How to troubleshoot Atlant washing machines

Belarusian Atlant washing machines are distinguished by high-quality assembly and durable operation. It is not for nothing that the manufacturer gives a 3-year warranty on its household appliances.

However, even the most reliable devices fail over time. If the Atlant washing machine does not turn on, you need to focus your efforts on finding and eliminating the cause of the breakdown.

Read the article about why the device does not respond to commands and how to fix it.

Washing machine won't turn on

If the display does not light up when you press the power button, make sure the power cord is plugged in and there is electricity in the house. If the problem is in the washing machine itself, then the troubleshooting options and methods for eliminating them are as follows:

• Plug fault. Disassemble the plug and check the contact connections.
• Broken power cord. You need to ring the cord.
• There is a fault in the electrical wiring in the car. Remove the outer panel of the unit and check the condition of the terminal clamps, they may be oxidized.

If the display of the machine automatically reacts to turning on, the washing program is selected, and the machine does not work, the reason is as follows:

• Wrong washing mode selected.
• The door is not closed tightly enough. Check the integrity of the door seal and whether the item being washed has gotten between the door and the body.
• Water is not flowing into the machine due to the water supply taps being closed.
• The timer is faulty. In this case, the washing mode of the selected program does not start due to a broken time relay. To check, turn the program switch until the drum begins to rotate. If this happens, it means that the timer is faulty and requires replacement.

Is there current?

More often than not, the washing machine does not turn on due to problems with the external power supply. Therefore, before panicking and any manipulations, you need to check whether there is light in the room. All you have to do is flip the switch: if the light comes on, then we move on.

Next in line is the electrical panel. Here you need to see if all the machines are in the “working” position. Probably, starting a powerful washing machine overloaded the circuit, the RCD tripped, and the power supply was cut off in emergency mode. In this situation, it is necessary to reschedule the load on the network to eliminate overvoltage and current leakage.

Then we head to the power outlet and assess its condition. Telling signs will be the presence of melted plastic, dark spots on the wall and a burning smell. If there is no visible damage, we test the output by connecting any working device to the network. Do you have contact? Then we continue searching for the problem.

If you notice a burning smell, smoke or melted insulation, you must turn off the power and call an electrician - a short circuit has occurred!

If during the inspection alarming signs were found, then it is necessary to immediately turn off the power to the entire house and call an electrician. Self-repair of the electrical network is permitted only if you have the appropriate qualifications. In any case, it is prohibited to use electricity - a repeated current leakage with subsequent fire is possible.

Washing machine drum does not fill with water

First of all, check whether the water supply taps are open. Next, make sure that the inlet hose is not deformed or clogged. Rinse it if necessary.

If the inlet filter is clogged, perform the following manipulations:

• Close the water supply tap.
• Disconnect the hose from the unit inlet valve.
• Remove the filter and rinse thoroughly under running water.
• Install the valve, connect the hose and open the water supply valve.

If the intake valve breaks, it will need to be replaced. You can also do this yourself. It is necessary to remove the valve from the inlet pipes and replace it with a new one.

The water intake system is a weak point in Atlant machines. In good condition, when the water level in the drum rises, the water compresses the air in the pressure regulator compartment. When the pressure reaches the required value, the switch operates and the inlet valve closes. At the same time, power is supplied to the heating element and the switch for prohibiting premature opening of the drum door is activated. If the tube is damaged or clogged, the water supply system will not work.

To troubleshoot:

• Check how the tube is installed on the water level switch. If the end of the tube has hardened, cut it a couple of centimeters and put it back on the switch.
• To check that the switch is working properly, blow into the tube. The click of the switch should be heard.
• Afterwards, loosen the clamp on the hose that secures the pressure chamber to the drum.
• Flush the chamber so that the inlet and outlet ports are clean and free of blockages. Inspect the camera for cracks and deformations.
• Make sure the switch is working properly: test it with a multimeter. If damaged, replace with a new one.

"Electrics" inside the machine

After diagnosing external communications, it is necessary to deal with the electronics of the washing machine. Inside the machine, three “points” are responsible for transmitting current: the plug and the supply wire, as well as an interference filter. All elements are located together, so they are checked simultaneously.

