Published: 25 Nov 2021
You started the laundry: collected the laundry, threw it into the washing machine and turned on the program. The door of the machine was locked, but the water supply did not start, and the code 4E lit up on the display of the Samsung washing machine. A message appears on the screen when the wash starts or before rinsing.
When the Samsung SMA shows error 4E almost immediately after starting the program, the sunroof glass and laundry are dry, and the water is not bubbling. When the code pops up before rinsing, the washer drains dirty water and cannot get clean water. We'll talk about what to do with error 4E in this article.
From the experience of the masters! The message on the display may look different: 4E, 4C, E1. It's all the same mistake. The encoding depends on the Samsung SMA model and year of manufacture.
What does error 4E mean on a Samsung washing machine?
Failure 4E on a washing machine means a malfunction of the system responsible for the flow of water into the drum. Most often, the error occurs after startup, but it can also appear on the display when entering the rinse mode.
An alphanumeric code means that the Samsung machine was unable to draw a sufficient amount of liquid in the time allotted by the program. Since washing or rinsing cannot be carried out in this case, the unit stops operation and reports a problem.
Error 4E in Samsung should not be confused with E4 failure, which indicates a load imbalance
In what cases should you invite a specialist?
It is necessary to consider breakdowns that cannot be eliminated on your own:
- The machine begins to show signs of failure, one of which will be the lack of water intake. The reason for this may be a malfunction of the inlet valve, which regulates the supplied fluid. If it fails, it stops opening, preventing water from entering the washing machine.
- During the washing or rinsing process, error code 4E appears. Perhaps the problem lies in the control unit of the unit.
- The wash has started, but no water comes out. This is caused by a failure of the relay responsible for measuring the amount of liquid supplied. It may fail due to a blockage or any damage received during transportation. To fix the problem, you will have to clean the pressure switch measuring tube or replace it with a new one.
Reasons for the error
Error 4E on a Samsung washing machine can occur for several reasons. Most often the malfunction is caused by:
- lack of cold water in the water supply or insufficient pressure;
- clogging of the filler filter;
- damage to the wires connecting the machine control module to the water supply valve;
- breakdown of the pressure switch that fixes the liquid level in the drum;
- damage to the aquastop hose;
- malfunction of the electronic control module.
In some cases, code 4E appears on the display of a Samsung machine due to problems with the drain hose. If the tube is not connected correctly and water leaves the drum immediately after drawing, the washing unit may recognize the problem as a malfunction of the liquid intake.
Attention! If the pressure switch is damaged or the control board burns out, it is better to contact a professional service for repairs.
Possible faults requiring repair
Have you checked all the reasons when it is not a problem, but the error code appears again? This means that the error is associated with some kind of malfunction, and the help of a specialist will be required.
There are not many breakdowns associated with code 4E. We have collected them in a list and arranged them by frequency of occurrence.
Faulty water supply valve - from RUB 1,400*
The valve is responsible for supplying water to the washing machine. A working unit has two positions - closed and open. The valve may have one, two or three sections and a corresponding number of control electromagnetic coils. In the unit, most often, a coil is lit, which opens the flow of water when voltage is applied to it, so the washing machine does not draw water, and error 4E is displayed.
The valve opens upon command from the control module after pressing “Start” or when changing the program stage (from washing to rinsing). Water flows through the valve fitting into the desired compartment of the detergent dispenser.
In a two-section valve, the first section is responsible for the preliminary wash, the second for the main wash. To fill the tank for rinsing, both sections must turn on. If the pre-wash section fails, the machine normally draws water for washing, but no water is supplied for pre-wash and rinse.
In a three-section valve, the sections correspond to the dispenser compartments: prewash, main wash and rinse. If the rinse compartment coil fails, then during the wash (both preliminary and main) the valve operates normally, but no water flows into the rinse.
A broken fill valve is the most common cause of error 4E on a Samsung washing machine.
SIGNS
The Samsung washing machine shows 4E, but does not draw water at all or only during rinsing. If you stand next to the equipment for a few minutes after starting the program, you will notice that there is no usual murmur of water when typing.
HOW TO FIX
The valve needs to be replaced. The unit cannot be repaired.
The control unit has failed - from 1800 rubles*
The control unit gives the valve a signal to open and close the sections. If the part of the module responsible for drawing water breaks down, the valve is left “without guidance” and water is not poured into the machine.
In the control module:
- tracks oxidize, peel off or burn;
- radioelements fail: capacitors, resistors, etc.;
- the legs and contacts of the elements burn or oxidize;
- microprocessor fails.
SIGNS
SMA Samsung does not take in water and displays error 4E.
