Ariston washing machine does not turn on - reasons and repairs

Almost every modern family has a household appliance such as a washing machine. But, unfortunately, even the best quality products sometimes fail. But the situation when the Ariston washing machine does not turn on can undoubtedly be called a serious problem. However, you should not immediately call a household appliance repairman, because in some cases you can fix the problem yourself. But, first of all, you need to figure out what the cause of the breakdown is.

Ariston margarita 2000

The Margarita 2000 car has a stainless steel tank. The bearings are installed in a removable crosspiece mounted on the rear wall of the tank - it does not need to be removed to repair the bearing assembly. Repair sequence:

  1. Tighten the transport bolts.
  2. Remove the hatch on the rear wall of the device.
  3. Unscrew the fastening nut and remove the pulley using two screwdrivers.
  4. Remove the top cover and remove the counterweight.
  5. Place the machine on the front panel, having first removed the door.
  6. Unscrew the fasteners of the removable crosspiece of the tank.
  7. Using gentle blows, remove the cross from the shaft.
  8. Remove the oil seal and bearings from the crosspiece. Replace, lubricate and reinstall.
  9. Place the crosspiece on the shaft and carefully hit the bearings with a rubber mallet.
  10. Secure the crosspiece and pulley, put on the belt.
  11. Place the machine vertically and check the smooth rotation of the shaft.
  12. Install the front door, top cover and rear hatch.

Do-it-yourself repair of the Ariston Margarita 2000 washing machine is completed.

DIY repair

Knowledge of the structure and circuitry of the Ariston automatic washing machine will help you determine the breakdown. The picture shows the location of the main nodes of the MCA.

Let's figure out how to independently repair the Hotpoint Ariston washing machine.

Removing blockages during washing machine repair at home

It is easy to remove the blockage with your own hands. You need to check the drain filter, which is located at the bottom right under the panel.

By cleaning the filter, you will eliminate the cause of the washer malfunction. The drain pipe becomes clogged less often because it is thick.

The pump may become clogged, but this is rare because there is an additional filter in front of it.

The drain hose only becomes clogged if you installed it incorrectly.

Check the drain, it may also be clogged. Disassemble the unit, remove the pipe, loosen the clamps, and wash it. Remove the pump by unscrewing the fasteners and disconnecting the sensors.

Fill valve broken

If the fill valve in Ariston is broken, then water constantly flows into the washing machine, even when it is not working and is disconnected from the network.

To check the fill valve, you need to unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the body of the electromechanical unit.

Check the gaskets first. If they have not lost their functionality, measure the valve resistance. Place the probes on the contacts of the filler valve and check the resistance to see if it corresponds to the optimal value (from 30 to 50 Ohms).

If it is less or more than expected, it means that the water intake valve is not working. To replace it, you need to unscrew the old valve from the body and screw in a new one. Be sure to connect the sensors.

Water inlet valve malfunction

If the filling valve of an Ariston washing machine is broken, it does not shut off the water, and it flows into the tank itself, even if the equipment is unplugged from the outlet. This malfunction can be determined by the murmur of water, which is heard when the machine is turned off. To repair the part, you must disconnect the washing machine from the network and water supply and remove the top cover.

The water inlet valve is installed at the top, in the place where the inlet hose connects to the washing machine. First, you should inspect the gaskets for integrity, and then take a multimeter, switch to resistance measurement mode and install the probes on the sensor contacts. If it is working properly, the display will show a value ranging from 30 to 50 ohms. A broken valve cannot be repaired, so the part must be replaced. The process is very simple, just disconnect the wires, unscrew the faulty element and replace it with a new one.

Ariston heating element repair

To get to the heater, you will need to remove the back wall of the Ariston washing machine. There is a heating element at the bottom, as shown in the photo.

Before removing the electric heater, measure its resistance with a multimeter. An indicator of 1 Ohm indicates an open circuit, about 0 Ohm - a short circuit has occurred. A working device will show 25-30 ohms.

