In this article we will look at how to repair an Electrolux EWS 1046 washing machine when the machine does not drain water . This can happen for two reasons: blockage or pump failure. In both cases, the pump will have to be opened. A small digression. You need to open the machine if you have already checked the filter, the drain hose and all the joints associated with it, as well as the sewerage system. Only if the above measures did not help you need to open the washing machine.
To begin, remove the top cover; it is secured with two self-tapping screws with an 8mm head. The cover is removed backwards.
Below it you will see six bolts. Remove only the four rear screws, two on each side.
On the bottom sides, under the plugs, which are best removed using something thin, there are two more self-tapping screws.
In general, I would like to say that all repairs for Zanussi and Electrolux washing machines are similar in structure, so if you haven’t found your model, don’t be upset, they are almost the same in layout. On some models there are also two screws on the back cover. Then, pressing the latches on the sides, remove the casing on which the inlet hose and power cord are attached.
Now you can remove the back panel. The following view opens for you.
There are two options for pump location. The first is indicated by a green circle, the second is indicated by a red circle. If there are two pumps, then you need a red one, if there is one, then green.
This is what the distant pump looks like. Unscrew the three screws and it's yours. After cleaning or replacing the pump, reassemble the machine in reverse order. If you do not want to do the repairs yourself, we recommend that you contact a specialist. This will allow you to quickly return the equipment to serviceable condition and avoid unforeseen situations. In addition, the cost of the service is reasonable. Using professional equipment, we will replace the pump and provide all the necessary guarantees. The repair price is 1800 rubles.
In this article we will look at how to repair an Electrolux EWS 1046 washing machine when the machine does not drain water . This can happen for two reasons: blockage or pump failure. In both cases, the pump will have to be opened. A small digression. You need to open the machine if you have already checked the filter, the drain hose and all the joints associated with it, as well as the sewerage system. Only if the above measures did not help you need to open the washing machine.
To begin, remove the top cover; it is secured with two self-tapping screws with an 8mm head. The cover is removed backwards.
Below it you will see six bolts. Remove only the four rear screws, two on each side.
On the bottom sides, under the plugs, which are best removed using something thin, there are two more self-tapping screws.
In general, I would like to say that all repairs for Zanussi and Electrolux washing machines are similar in structure, so if you haven’t found your model, don’t be upset, they are almost the same in layout. On some models there are also two screws on the back cover. Then, pressing the latches on the sides, remove the casing on which the inlet hose and power cord are attached.
To safety information, Installation and maintenance, Child safety
During use, Safety information
- Image
- Text
/To
Safety information
manual, including all instructions and warnings, carefully before installing and operating your washing machine This will ensure that your machine runs smoothly at maximum efficiency. Anyone using this washing machine should be familiar with the machine's operating and safety instructions.
Installation and Maintenance
•
Before using the washing machine, remove all packaging material and transport locking devices. Failure to comply
This requirement may result in damage to the machine and other property. See subsection “Transport Locking Devices”.
•
All installation and maintenance work on the device must be carried out by a qualified technician. Repairs performed by untrained persons may seriously damage the instrument and result in personal injury or property damage. Before you begin any manipulations with the washing machine, be sure to unplug it.
•
The machine is heavy, so be careful when lifting it. It is forbidden to lift the car
holding the control panel, door, or storage tray
detergent.
•
Avoid installing the machine in a room where there is no floor drain.
•
The power cord plug must be plugged into a grounded electrical outlet located in an easily accessible place. Fixed connection of the device must only be carried out by an authorized electrician.
•
If the power cord is damaged, it must be replaced with a special power cord recommended by your appliance manufacturer. Contact authorized service centers.
•
When connecting or cleaning the machine, make sure that the power cord is not pinched or damaged in any way.
either way and that the hoses are not torn or kinked.
•
When installing the appliance on a carpeted floor
It is necessary to ensure that the lower ventilation openings are not blocked.
•
Maintenance and possible repairs should
carried out by specialists from an authorized service center. Never attempt to repair your washing machine yourself.
Child safety
•
The washing machine is intended for use by adults only. Do not allow children to play with controls or other parts of the machine.
•
Please note that the plastic bags included in
packaging of the device are lethal
danger to small children playing with them.
•
Before loading the machine, make sure there are no foreign objects or pets in the drum.
•
The door glass becomes hot when the machine is running, so do not touch it. Don't let
children to a running car.
During use
•
The machine is intended for normal washing only.
at home and only in accordance with the instructions,
given in this manual. Using the machine for other purposes is risky and may result in personal injury and damage to the machine and other property.
•
Only items that are suitable for use can be machine washed.
machine washable. If in doubt, contact the manufacturer or retailer of the item.