HOW TO FIX
The technician uses a multimeter to test the valve control section on the board and finds damaged tracks and faulty elements. Burnt radio components are replaced with new ones, the tracks and contacts of the elements are cleaned and soldered. If the scale of damage is too great or the microprocessor has failed, the control unit is replaced with a new one.
Damaged wiring or contacts in the valve circuit - from RUB 1,400*
The EC error appears when there is damage to the wiring or contacts on the cable between the control module and the intake valve. Wires may touch vibrating parts and become chafed over time. In private homes, sometimes mice or rats chew on the wiring. The contacts on the cable with wires burn, oxidize, or weaken due to vibration.
SIGNS
The Samsung washing machine does not fill with water and displays the EC error.
HOW TO FIX
It is necessary to check the wiring and contacts in the area from the control board to the fill valve and identify where the signal is broken. A broken wiring can be eliminated by twisting the wires or replacing the cable.
Corroded or burnt contacts are cleaned, soldered and tightened. In extreme cases, the entire contact group changes.
What to do if error 4E is on on your Samsung washing machine
In many cases, code 4E on a Samsung washing machine can be resolved with your own hands. If the failure is caused by minor problems and not a serious breakdown of the control module, then the repair will be quite simple.
Checking the water supply
The first step when error 4E appears is to make sure that there is, in principle, water in the pipes. To do this, open a cold tap in the bathroom or kitchen and see if liquid flows.
It is also necessary to pay attention to the pressure. If it is too weak, then there is a possibility that the washing unit does not have time to draw enough water in a short time. If there is no water supply or insufficient pressure, you need to stop the machine and wait until the situation changes.
If error 4E appears on a Samsung washing machine, you need to check the water supply shut-off valve and make sure that it is open
Cleaning the fill filter
Sometimes a 4E failure is caused by a clogged strainer located at the outlet of the water supply hose. Normally, this element is responsible for purifying the liquid from impurities. If the water in the pipes is very hard and contains a lot of solid particles, the filter will become clogged over time. The liquid begins to pass through it more slowly, as a result the Samsung machine displays error 4E.
If a malfunction occurs, the fill filter must be cleaned. They do it like this:
- Disconnect the washing unit from the network and water supply.
- Dismantle the inlet hose at the connection point to the machine.
- Using pliers, remove the filter mesh.
- The part is washed under the tap to remove dirt, and the cells are cleaned with a needle.
If the filter is very clogged, you can soak it briefly in a citric acid solution. It is necessary to dilute 40 g of powder in 1 liter of water, stir thoroughly, and then lower the mesh part into the liquid for half an hour. After the period has passed, the filter is washed again under the tap and replaced. If the blockage or damage is too severe, the element must be replaced with a new one.
Attention! You can clean the mesh of the inlet hose from dirt using an old toothbrush with stiff bristles.
Restarting a Samsung washing machine
If error 4E appears on a Samsung Diamond washing machine, you need to make sure that the problem is not caused by an accidental failure of the control module. To do this, the unit must be restarted. The algorithm looks like this:
- The washing machine is disconnected from the network by unplugging the plug from the socket.
- Leave the device to stand for 15 minutes.
- After the time has elapsed, reconnect the device to the power supply.
- Start the washing unit in any mode.
If code 4E no longer occurs when drawing water, the problem can be considered resolved.
Random electronic errors occur in both old and new Samsung machines.
Checking the drain hose connection
In rare cases, fault 4E can be caused by incorrect connection of the washing unit drain. If the hose of the Samsung machine is located too low, then the water will go through it into the sewer immediately after entering the drum.
Hanging the tube to the height recommended in the instructions helps to avoid self-draining. According to the manufacturer's instructions, before connecting to the sewer, the hose must make the top loop at a distance of at least 60 cm from the floor.
Other failures
In situations where your actions did not lead to success, the cables and contacts going to the inlet valve, which is responsible for supplying fluid to the unit, are checked for serviceability. They may become covered with oxide or simply move away from vibration. All that is required is to clean the surface or return the contacts to their original position.
Does the machine take in water and immediately drain it? Check that the drain hose is installed correctly in the sewer pipe.
Any failure signal can cause a software failure. To eliminate such consequences, the machine must be turned off and turned on again no earlier than fifteen to twenty minutes later. If the signal does not go away, look for the problem in other places. Sometimes it happens that you have to change the entire management unit. This type of repair can only be performed by professionals.