Attach the tester as in the photo:

If the part is faulty, replace it. Video to help you:

Bearing repair

The bearing in the drum may break and wear out. It needs to be replaced. You only need to buy a bearing of the appropriate brand in a specialized store or order it on the official website of the Ariston washing machine, or perhaps purchase it at an equipment repair shop.

Using a metal rod and hammer, knock out the bearings. If they are defective, replace them. If the drum is deformed, replace it with a new one.

Reassemble. If the fault is in the plastic fin, then there is no need to disassemble the tank. The washing machine door can be removed. Take a metal rod whose diameter is smaller than the holes in the plastic rib of the drum.

The rod is inserted into one of the holes on the edge, the latch is opened with the help of it, and the plastic part is removed. A new plastic rib is placed in its place. Slide the plastic edge along the groove until the latch fits into the hole and closes.

Bearing replacement: procedure

To replace the bearing, you need to get to the washing machine drum on which it is installed. The car is disassembled, gradually removing all the parts from it.

Emptying the washing machine tank

The body of the unit begins to be disassembled from the cover by unscrewing two bolts located on the top on the far side. To do this you will need a Phillips screwdriver. Once the bolts are removed, the cover must be pushed forward towards the scoreboard and then removed.

To remove the dashboard , open the detergent compartment and remove it by pressing the latch in the center. In the resulting niche you can see several bolts and several more on the opposite side of the panel. The bolts are unscrewed, all the plastic latches are opened, after which the wires are disconnected and the panel is removed to the side.

Avsl 100

The AVSL 100 model has a malfunction that is not found in other Ariston machines. When the washing mode starts, all the indicators light up, but the wash does not start, water does not fill, and the drum does not spin. The device is not equipped with a self-diagnosis function, so the malfunction cannot be determined by the error code.

Users have determined that the malfunction occurs due to wear on the motor brushes. To replace the brushes, you need to remove the electric motor, which is not difficult. To do this, you need to remove the top cover and back panel. Disconnect the wires, unscrew the bolts holding the motor and remove it. Replace the brushes, install the electric motor in place, and reassemble the housing in the reverse order.

Common Problems

One of the most vulnerable elements in a washing machine is the heating element. The heating element most often fails. The reason for this is hard water and foreign impurities. As a result, the liquid enters the system, but does not heat up, and the selected washing program is suspended.

Often the pump with the drain pump breaks down. The reason could be either natural wear and tear or mediocre build quality when it comes to budget models. As a result, water is not collected or is not drained. Also, one cannot discount the numerous gaskets in the system. If they are made of high-quality material, they will last for many years, while ordinary synthetics begin to become woody after just a few months.

The drain pump is the weak point of SMA Ariston

When the washing machine does not turn on, the programs do not start, and the equipment generally behaves strangely, it is worth carrying out an initial diagnosis. The latter does not require any advanced technical knowledge or specific tools.

Important! If the washing machine is under warranty, then under no circumstances should you open the case, carry out diagnostics, or even repair it yourself. A local service technician will perform the service completely free of charge. Otherwise, repairs will have to be paid in full.

The machine does not turn on

First of all, you need to inspect the power cord and outlet for physical damage. A burning smell and melted cable clearly indicate problems. It’s easy to check an outlet: we connect any electrical appliance to it, and if it works, then everything is fine with it.

If there is no indication, the faulty control module is usually to blame. It can also be visually inspected for burnt circuits and the main elements can be ringed. But it is better to leave repairs to specialists. In a good half of cases, specific diagnostics with firmware will be required, which is quite problematic to organize at home.

Firmware of the electronic module must be carried out by professionals

If the engine fails, or there is no water in the system due to a faulty valve, the machine will also not turn on and run programs. Repairing the first one is quite labor-intensive and requires certain knowledge in this area, so it is better to delegate this matter to specialists. Whereas the valve can be purchased at or at the same service centers and replaced by yourself.