•
Follow the directions on textile labels and make sure pockets are empty and buttons and zippers are closed before washing.
•
Hard objects such as coins, pins, nails, screws, etc. can cause serious damage to the machine. Make sure the pockets are empty before loading clothes into the machine.
•
Remove rust, ink, paint and grass stains before machine washing.
•
Do not machine wash torn or heavily worn items.
•
Wash small items such as thin socks, ties,
lace collars and products, in mesh laundry bags to
1 prevent them from getting between the internal
and external drums.
•
Items treated, for example, with rust removal chemicals, liquid household chemicals, etc., should be thoroughly rinsed by hand before washing in the machine.
•
When washing bras with wires in the washing machine, they should be in mesh bags
for linen.
•
Use only detergents that are specifically designed for washing machines.
•
Always follow detergent and fabric softener manufacturers' recommendations when determining the amount of these substances to use. Too much can ruin your laundry.
•
Do not overload the machine. Deteriorates when overloaded
characteristics of machine operation and possible damage
linen
•
Before opening the machine door, make sure that the water has been completely pumped out.
•
Do not leave the machine running unattended.
•
When finished, disconnect the machine from the sources.
water supply and electricity. When unplugging the cord from an electrical outlet, hold it by the plug, not the cord.
•
When the machine is not in use, keep the door loosely closed to prevent musty odors.
•
Before cleaning the machine, carrying out work on
maintenance, make sure that the machine is disconnected from the power supply.
21
Electrolux fault codes
The self-diagnosis system allows the user to determine the cause of the malfunction. When the fault code is displayed on the display, you just have to find out its meaning. Then troubleshooting will be quick.
Let's look at the main Electrolux error codes:
| Error code | Code meaning |
| E11 | No water supply. |
| E13 | There is a water leak. |
| E21 | Error draining water. |
| E23/E24 | There is a problem with the board's triac, which is responsible for the operation of the pump. |
| E31/E32 | Pressostat failure. |
| E33 | The heating element does not work. |
| E35 | Overflow of water. Exceeding the normal level. |
| E36 | The heater protection sensor has failed. |
| E38 | There is a problem with the pressure switch. |
| E39 | The overflow sensor is faulty. |
| E41/E45 | Broken mechanical lock, UBL, door handle. |
| E51/E54 | Problems with the control module. |
| E55 | The SM motor or its wiring is faulty. |
| E56 | Tachogenerator failure. |
| E57 | The voltage in the circuit exceeds the permissible limits. |
| E58/E59 | Error in the operation of the electric motor. |
| E5A/E5E | Control module error. |
| E61/E62 | The water gets too hot. |
| E66 | Problems in the operation of the heating element. |
| E71 | Problems with the thermostat. |
| E72/E73 | Damage to the drying temperature sensor. KZ. |
| E74 | The thermistor is not positioned correctly. |
| E82/E84 | Main module malfunction. |
| E85 | Pump problem. |
| E91 | There is no communication with the control module. Wiring fault. |
| E92/E99 | Error in the control board. |
| EA1/EA6 | The DSP has failed. Worn drive belt. |
| EB1/EB3 | Problems with wiring. Incorrect voltage. |
| EF1 | The water did not drain after the timeout expired. |
| EF2 | Too much foam. |
| EF3 | Problems with the pump. |
| EF4 | The flow sensor does not give a signal. |
| EF5 | Drum overload. Stopping the operation of the SM. |
| EN1 | Power failure. Problems with the electronic board. |
| EN3 | Insufficient voltage in the network. |
| ENE | The circuit protection relay has broken. |
| ENF | Circuit relay not recognized. |
Electrolux ews 1020 does not fill with water
Post by Cloun » 04 Jan 2010 14:38
Good afternoon everyone. There is (or was) an Electrolux ews1020 SM. Product number 914756550. It worked for three years without any complaints. The operating mode is constant but moderate. The supply of water and electricity in the house is stable and good. The machine is grounded and connected correctly. Yesterday I was upset. After the wash cycle, the laundry was washed, but not rinsed or spun. When you try to start the rinse, spin (or any other) mode, the drain pump motor turns on and the program does not end. I checked the network - ok, input-output filters ok. I set it to self-diagnosis (position 0, two buttons - power - held down the buttons) the diodes blinked. Turning the regulator clockwise - the drum of water was almost full, I turned the regulator - the drum began to spin and water began to splash out. To stop the disgrace, I turned off the network with a button. When the network was turned on again, the machine spun the drum for a long time with the regulator in position O. I pressed the same buttons as when entering the diagnostics - the machine returned to its original working (or rather non-working) state. Only now this bastard won’t let me into self-diagnosis mode. Doctors what's the prognosis? Will the lazy woman live or will he suffer? Today I took care of the peripherals - I rang the windings, washed and blew out the hoses, checked the contacts. I didn’t find any crime, but the patient was in a stupor. Sorry for the abundance of letters. Can you tell me if I can go into diagnostics or oops? Thanks in advance for everything.