The procedure is as follows:

• disconnect equipment from communications;
• remove the top cover;
• look at the left side of the lower corner, where the FPS is located;
• loosen the fasteners holding the power cord;
• pull out the cord along with the filter and plug.

It is not difficult to diagnose parts yourself. The first step is to inspect the plug for signs of fire. Next, we check the cord: set the multimeter to the “Buzzer” position and “ring” the wire for breakdown . If a current leak is confirmed, then you should not try to restore the insulation with twisting or electrical tape - this is unsafe and risks repeated breakage and fire! The element needs to be replaced with a new one.

The power cord cannot be repaired at home - if damaged, the cord must be completely replaced!

After the plug and cord, we inspect the interference filter. If there are no visible defects, turn on the multimeter to measure resistance and touch the contacts with the probes. When “0” or “1” appears on the display, the FPS changes.

Washing machine drum fills with water too slowly

Standard reasons why water fills slowly into the washing machine:

• The inlet hose is clogged or deformed. In this case, rinse the hose under water pressure.
• The inlet filter is clogged. Remove and wash the filter.
• The water pressure in the system is not high enough. Make sure the water supply valve is fully open. If yes, then there is insufficient water pressure in the line. It needs to be raised. For example, install a pressure tank under the ceiling of an apartment, or in the attic of a house. The minimum required pressure is 12 atm.

The water in the washing machine does not heat up. Heating element failure

Causes of breakdowns and options for eliminating them:

• The water level regulator is faulty. A faulty water level switch does not recognize that the drum is full, so it does not turn on the heating element. Check the switch with a multimeter and, if faulty, replace it with a new one.
• Scale has formed on the heater. Due to increased water hardness, limescale appears on the heating element, which affects the operation of the heater. Disassemble the washing machine and descale it.
• Malfunction of heating equipment. The heater contacts need to be tightened and oxidation removed. Using a multimeter, check the heating element for an open circuit by first disconnecting one wire from the heater. If necessary, replace it with a new one.
• Thermal relay failure. It is used to measure the temperature of the water in the washing machine tank and turn off the heating element when the desired temperature is reached. A malfunctioning thermal relay turns off the heating element incorrectly: too early or too late.

Determining faults by code

Atlant machines are equipped with a display that shows the selected operating mode, the amount of time remaining and the error code. The latter are of the following types:

• None;
• Door;
• from F2 to F15.

The appearance of one of these codes does not always indicate a malfunction. Knowing what a specific error means can help you narrow down your search for the problem. A specific code indicates the failure of a specific part. However, this only indicates problems with this element, although the fault may be hidden in other parts of the machine.

None

This signal indicates that due to the large amount of foam, the drum cannot rotate. If None appears frequently, it is recommended to replace the current washing powder with another one or select suitable operating modes.

Door

Door indicates that the machine door does not close. This problem occurs due to:

• door lock failure;
• damaged wiring supplying the central board;
• contact violations;
• improper installation of the washing machine;
• defective guide or clamp;
• skewed loops.

Some of these problems can be corrected yourself. To solve other problems, you will need specialized equipment to help assess the condition of the wiring.

F2

Code F2 indicates a failure of the temperature sensor, which occurs due to a violation of the integrity of the contacts (wiring) or a breakdown of the control unit.

F3

This error appears when the electronics of the washing machine detects a malfunction of the heating element. Failure of the heating element is caused by accumulated scale or broken contact.

F4

F4 appears if the water drainage is disrupted (water flows slowly away or stagnates in the tank). Basically, this code appears when the hoses become clogged or the pump fails.

F5

This signal indicates a blockage in the hose supplying water. Also, error F5 occurs if the inlet valve breaks.

F6

F6 appears on the washing machine screen if the reverse relay fails. This error also occurs in cases where the motor is faulty or the contacts are damaged.

F7

F7 reports insufficient voltage in the mains or a broken interference filter. In this case, it is impossible to restore the operation of the machine without the involvement of a specialist.

F8

Error F8 occurs if:

• the water inlet valve is jammed;
• the pressure switch is broken;
• The control board has failed.

Due to each such breakdown, water remains in the tank of the machine.