Preventive measures
High-quality prevention helps prevent malfunction 4E from occurring in a Samsung washing machine. When using household appliances you must:
- connect the machine only to serviceable electrical outlets without using tees or extension cords;
- ensure that there are no constant changes in humidity in the room with the washing unit, which can cause oxidation and rust of the contacts;
- from time to time, as a preventative measure, dismantle the inlet filter and clean it of dirt;
- connect the Samsung machine to the network and sewerage system in strict accordance with the rules specified in the manufacturer’s instructions.
After an emergency or planned shutdown of the cold water supply, you should not immediately start washing. It is recommended to wait a few hours first. At first, after the return of water supply, a rusty liquid with a large number of hard impurities flows through the pipes. If you turn on the Samsung washing unit at such a moment, the inlet filter is highly likely to become critically clogged.
Code 40, 4E1
These values only appear on certain models.
Machines without heating, but equipped with cold and hot water supply. Each hose has its own valve. If they are mixed up, the washing machine displays error 40 or 4E1.
Expert opinion
I work in the household appliance repair industry. Extensive experience in restoring washing machines and dishwashers.
Ask a Question
Please note that these types are not widely used and are not currently available for sale.
Washing machine valve filter.
In the second case, a malfunction occurs if the temperature sensor readings of the water passing through the drying valve during the drying cycle exceed 70°.
Here you need to call a specialist home appliance repair service. Qualified diagnostics are needed, as the reasons may be different.
Possible causes of leaks inside the dishwasher
It is difficult to understand the reasons for the error without opening the housing and checking the sockets, pump and other elements of the drainage system. However, here it is necessary to mention the most common of them:
- Hose coming off the pump
- Leaking drainage system pipes
- Pump malfunctions
A slipped pipe as a possible cause of dishwasher flooding
How to disassemble a dishwasher
So, you can fix equipment problems either by repairing parts or replacing them with new ones. To do this, you should disassemble the dishwasher according to the following scheme:
Diagram of a pump with aquastop
Important! The old generation Aquastop often ignores small leaks that form as a result of small tears in pipes and hoses, which is why the indicator that lights up when there is a leak will not light up. In this case, you will have to identify the error the old fashioned way - check whether there are any puddles left after the cycle, since leaks can be very insignificant at first.
Now that the sensor has been removed, you can proceed directly to the repair and installation work. The main advantage of the location of the pump is that you do not have to completely disassemble the machine and do not have to photograph the disassembly process itself, since the location of the walls, panels and ceilings is easy to remember.
A few words about diagnostics
It should be explained how error codes are correctly recognized. The fact is that even service center technicians are sometimes dissatisfied with the self-diagnosis system developed by Samsung. They say that the dishwasher does not indicate a problem with its signal, but only creates some confusion.
In fact, you need to know the general principles of how to use decoding and what to pay attention to first in order to understand what the problem is the first time.
First of all, a general rule: when any code is displayed, a failure of the module responsible for general control can never be ruled out. The repair specialist must always remember this, and when checking the root causes does not yield anything, he should move on to secondary causes, the main one of which will be a malfunction of the module.
When an error code indicates a specific element (for example, a pump), it is recommended to check not only it, but also the wiring that goes with it and the bus on the control board, which is responsible for proper operation.
Deciphering error codes is considered the initial action, but troubleshooting should be approached comprehensively in order to achieve a positive result.
Error codes for Samsung washing machines with display
What appears on the display
Error code
What does an error mean?
Why did the error appear?