PS. After a large number of tests and double-checking the contacts, the machine started rinsing once, added water, turned the drum and went into eternity pumping out water without stopping. There is silence when trying to enter test mode. Help!
Source
Bearing wear – from RUB 3,800*
Bearings are responsible for the smooth rotation of the drum. As the SMA is used, and also due to its overload with linen, the omentum weakens. Moisture gets into the bearing and the corrosion process begins. Over time, the bearing deteriorates.
SIGNS
The Electrolux washing machine makes unusually loud sounds when operating: creaks, rattles, crackles. This can be heard especially clearly when the SMA is operating at high speeds. If you shake the drum with your hand, you may notice that it “dangles” more than usual. When disassembling the machine, rusty traces of moisture leaks from the bearings are visible on the tank.
If the bearings are completely destroyed, the drum may completely jam or fall down. The breakdown may be accompanied by code E50.
HOW TO FIX
The bearings need to be replaced with new ones.
*Rates are only for the work of the master; new oil seals and bearings are paid separately.
Mazmuny, Siz oyymyzda boldynyz, Tutynushyga komek, kyzmet corset
Page 2
- Image
- Text
MAZMUNY
1. SAKTYK SHARALARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. KAUIPSIZDIK NUSKAULARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. BUYYM SIPATTAMASY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. BASKARU PANELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5. ZHUU BADARLAMALARY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. PAIDALAN KOLEMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7. FUNCTIONALAR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8. BIRINSHY KOLDANGANGA DEYIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 9. ӘRKҮNDIK KOLDANU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . eleven
10. PAIDALY NUSKAULAR MENEN KEGESTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 11. KUTU MENEN TAZALAU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 12. AKAULYKTY TҮZETU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 13. TECHNICAL SIPPATAMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SIZ OYYMYZDA BOLDYҢYZ
Electrolux kurylgysyn satyp alganynyzga rakhmet. Siz ondagan zhyldar boygy kasibi tazhiribe men
innovation suyeniip zhasalgan kurylygyny tandadynyz. Tapkyrlyktyn tuyndysy bolgan, koz tartarlyk
bul kurylgyny zhasau barysynda siz oyymyzda boldynyz. Sondyktan, koldangan sayyn tamasha natizhege
If you need a lot of information, please contact us. Electrolux alemіne қosh keldinѣіz. Bizdin website baryp kelesin karanyz:
Koldanuga katysty kenester, kitapshalar, akaulykty tuzet, kyzmet corset turals akparat:
www.electrolux.com
This young lady will tell you about the corset on the other hand:
www.electrolux.com/productregistration
Kerylғynyzғa kazhetti kerek-zharaktardy, shyғyndy materialardy and no firmalyk kosalky
bolshekterdi satyp alu ushin:
www.electrolux.com/shop
TҰTYNUSHYGA KOMEK, KYZMET KORSETU
Firmalyk zattardy koldanuda usynamyz.
Kúzmet corset ortalygyna khabarlaskanda kelesi derekterdin dayyn boluyn kamtamasyz etiniz.
Direct technical equipment. Please contact us
Eskertu / Abaylanyz - Kauipsizdik turals manyzdy maglumat. Zhalpy maglummattar menen kenester Қorgagan ortaga ziyan keldirmey paidalanu turaly nusqaular
Ondirushi eskertusiz ozgeris engizu kukygyna i.
2
www.electrolux.com
Tools for disassembling the device
Unlike other manufacturers, Electrolux provides the ability to replace parts. To get to the inside of the device, you need to unscrew several screws or bolts. Some parts are secured with clamps.
To troubleshoot problems, you will need a standard set of tools that almost every owner has:
- flat and Phillips screwdrivers for different thread diameters;
- ticks.
However, to disassemble some models, you may need other tools. We recommend that you have:
- wrenches;
- round nose pliers;
- chisels;
- hammer;
- stationery knife;
- universal key;
Be sure to read the device instructions before starting work.
Most Electrolux washing machines have similar design features. But to avoid mistakes, we recommend that you carefully study the manufacturer’s recommendations, paying special attention to the type of engine. Inverter-type motors are connected directly to the drum, while commutator-type motors are connected by a belt and pulley. Next, evaluate where the heating element, pump and pipe are located.