F9

F9 indicates a failed sensor that measures the engine speed. This malfunction also occurs due to broken contacts or broken wiring.

F12

This error appears when problems occur with the motor or control unit (triac on the central board).

F14

The appearance of this code indicates a software malfunction. The malfunction can be resolved by reinstalling the software.

Automatic stopping of the washing machine during a cycle

If the washing machine stops on its own during an incomplete wash cycle, check the presence of power in the outlet using a multimeter. If everything is in order with the power supply, the reason for the stop may be a clogged inlet or outlet hose. To remove the blockage, rinse the hose under the tap.

The next step is to remove and check the serviceability of the pump. It may be clogged or broken.

Next, check the serviceability and cleanliness of the intake valve. If necessary, replace with a new one. Next, check the operation of the thermostat, heating element and timer. If the timer malfunctions, replace it with a new one, as repairs are too difficult for a non-specialist.

A typical case when repairing an Atlant washing machine is the failure of the electric motor. The “weak link” in it is the brushes. Such repairs require special skills and it is better for the user to contact a service center. The good news is that in most cases the engines can be repaired and there is no need to buy a new one.

Atlant error codes.

Our website contains many articles about repairing washing machines of other brands, which you can read here.

The troubleshooting methods described in this article assume that the performer has certain knowledge, skills and tools. Therefore, if you are not confident in your abilities, seek help from a repairman.

The drum does not rotate

First, rule out the simplest reason - a broken door latch. If the lock is faulty, the drum will not rotate. To check, press the door button several times, it may be stuck.

If the drum in the washing machine is not mounted on a direct drive to the motor, but on a tension belt, the belt may come off. Move the engine down a little and adjust the belt tension tighter. Be careful not to overdo it. Too much belt tension will cause rapid bearing wear and failure. With the correct belt tension, when pressed, the belt moves about 12 mm. If your washing machine does not have a belt tensioner, the best alternative is to replace the belt with a new one.

Replacing the washing machine drive belt

Another possible reason for the drum stopping is a breakdown of the electric motor. In this case, you should contact a specialist.

Button that starts processes

After successfully diagnosing the power cord and FPS, we move on to the dashboard. The fact is that on Atlant washing machines, when one or more keys stick, a failure occurs, after which the entire system is de-energized. While modern washing machines can withstand such a shock and display a corresponding error on the display, older models cannot cope with the load and simply “go silent.”

To understand whether the problem is caused by a stuck key, you need to perform several steps:

• open the detergent tray and, pulling it towards you, remove it from the housing;
• Unscrew all the screws holding the dashboard;
• carefully disconnect the panel from the machine (you don’t need to completely unhook the board - you just need to gain access to the “internals”);
• switch the multimeter to resistance mode;
• Apply the probes to the button contacts and measure the resistance.

Diagnostics of the dashboard is carried out with the washing machine turned on.

Practice shows that sticking of the “Start” button more often leads to an emergency shutdown of the machine. If it works, then there is a problem with the other keys being used. We check everything sequentially. If sticking keys has nothing to do with it, then there is a high probability that the problem is in the electronic module. Here it is better to turn to specialists.

Interesting:

• The washing machine does not respond to the power button
• Beko washing machine does not turn on
• Electrolux washing machine fault repair
• Daewoo washing machine does not turn on
• Indesit washing machine does not turn on
• Whirlpool washing machine errors without display

Reader comments

• Share your opinion - leave a comment

Problems with draining water

The first possible reason for water retention in the drum is a clogged outlet hose or its deformation. Check the hose for blockages and flush if necessary. The exhaust filter may also be clogged. You can clean and replace it through the hole located at the bottom of the washing machine.

Cleaning the drain filter

The next possible cause is a clogged pump. Remove it and check for foreign objects. To do this you should:

• Prepare a rag for water in advance.
• Remove the clamps securing the hoses to the pump. Check the hose for blockages.
• Using a pencil, check the rotation of the impeller. If the impeller rotates slowly, remove the chip with wires and mounting bolts from the pump. Then remove the clamps or screws that connect the two parts of the pump.
• Mark or take a photo with your phone of their location so as not to confuse them when assembling. Check the impeller chamber for debris, and also make sure there are no threads wrapped around the shaft.
• Clean and reassemble the pump. If the above manipulations did not help, replace the pump with a new one.