Water does not drain

The cause may be a faulty pump or a burnt-out control module. First of all, you should clean the filter: foreign elements hinder the operation of the entire system. The pump can be tested with a multimeter. If it is broken, we find a new one and replace it.

Spin does not turn on

There can be three reasons: the engine has broken down (the centrifuge does not spin in all modes), the belt has broken, or the speed sensor has failed. The malfunction of the latter is diagnosed by ringing. Whereas belt problems can be identified by visual inspection.

The SMA belt can be checked visually

Centrifuge does not spin

If the drum slows down or even stands still, and the engine hums hysterically, then the problem is most likely in the motor. If you have experience, you can change the brushes and rewind the unit. Partial loading of the centrifuge also helps here, but this is only a temporary solution. The problem will have to be solved sooner or later.

If the drum jams, then it is quite possible that foreign objects have gotten into the technical gaps: buttons, bones, etc. We open the case, remove the unnecessary elements and after assembly try to start the spin mode.

Foreign objects in the drum may cause the centrifuge to stop

The belt comes off

The problem appears after several years of active use of the equipment. The teeth on the belt wear out, and first it begins to scroll and then fly off.

Advice! To avoid unnecessary stress on the elements, do not fill the drum to capacity.

If all the teeth are intact, but the pulley still turns, then the belt should be tightened. Loosen the holders, tighten the axles and secure the brackets. It is important not to overdo it and leave a small margin, otherwise the belt will break from the strain.

The hatch won't close

The tongue on the door fits into the groove and makes a specific click when fixed. If this does not happen, then most likely something has gotten into the locking mechanism, or the guides have been damaged. In budget models, the latter are made of mediocre plastic, while in more expensive solutions they are made of metal or other wear-resistant material.

Washing machine hatch locking device

It is necessary to inspect the groove for the presence of foreign objects. Small buttons, hair, etc. often get caught in the guides. Armed with tweezers, we clean the groove and try to close the hatch. Until the locking mechanism works, the machine will not start washing.

Water doesn't heat up

First of all, you need to check the heating element. We disassemble the body of the washing machine, remove the heating element and test it with a multimeter. If the heating element burns out, then replace it with a new one. The Ariston technique uses a wide range of modifications of heating elements, so it would be a good idea to take the old sample to the store.

Scale on the heating element can cause poor water heating

Often the water temperature rises too slowly due to scale formed on the heating element. It is enough to remove it for the heating element to start working at full capacity. For this, it is better to use special chemicals, because the manufacturer does not recommend rough treatment of the element with a hard brush.

Avtf 104

The peculiarity of replacing the drive belt in the Ariston AVTF 104 model is associated with the design feature of vertical machines. Access to the pulley and drive belt is through the side wall, rather than through the back, as with front-loading models. Sequencing:

  1. Remove the lower decorative apron, unscrew the 2 bolts securing the side cover.
  2. From the rear side, unscrew the 7 bolts securing the right side wall.
  3. Using caution, remove the side panel - it is attached to the top with plastic hooks.
  4. Remove the belt that has become unusable.
  5. Buy a belt with the same number of grooves. Model 1213 H8.
  6. Place a new belt on the motor shaft, pull it halfway around the drum pulley, insert a screwdriver under the belt and, turning the pulley counterclockwise, put the belt on the rim.
  7. Check belt tension. It should not sag or fly off. To increase tension, move the belt 1 or 2 grooves of the motor shaft closer to the edge.
  8. Reassemble in reverse order.

We suggest you familiarize yourself with How to bleach tulle at home

Ariston and Hotpoint-Ariston fault codes, their meaning

Washing machines Ariston, Hotpoint Ariston, Aqualtis, Margarita and other models are equipped with a self-diagnosis function. The system displays a fault code, decoding which the user can understand the cause of the breakdown.

The CM with a scoreboard or display will highlight the error code on the screen. Those models that do not have a display (such as “Margarita 2000”) will display an error by flashing the indicators.

