units with vertical loading of the previous generation, means failure of the heating element. However, do not rush to replace the heating element. It is necessary to find out the exact cause of the F8 error. Masters claim that if a washing machine issues such a code, it means that the following breakdowns have occurred:

• The wires have oxidized or the wiring has broken.
• The pressure switch has failed.
• There was a temporary failure in the electronic module of the machine.
• The thermistor is faulty.

Washing machine breakdown

Error codes for Whirlpool washing machines with vertical or front loading differ in the way they are signaled. For example, on a model with a display, the F12 combination may appear. And on a device with LEDs, this combination is displayed as blinking lights 3, 4 and 9 on the control panel. What does this error mean? This means that washing occurs in cold water. There is no heating.

To restore the machine's functionality, the following faults must be repaired:

• Inspect and repair the relay.
• Check the serviceability of the heating element.
• Check the wires.
• Inspect the temperature sensor.

Causes of failure and ways to resolve the problem

In very rare cases, a malfunction of a Whirlpool washing machine may be due to an accidental coincidence. In this case, the control board freezes and operation stops.

To reboot, it may be enough to unplug the Whirlpool washing machine for a quarter of an hour, and then turn it on again.

If the problem is one-time, work will be restored. Otherwise, it will be necessary to carry out high-quality diagnostics and identify the exact cause of the failure.

You should also inspect the buttons on the control panel to make sure that none of them (especially Spin) are jammed. If it literally failed, then that could be the problem.

Tachometer

In the case when the Whirlpool washing machine does not start to rotate the drum when starting up and displays F06, then with a high degree of probability this may indicate an error in the operation of the tachometer. To accurately analyze the situation, you need to gain access to the detail. If the tachometer is burned out, it is replaced with a new one.

The tachometer is located in Whirlpool washing machines on the motor shaft. It is accessed from the rear wall.

One of the possible problems is in the video:

Motor brushes

If the motor brushes are worn out, the Whirlpool machine may not be able to gain speed during the spin phase. In advanced situations, rotation may not occur at all. If there is a problem with the brushes, sparking may even occur.

Brushes in an electric motor are consumables. During the operation of the Whirlpool washing machine, they gradually wear out, becoming smaller, and can no longer perform their declared functions.

In this case, the solution to the problem is to replace the brushes with new ones. To do this, you need to gain access to the engine itself, remove it from the mounting socket, and carry out repair work. Replace brushes only in pairs, even if the second one is not too worn.

How to replace brushes and what to pay attention to - see the video:

Control module

A breakdown in the Whirlpool control module can be associated either with the burnout of individual elements or with the need to resolder the tracks. For an accurate analysis, you need to remove the control module in order to carry out high-quality diagnostics by checking the triac, resistor, and relay.

If damaged elements are identified, they are replaced with new ones. In cases where the board has been severely damaged and there are extensive melted areas, it may be necessary to replace it completely.

Bearings

With prolonged use of the Whirlpool washing machine, wear of the bearing assembly is possible. Such a breakdown can also be manifested by displaying the F06 coding on the display.

If the oil seal becomes leaky or loose due to vibrations, then water may seep into the motor. A washing machine with loose bearings does not operate stably, rattles and vibrates strongly, especially during the spin cycle.

Visually, water leakage from the seal can be seen when partially disassembling the Whirlpool washing machine. Such a failure requires replacement of the bearings. In some models with a non-separable tank design, it may even be necessary to replace the entire assembly.

Motor

If there is a problem with the motor itself, the Whirlpool washing machine may not spin the drum at all and issue F06. This situation can occur if there is a break or short circuit in the engine itself. This problem cannot be repaired - the motor must be completely replaced.

Let's check the thermistor

If the heating element has been fully tested and has proven that it copes with its functions perfectly, it’s time to check the thermistor. Just, it is located between the contacts of the heater. To remove the temperature sensor, perform the following manipulations:

• remove the chip with wiring from the heater contacts;
• slightly loosen the nut that holds the heating element;
• Carefully remove the thermostat from the housing.

The temperature sensor is a small metal cylinder. After the thermistor is removed from the washer body, you need to check the resistance in it using a tester.

• switch the multimeter to resistance determination mode;
• hook the probes of the device to the contacts of the temperature sensor. For example, if the temperature is 200°C, the resistance should be displayed on the screen, the value of which will be 6000 Ohms;
• lower the thermistor into warm water, watch the numbers change on the device screen. If the temperature sensor is working properly, the resistance will decrease, so at 50°C it will be about 1350 Ohms.

When the temperature sensor fails, the old part should be replaced. The thermostat cannot be repaired. If the element is fully operational, we continue the diagnostics further.