Typical breakdowns

The Atlant washing machine has its own list of typical malfunctions that arise due to improper care, operating errors, and equipment wear. It is these reasons that more often than others lead to sad consequences, forcing the owner to stop washing and search for the source of the breakdown.

Doesn't turn on

In a standard situation, the washing machine starts, the drum rotates inside the tank, everything proceeds as normal. Any failure in a well-functioning circuit is a reason to pay attention to what exactly may be wrong.

Spin problems

Even if the washing was successful, you should not relax. It happens that the Atlant washing machine does not spin clothes. Before you start panicking about this, it's worth checking the wash cycle you've chosen. It is simply not provided for sensitive programs. If spinning is included in the list of washing steps, you need to understand the causes of malfunctions.

The most common of these is a clogged drain system. In this case, the machine cannot discharge water and then begin spinning. The breakdown may be caused by a failure of the pump or pressure switch or tachometer. If after finishing the wash there is water in the hatch, you need to check the drain filter by unscrewing and cleaning it of dirt. It is important not to forget to replace the container - after removing the obstacle, the water discharge will most likely proceed as normal. For more complex diagnostics and repairs, the equipment will have to be unplugged, manually drain the water and remove the laundry.

Sometimes the Atlant washing machine starts the spin function, but its quality does not meet expectations. An overloaded drum or too little laundry will cause the washed items to remain very damp. This happens especially often with equipment equipped with a weighing system.

Doesn't pick up or drain water

You can independently search for the reasons why the machine does not collect and discharge water without calling a technician. If water leaks under the door or flows from below, the pressure switch that determines the filling level may be faulty. If it breaks down, the equipment will continuously fill and drain liquid. Water can also remain in the drum, and a signal will be sent to the control module that the tank is empty.

If the machine is leaking from below, this may indicate a faulty drain hose or pipe. A leaking connection will cause fluid to leak outside the drain system. If a clog forms, it can lead to a massive flood in the bathroom.

Filling and draining water is directly related to the operation of the pump. If this element is faulty or the control system or software unit is faulty, these processes do not carry out normally. However, most often the culprit is a clogged filter - filler or drain.

It is recommended to clean them after each wash, but in practice, rarely does anyone follow these tips.

There may also simply be no water in the system - it is worth checking the operation of the water supply in other rooms.

Not warm

The washing machine can only heat cold water to the required temperature using the built-in heating element. If the door still remains icy after starting the wash, it is worth checking how good this element is. Another indirect sign of the problem can be considered a deterioration in the quality of washing: dirt remains, the powder is poorly rinsed, as well as the appearance of a musty, moldy smell after removing clothes from the tank.

It is worth considering that all these signs do not mean that the Atlant washing machine is necessarily broken. Sometimes this is due to the wrong choice of wash type and temperature - they must match the values ​​​​in the instructions. If, when changing the parameters, heating still does not occur, you need to check the heating element or thermostat for damage.

Extraneous noise during operation

The occurrence of any sounds during the washing process that are not directly related to the actions of the unit is a reason to stop it. Foreign objects entering the tank can damage the internal parts of the washing machine and cause blockages. However, the unit sometimes hums and makes noise due to completely natural reasons. That is why it is worth trying to establish the nature and localization of sounds more accurately.

Loud or unusual noise during wash or spin cycle

If your washing machine suddenly starts making loud noises or clanking noises during the wash cycle, you may have left coins, keys, or other foreign objects in your clothing pockets. If small metal objects from the drum fall into the tub, the washing machine may be seriously damaged. Therefore, it is important to check pockets before washing.

Another reason for unusual sounds may be a broken latch or door lock. The sound in this case will be buzzing and will stop when the door is closed.

If a squealing sound appears when washing at high speeds, this indicates that the drive belt is slipping. Tighten the belt or replace it with a new one

If you hear a rattling noise when the drum rotates, the drum bearing is broken and needs to be replaced.

What can be done to ensure that breakdowns occur as rarely as possible?