How to recognize a code without a display? For example, the indicators will display error F02 like this: the light blinks 2 times, pauses, then displays the code again 2 times. The number of flashes depends on the fault code.

We list the error codes for Ariston SM: F01, F02, F03, F04, F05, F06, F07, F08, F09, F10, F11, F12, F13, F14, F15, F17, F18.

Code and its meaningFlashing lights on the control panelSolution
LED1LED2LED3KN1KN2
F01:

There is a short circuit in the engine control circuit.

blinks 1. Remove excess moisture from the controller contacts.

2. Replace the controller or motor.

F02:

The signal about the operation of the motor does not reach the electronic controller from the tachogenerator.

blinks 1. Check the connections between the motor and the controller for tightness.

2. Check the rotor for locking moment.

3. Measure the resistance of the tachometer winding with a tester.

4. Replace the controller or motor.

F03:

Failure of the temperature sensor, “sticking” of the heating element relay.

blinksblinks 1. Inspect the connections of the temperature sensor to the control unit.

2. Check the sensor with a tester. If it breaks, it needs replacement.

F04:

Malfunction of the pressure switch (water level sensor).

blinks 1. Make sure the contacts between the sensor and the module are tight.

2. If there is a problem, the pressure switch or controller must be replaced.

F05:

Problems with the drain pump.

blinksblinks 1. Check the quality of connections between the module and the pump.

2. Check the pump and pressure switch with a tester.

3. Remove any blockages.

4. Change the pump or water level sensor.

F06:

Error in the buttons on the control panel.

blinksblinks 1. Inspect the wiring connecting the controller to the buttons.

2. Check the functionality of the buttons on the panel.

3. Replace the panel or control module.

F07:

The heating element is not immersed in water.

blinksblinksblinks 1. Make sure the connections between the pressure switch and the module are tight.

2. Check the level sensor and heater.

3. Replace the sensor or heating element.

F08:

Malfunction of the pressure switch, problems with the heating element relay.

blinks 1. Inspect the water level sensor.

2. Quality control of the wiring between the heater and the control unit.

3. Replacement of the pressure switch, block.

F09:

Volatile memory error (failure).

blinksblinks 1. Flashing the microcircuit.

2. Replacement of the controller.

F10:

There is no signal from the water level sensor.

blinksblinks 1. Check the wiring between the sensor and the control unit.

2. Checking the sensor and block. Replacing a broken part.

F11:

There is no signal from the drain pump.

blinksblinksblinks 1. Checking the pump and the quality of its connection to the controller.

2. Make sure the pressure switch is working properly.

3. Replacement of the faulty element.

F12:

The connection between the controller and the display module is lost.

blinks 1. Make sure the connections have not come loose.

2. Replace the faulty element.

F13:

Open circuit or malfunction of the drying temperature sensor circuit (for the AVD and AVL lines).

blinksblinks (in addition, the KH4 indicator blinks) 1. Inspect the connections of the temperature sensor to the control unit.

2. Make sure the temperature sensor is working properly.

3. Replace the broken part.

F14:

The drying heating element does not turn on (for the AVD and AVL lines).

blinksblinks (additionally KH3 blinks)1. Check the connections, as well as the heating element and controller.
F15:

Drying relay failure (for AVD and AVL lines).

blinksblinks (KH3, KH4 additionally flash) 1. Control of CN1 connectors.

2. Check and replace the level sensor.

F17:

The hatch door is not closed.

blinksblinks1. Check the voltage in the network, the door handle, the UBL device.
F18:

Problems with the microprocessor.

blinksblinks1. Reinstalling the controller.

Vertical models

The main breakdowns of a top-loading machine are identical to those of front-loading models. However, there are several defects unique to them, related to the design feature. The following can be distinguished:

  1. Rapid wear or deformation of the rubber door seal.
  2. Failure of the loading hatch lock during operation. The hatch doors open, become deformed, and damage the heating element and tank walls. As a result, the drum and tank may need to be replaced.
  3. Quite frequent ruptures of the drive belt.