A washing machine breakdown is an unpleasant situation, to put it mildly. No one wants to do laundry by hand or carry pounds of laundry to the laundromat. In order for your Atlant, an automatic washing machine, to work for a long time and not require the help of repair service employees, you should follow some simple rules for operating the equipment:

1. Follow the rules for using the equipment described in the technical documentation supplied with the machine.
2. If the washing machine runs all day, washing one load of laundry after another, you should take a break of 1-2 hours between washes.
3. Carry out antifungal prophylaxis of internal surfaces, and, if necessary, treat affected areas with special means.
4. Use high-quality laundry detergents, as well as special compositions for cleaning the washing machine and descaling. If the water is too hard, add softener to your laundry detergent every time you wash.

In the video below, the man talks in detail about how to independently fix most of the minor problems that periodically arise when operating a washing machine. After watching the video, you can not only clean the filter or powder compartment yourself, but also perform simple operations to replace electronics.

The times when domestically produced washing machines were inferior in quality to foreign analogues are a thing of the past. Modern Atlant machines with a built-in self-diagnosis system promptly inform the user about problems, allowing you to independently monitor the condition of the equipment.

Strong vibration, spontaneous movement of the washing machine on the floor

If a similar problem occurs for the first time, the reason lies in an overloaded drum of the unit or in clothes unevenly distributed in the drum. Remove excess clothing from the drum and continue to follow the recommendations of the Atlant washing machine manufacturer.

If the unit vibrates more than once, while moving along the floor, it means that the washing machine was installed incorrectly, not level. Re-align the unit by adjusting the height of each leg.

Interference filter (FPS): meaning and performance check

The control module, electric motor and other parts create radio frequency waves when the washing machine is running, which can harm other household appliances located near the machine. To protect electrical devices, the machine is equipped with an interference filter. If it malfunctions, it will create an obstacle to the passage of electric current. This will be the reason why the automatic machine does not start the washing process. To check the functionality of this part, you need to diagnose the wires at the input and output, as well as the device itself using a tester. If the FPS does not work, you need to order a new filter from the service center or make a request for its replacement.

Washing machine door won't open

The most common reason for the door blocking is water left in the tank after washing. Drain the water from the drum using the drain mode. Check for blockages in the drain pipes and whether the pump is working correctly.

We shared with you the most common causes of breakdowns of Atlant washing machines and gave fairly detailed instructions for eliminating them. Follow the manufacturer's recommended operating rules, and your assistant will serve you longer.

Rules that will help extend the life of your washing machine:

• Before loading items, check pockets for coins, keys, and other items and debris.
• Clean the heating element regularly to remove scale.
• Use hard water softeners and a cleaning filter.
• Regularly clean the drain filter of debris and dirt.
• Wipe the powder and additive drawer dry after each wash to prevent mold from forming.

Recommendations for troubleshooting problems in SMA Atlant

_____________________________________________________________________________

_____________________________________________________________________________

• Malfunctions, repairs and settings of Atlant washing machines

The Atlant 40M102 washing machine worked for six months without any problems. And recently I discovered that the water was not draining. The programs work, the device only makes a hum. What is the reason? The main source of problems is a breakdown of the drain pump. There was a problem with the operation of SMA 50U81. The unit does not fill with water and the washing program does not start. What is the problem and what should I do to fix it? One of the options is that the filler valve that supplies water to the unit has failed. A valve that is not working must be replaced. Three months ago we connected a 40M102 washing machine. It worked well. Yesterday my wife decided to wash things, but the machine cannot turn on. The screen does not light up. For what reason could this happen? One of the options is that the control unit, which provides the impulse to start the equipment, is faulty. This morning there was a problem. The Atlant 50U81 washing machine cannot open. It looks like the door is jammed. Why did this happen? It can be assumed that there is a malfunction of the UBL. Can anyone tell me why the drum doesn't rotate? The 40M102 machine has only been in operation for six months. The main source of this problem is wear of the drive belt or motor brushes. The machine, model 50C101, takes a very long time to collect water for washing. The water intake hose has been replaced. The pump must have failed. The probable cause is not due to pump failure. I suggest turning off the water supply to the washing machine. Unscrew the inlet hose from it. Check the water pressure in the hose. Next, clean the filter mesh in the water inlet solenoid valve. Malfunction of the Atlant 50C102 washing machine. It gives error f3, the repair was carried out 2 times, six months have passed since the repair. What could be wrong and how much will the repair cost? The interpretation of error F3 is as follows: Malfunction of the heating element (heating element), malfunction of the electronic module, broken wiring or poor contact in the connectors. Model 50С82. Model with LEDs. After selecting a program with the selector, the indicators corresponding to the specified program are displayed for a split second, and then the 2, 3, 5 LEDs in the bottom row begin to blink. The hatch is not blocked. I suspect error F13 (control module malfunction). Tell me, please, will the firmware help? Or a problem with the processor? The board may need to be re-flashed. SMA Atlant 50U102. I stopped the wash a couple of times, expelled the water and displayed error F8. Now it takes in a little water, immediately drains it and displays error F15. We've been using it for six months. What could be the reason? Error F8 - Level sensor-relay - Check contacts, cylinder tightness, replace level sensor-relay or control module. Error F15 - Water leakage (In units with an aquastop system) - Eliminate the causes of the leakage. A coin got into the SMA drum model 50U107, it can be seen through the holes in the drum, it is located near the drain hole. What can be done about this at home and how will its presence affect the operation of the unit? Removal required. Otherwise the tank may be damaged. Washing machine 50U82. The problem appeared after overloading the laundry; it got stuck on the spin cycle with error F9. According to the service manual, this code indicates a problem with the electric motor or module. Now, when starting the cycle after preliminary filling, along with the main filling, the electric motor turns on at increased speeds and displays error F9. Or, for example, during forced draining, simultaneously with the pump, the electric motor turns on at high speeds and the same F9. The electric motor was checked separately from the body; it rotates normally, does not spark, and there is no wear on the brushes. The resistance of the rotor and stator windings is 3 ohms, tacho is 16 ohms, the wiring from the connector on the electric motor to the module slot is normal. A BTB 16600 triac was added to power the electric motor, although the old one was normal, I ran a cartoon over the board and there were no broken elements. Error F09 - the tachogenerator is faulty, and according to the signs it is. Check again more carefully the tachogenerator itself on the engine and the circuit on the board to the processor. Atlant 50U87. During washing, the machine began to drain water, but not with much pressure, one might say it was leaking. And it was also discovered that water was poured into the wrong cell, as usual. The drain pump and drain pipe (drum-pump) are free of foreign objects. Is it possible to think about the control unit? INVENSYS 475710 control module. And what does self-draining depend on: is the problem in the pump or in the block? Just lift the drain hose higher and see if water flows out during the wash. Tell me, what do the SMA Atlant error codes mean? Sel — Interface module selector failure. None - Excessive foam formation. F2 - The temperature sensor is faulty. F3 - The heating element (heating element) is damaged. F4 - Malfunction of the drain pump (pump). F5 - Fill valve failure. F6 - Problems with the electric motor relay. F7 - Electrical problems. F8 - Too much water in the tank. F9 - Problems with the engine tachometer. F10 - Failure of the UBL (hatch lock). door — UBL lock malfunction. F12 - Motor triath malfunction. F13 - Problems with wiring or contacts. F14 - Program failure. F15 - The tank has become depressurized. When turned on, the 50U88 machine constantly beeps, draws water, turns it a couple of times and turns on again; it stands still, does not drain or spin, does not reach this stage. And so on for all washing tasks. What could it be? The machine indicates an error. Diagnosis by a specialist is required. The Atlant 50C81 washing machine is in operation. Instead of rinsing, I accidentally turned on the express wash and, already during the cycle, tried to switch to rinsing without stopping the unit. Then I stopped it, set it to rinse and turned it on. The traffic jams were immediately knocked out. The next couple of starts are the same. With these manipulations you could not break her. If the machine knocks out, it means something is faulty. You need to call a specialist. Washing machine 70С1010. Tell me, has anyone encountered such a problem. When washing, water began to run out from under it. As soon as the wash started, it took in water, the drum began to spin, and at that time water and powder began to flow out from under it. This started after accidentally washing a pack of toothpicks in my jacket. Naturally, all the toothpicks were removed from the filter. Tell me what needs to be checked first? Place newspaper under the unit and start drawing water. Remove the newspaper from underneath it regularly until drops of water appear on the newspaper. This way you can pinpoint where the water is dripping. Tilt the unit onto the back wall, or place it on it and use a flashlight to look for where the leak is (perhaps a toothpick has pierced