The peculiarities of repairing the vertical model are due to the fact that access to the internal components for troubleshooting them is easier than the Ariston Hotpoint washing machine due to the removable side walls of the device. The complexity of repair work is determined by the more compact and inconvenient placement of mechanisms. To replace some parts you have to disassemble almost the entire machine. It is believed that vertical models are less suitable for self-repair.

Washing machine won't turn on

If the car does not turn on at all, the instrument indicators do not react in any way, then you need to check the possible causes in order.

  1. The first thing is to see if the machine's cord is plugged into the outlet.
  2. Perhaps the problem is related to the outlet; you need to connect another device there, checking whether it works and whether the electricity in the house has been turned off.
  3. The problem may lie in the wires. Broken cords will not work. At first glance, such a cord looks intact, but in fact it is faulty. You can check the cords with a special tester.
  4. Perhaps the problem lies in the state of the start button itself. The operation of its mechanisms can also be checked using a tester; if the button is oxidized or worn out, it should be replaced.
  5. If everything seems to be in order and the machine parts are in good working order, then one problem remains - a problem in the electronic module of the machine. To cope with them, you need to have the skills of a master, therefore, if you suspect such a breakdown, it is best to call a qualified washing machine repair specialist.

We suggest you familiarize yourself with How to remove wax from the suede leather of a shoe's down jacket. Getting rid of wax

Electronic board and software module

If the electronic module is broken or the wiring inside the machine is damaged, it will not turn on immediately. Once connected to the network, the machine will not show any signs of life.

The most expensive reason to repair why Ariston does not turn on is software problems. For example, the program does not respond to many user actions or washes for several hours, despite the quick wash mode being set. Unfortunately, it is impossible to repair the washing machine computer, and the only solution to this problem is to replace the board.

The wash cycle does not start

The machine turned on successfully, but does not start washing?

  1. Check that the hatch is closed well; if it is not completely closed or is not closed tightly, the machine will not start the wash. Also, if you are sure that the hatch is really closed, the locking mechanism may have been damaged.
  2. Have you pressed the wash button?
  3. If the machine does not react at all, check whether it is turned on by pressing the appropriate button.
  4. It is possible that the water tap is turned off and no water is flowing, so the machine cannot start washing; the problem may also be caused by a water outage or some kind of interruption in the water supply system.
  5. The cycle start delay may have been set, check to see if the timer is enabled.

Causes of malfunctions of Ariston washing machines

The main cause of breakdowns of Ariston brand SMs is not manufacturing defects, but improper operation of the equipment and failure to follow the recommendations described in the instructions. For example, these units are not designed for hard water, and for their normal operation, water softeners must be installed in the inlet water main.

  1. The fill and drain systems often suffer from blockages. Inlet strainers become clogged with small particles present in poor-quality tap water. The drain filter becomes clogged with small objects from pockets, as well as threads, buttons and wool. If cleaning is not carried out, the equipment may fail.
  2. As mentioned above, heating elements burn out due to scale. Such problems often occur not only in the Hotpoint Ariston ARSL 105, but also in other models and brands of washing machines.
  3. The inlet valves through which water enters the machine are not very well designed. The material from which the sealing gaskets are made quickly loses its elasticity and begins to let water through.
  4. Bearings and seals fail over time in many SMs. Such breakdowns in Ariston washing machines occur less frequently than in appliances of other brands, but they still occur sometimes.
  5. The electronic components and components of washing units are made of high quality, but the causes of malfunctions are often 220 V voltage drops, which surge protectors cannot smooth out.

Modern washing equipment is quite complex, so sometimes defects appear in its operation. Owners can fix most of them themselves (with certain skills).

Breakdowns in Ariston machines and how to fix them

The stability of Ariston machines, first of all, depends on the correct operation of them . If certain problems arise, you can try to fix them on your own, without resorting to the help of a specialist. But to do this, you need to figure out what most often can cause malfunctions.