the rubber pipe). SMA Atlant 50С101. You start the washing mode - it fills with water, the motor does not rotate, but the relays click as expected. The error is indicated by blinking of the second and fifth indicators. Tell me, what is this error F9? If you turn on the drain or spin mode, the drain pump operates jerkily for about 1 second, it stops working for 3-5 seconds, then the same error occurs. There are no breakdowns on the engine. The tachometer is 180-190 Ohm, if you turn the engine the resistance drops. The heating element, of course, needs to be replaced, a breakdown on the body, but even with the heating element turned off, the error does not change (I didn’t have such a long one with me to replace it). By the way, who knows what power the heating element on this model is 1900-200W? One terminal on the capacitor melted (replaced, of course). There is scale on the module around the PWM controller. Help me determine the error code. Is it possible to install a module from 50C102? Yes, just to check. There is not scale around the shim, but most likely coal dust. You should check the brushes on the engine. The contact pad on the board where the motor connector is inserted may burn out. Also ring the motor from the board connector. SMA 50C102 door error. The track burned out and the TS03 triac burned out. I don’t have such a triac, and I don’t know the markings. I inserted a triac analogue of the motor control, it is larger than the TS03. I launched it, the UBL worked, it worked for 20 seconds and gave an error F10. So I understand that the processor does not see the activation of the UBL. He rang all the resistances coming towards him, intact. Maybe it's the triac? Tell me the marking TS03, or an equivalent. I set it to spin, after the UBL is triggered, the pump starts, then the engine, it works normally with reverse, and then the F10 error appears and stops. You need to start by replacing the UBL. UBL's original triac is T4 0560. My Atlant 50C82 washing machine makes squeaks during washing, and during spinning the squeaks intensify. It's the spring. Replacement required. Washing machine Atlant 50U102. When you turn on any program, all the icons on the screen light up one by one, and the washing time changes accordingly. Doesn't respond to the START/PAUSE button. How to exit this demo mode? As far as I know, these models do not have a demo mode. Apparently, the fault lies either in the interface board or in the cable. Use the method of elimination, check and clean all connectors, ring the cable wires. Model 50U107. When turned on, it fills with water and at the same time drains by gravity. Raise the siphon. The washing machine 50U82 is in operation. On any washing program, it takes in water, makes two to four revolutions and freezes for 10 minutes, then drains the water, the spin starts, but the drum does not spin. In the rinse program, all cycles work well: water is added, the drum rotates for the required time, the water is drained, and the laundry is spun. Presumably, the heating element or electronic control module is faulty. Please tell me, the Atlant 50U87 machine did not drain the water during washing, it drained it itself through the bottom pump. I turned it on - the buttons light up again, but it doesn’t turn on. What could it be? Most likely the drain pump is faulty. Atlant 50U88 car. The water is draining and there is a grinding noise, what could this be? And the cost of repairs. The drain pump is noisy when operating. The pump impeller may produce increased noise (replacing the pump assembly). Other reasons are possible, for example, a “foreign” object catches on the impeller. Model 50С81. This SMA has LED indication. On the second row, 2 3 5 indicators flash. Doesn't react to anything. You press anything, it just beeps. Tell me, please, will the firmware help here? If yes, where can I get it? Check the operation of the UBL first. When you turn on any program (wash, spin, drain), the Atlant 70C1010 machine buzzes, but the program is not executed. Could some kind of drive belt come off there? Is it difficult to replace it yourself? When washing, the SMA should initially hum differently than when draining and spinning, since it performs different operations: in the first case, it pours water, and in the second, it drains. If everything happens as you describe, this may mean that the electronic module, when starting the program, sees some kind of critical error and turns on an emergency algorithm, in which the drain pump immediately turns on (buzzes), and the program itself does not execute. I have small children and a big problem - the Atlant 50C101 machine has broken down - the third indicator in the second row (rinsing) is blinking. But when I took out the laundry, miraculously opening the locked door, the water was hot. Is it possible that this is the wrong error and I can fix it without a wizard? Error F2 - malfunction of the temperature sensor, heating element, control module. We need the size of the oil seal and tank bearings for model 50C102. Oil seal 25x47x8.5/11.5 and bearings 6205 / 6204. Model 50U102. The wash does not start when pressing the Start button. Previously, during washing it showed error F4, that is, a problem with the drain. But the drain works. If you force air into the pressure switch so that the maximum operates, the pump turns on, giving error F8 (overflow). Could the reason lie in UBL? And somewhere I came across that the engine could have broken down, it won’t start because the UBL and the engine are in the same circuit? I had a similar problem. The problem was solved by replacing the interface module. On the old one, the contacts for the start button cable were oxidized, and perhaps this oxide shorted the contacts, which caused the malfunction of the SMA. In the Atlant 50U107 washing machine, two out of three plastic parts broke inside the drum. Tell me, please, is it possible to replace them? Replacement is possible. SMA 50С82 2011 When the power is on but the mode is off, there is a phase hanging on the drum. Call an electrician. It is important to connect the ground when installing the unit. During the washing process in the Atlant 50U82 machine something drums. When you manually rotate the drum, something knocks, as if there were some pieces of iron there. What could it be? Probably, foreign objects have entered the working volumes (between the tank and the drum). SMA 50U87. After selecting a program, the display shows error F9. The circuits from the engine to the module rang. Engine relays are working. There are no jerks, the drum just doesn’t spin and that’s it. The Tahoe seems to be intact, but if, say, you set it to any program and then turn the dial to turn off the SMA and then turn it again either to the left or to the right, the engine once picks up strong speed clockwise and stops and that’s it, the program selection board is on and then again F9. Tahoe is normal, brushes too. What is the reason? Ring the transitions on the back side of the board from the relay to the pads for the motor connector. I hope that the relays themselves are beyond suspicion. SMA Atlant 50С102 - Water boils in any program. Thermal sensor is ok. What to see? Perhaps the heating element is broken or the heating element relay is stuck in the on state.

_____________________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

_____________________________________________________________________________

Troubleshooting and breakdowns in the Samsung SMA Need advice on how to repair the Samsung WF 7452S9 R washing machine. The following happened: the automatic plug breaks when starting the rinse or wash program modes. Read more

How to troubleshoot problems with Beko WMN washing machines. Washing machine WMN 6510 N. When spinning, the tank begins to shake violently and the rubber cuff of the tank begins to slam. At the very beginning of operation in October 2002, the same thing happened. Called the master Read more

Problems with Bosch WLG washing machines - Repair recommendations When the WLG20265OE washing machine operates in any mode (spin, rinse, wash) when setting any speed (100-1000), the machine reaches maximum speed Read more

Questions about operation, malfunctions and service of the AEG SMA I have an AEG AMS 7500i (narrow) machine. When washing, a squeaking (grinding) sound occurs, similar to the squeak of rubber. What could this be and could it cause it to break? What you need Read more

Tips for troubleshooting SMA Ardo SMA SE 1010. It rattled in the pump area, the laundry came out wet. A coin was found in the filter. I removed and disassembled the pump. It turned out that the rotor is something like Read more

Questions about the operation and breakdowns of the Siemens ACS In operation WM10N040OE. When water is drawn into the drum, when turned on, water immediately begins to flow from below. I checked the hoses - they are intact, but they are leaking from all sides. Please tell me what the problem is and how Read more

Problems, adjustments and settings of Whirlpool AWG washing machines Model AWG 223. Was washed for 2 years without problems. Now I have stopped spinning in the rinse-spin mode, just spin. Haven't tested it in other modes. The drain pump is heard, the drum is spinning, but Read more

Recommendations for troubleshooting in SMA Atlant The Atlant 50C81 washing machine is in operation. Instead of rinsing, I accidentally turned on the express wash and, already during the cycle, tried to switch to rinsing without stopping the unit Read more