This is interesting! Where to put an old washing machine

Blockages

Perhaps one of the most common reasons causing problems in the operation of the machine is blockages that impede the passage of water during the draining process, which, in turn, makes it impossible for the washing machine to switch to rinse mode. Characteristic signs of this problem are idle operation, loud noise and the inability of water to pass through the hose (or very poor water flow). As for the places of blockage , they can be concentrated:

  • in the drain hose itself, and in most cases, blockages occur if it is installed incorrectly,
  • Often blockages form in the drain filter itself,
  • blockages may occur in the pipe, which is located between the drain filter and the tank,
  • and also in the pump, although this is an extremely rare practice.

In order to correct the situation and eliminate the malfunction, it is enough to clean the machine from blockages in accessible places (pump, hose, drain pump or pipe).

No water heating

The second problem that you may encounter during the operation of Ariston machines is the lack of heating of water during the washing process . Often in such a situation, the washing machine may receive an electric shock due to dysfunction of the insulation of the heating element.

The main cause of such a malfunction is extremely hard water , which results in the formation of scale. The repair consists of replacing a damaged electric heater (TEH). To do this, unscrew the back panel of the machine, since it is behind it that the fastening part of the broken electric heater is located. You must first disconnect all contacts and unscrew the fastening screw, then carefully pull out the broken heating element and replace the part with a new one. That's it, the problem is fixed, and the machine should heat the water as before.

Bearing damage or wear

The most difficult problem is the breakdown or partial wear of the bearing or oil seal in Ariston. Fortunately, in practice, it is extremely rare.

To understand that machine malfunctions are the result of bearing failure , just pay attention to the following signs:

  • during operation of the unit, all moving elements of the washing machine begin to make characteristic sounds during spinning,
  • at the same time, the shaft begins to come into contact with the bushing,
  • vibrations are possible.

It must be said right away that this problem should be corrected promptly , since otherwise you can simply break the machine. The only difficulty is that the repair will require almost complete disassembly of the machine. Therefore, if you are not confident in your actions, it is best to entrust this process to a professional.

Machine power does not turn on

In this case, most likely there is a malfunction associated with the socket or power supply cable . To check the operation of the outlet, just try turning on another electrical appliance. If everything is fine with the socket, then you need to check the wire itself. To do this, you need to unplug it from the outlet and try to “ring” it with a special tester.

If the electrical wire is normal, then most likely the problem is hidden directly in the machine’s power supply. This is a rather complex problem, so only an experienced professional can solve it.

This is interesting! How to open a washing machine yourself if it is locked

Problems with drum rotation

Another problem that can cause the machine to stop working is the drum not rotating . There are several reasons that can cause this situation: engine failure, electrical wiring problems, control panel malfunction, or filter clog. However, the most common cause is wear or excessive stretching of the belt. In this case, you need to replace it; there shouldn’t be any special problems with replacing it yourself.

If the reason is different, then it is best to call a professional to your home to identify the cause of the machine breakdown.

Malfunctions in the control unit

An equally common problem that users of Ariston Hotpoint or Margarita machines may encounter is a malfunction that occurs directly in the control unit . The main reason for this problem is the malfunction of our electrical networks, which is extremely problematic to deal with on our own.

In this case, the problem is easier to prevent than to fix. Therefore, before you start using a washing machine, in particular an Ariston, it is best to install special protective equipment that helps protect the washing machine from power surges and other similar failures. This approach will be much more efficient and economical than replacing the entire control unit.

Wear of machine fasteners

Operational problems can also arise due to loosening or breaking of the mechanical fasteners with which the machine is equipped. Most often, this is expressed in weakening the fixation of the machine hatch. The problem has the following symptoms: strong noise during operation of the washer and characteristic vibrations. To get rid of this, just tighten or completely replace the fasteners with new ones.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]