How to resolve the error
| 5E | Water does not drain from the machine. | The drain hose is clogged; Blockage in the sewer; The hoses inside the machine are clogged; The drain pump filter (drain filter) is clogged; The drain hose is bent or squashed; The drain pump does not work; The water in the car froze (the car was stored at sub-zero temperatures). | Instructions |
| 5C | |||
| E2 | |||
| H1 H2 HE HE1 HE2 | The water does not heat up. | The machine was incorrectly connected to the electrical network; The washing heater (heating element) does not work; The drying heater (heater) does not work. | Instructions |
| HC HC1 HC2 | |||
| E5 | |||
| E6 | |||
| 4E | Water does not fill into the car. | The water supply tap for the car is closed or there is no water in the house; The inlet hose is bent or squashed; The filler strainer is clogged; The “Aqua Stop” protection for the inlet hose has activated. | Instructions |
| 4C | |||
| E1 | |||
| 4C2 | Hot water is poured into the machine - above 50 °C. | The inlet hose is connected to the hot water tap. | Instructions |
| SUD | There is too much foam in the tank. | Put too much powder; They put in a powder that is not suitable for the automatic machine; They put in low-quality or fake powder. | Instructions |
| 5D (SD) | |||
| UE | The machine cannot distribute the items evenly in the drum. | The laundry is bunched up or twisted together; There are few things in the car: one or two; There is too much laundry in the car. | Instructions |
| UB | |||
| E4 | |||
| L.E. | Water drains from the machine spontaneously. | The drain hose is low; The drain hose is not connected correctly to the sewer; There is a hole or crack in the tank from which water is leaking. | Instructions |
| L.C. | |||
| E9 | |||
| 3E 3E1 3E2 3E3 3E4 | The motor is overloaded, blocked by a foreign object, or broken. | Overload of the electric motor due to a large amount of laundry; The electric motor does not work. | Instructions |
| 3C 3C1 3C2 3C3 3C4 | |||
| E.A. | |||
| U.C. | Unstable voltage in the electrical network (too low or high). | The machine is supplied with voltage less than 200 +/- 4 Volts, or greater than 250 +/- 4 Volts for more than 30 seconds. | Instructions |
| 9C | |||
| DE DE1 DE2 | The hatch door is not closed. | The hatch door is not tightly closed; The hatch door closing mechanism does not work. | Instructions |
| DC DC1 DC2 | |||
| ED | |||
| DC3 | The “Add Door” door (for additional loading of laundry during the washing process) is not closed or does not open. | The “Add Door” was not closed before starting the wash; The “Add Door” door lock/unlock does not work. | Instructions |
| DDC | The “Add Door” (for additional loading of laundry) was opened incorrectly during washing. | The “Add Door” was opened during washing without pressing the “Start/Pause” button. | Instructions |
| LE1 | Water got into the bottom of the car. | The drain filter is leaking (not tightly closed or damaged); Water leaks from the powder hopper (container); Internal connecting hoses or drain hose are leaking; Water is leaking from the door (the cuff is damaged). | Call support or register a repair request through the Online Service. |
| LC1 | |||
| TE TE1 TE2 TE3 | There is no signal from the temperature sensor. | The sensor or its wiring is damaged. | Instructions |
| TC TC1 TC2 TC3 TC4 | |||
| E.C. | |||
| 0E | There is too much water in the car. | The drain hose is not connected correctly to the sewer; The water fill valve is blocked in the open position. | Instructions |
| 0F | |||
| 0C | |||
| E3 | |||
| 1E | There is no signal from the water level sensor. | The sensor or its wiring is damaged. | Instructions |
| 1C | |||
| E7 | |||
| BE BE1 BE2 BE3 | The buttons/button on the control panel do not work. | The plastic buttons on the control panel become stuck (“stick”). | Instructions |
| BC2 | |||
| E.B. | |||
| A.E. | Communication error. | There is no signal between the control boards. | Instructions |
| A.C. | |||
| AC6 | |||
| C.E. | The water temperature before draining is greater than or equal to 55 °C. | The inlet hose is connected to the hot water tap. | If the inlet hose is connected to the cold water tap, then call customer service or register a repair request through the Online Service. |
| A.C. | |||
| AC6 | |||
| 8E 8E1 | The “VRT+” vibration sensor does not work. | The sensor or its wiring is damaged. | Call support or register a repair request through the Online Service. |
| 8C 8C1 | |||
| E.E. | The drying temperature sensor does not work (appears only on machines with a clothes drying function). | The sensor or its wiring is damaged. | Call support or register a repair request through the Online Service. |
| F.E. | The drying fan/hair dryer does not work (appears only on machines with a clothes drying function). | The dryer fan/hair dryer does not work. | Call support or register a repair request through the Online Service. |
| F.C. | |||
| SDC | The automatic dispenser does not work (appears only on machines with the Wi-Fi function). | The automatic dispenser does not work. | Call support or register a repair request through the Online Service. |
| 6C | The drive or wiring of the automatic dispenser is faulty (appears only on machines with the Wi-Fi function). | The automatic dispenser drive or wiring is not working. | Call support or register a repair request through the Online Service. |
| 2H | Remaining time until the end of the wash. | More than 99 minutes before the end of the wash (2H - 2 hours, 3H - 3 hours, etc.). | Instructions |
| 3H | |||
| 4H | |||
| Hot | High temperature inside the drum (appears only on machines with a clothes drying function). | The temperature inside the drum is above 70 °C. | Do not turn off the washing machine. Wait until the drum temperature drops and the “Hot” message disappears. |
| A0…A9 B0 C0 D0 E0 | Factory test mode enabled. | Factory test mode enabled. | Instructions |
| PoF | The electricity was turned off during washing (the error appears after the electricity is supplied). | The electricity went out while washing. | Press the Start/Pause button to continue washing. If you want to start the wash from the beginning, turn off the machine with the ON/OFF button and start the wash again. |
| B.C. | The car cannot start the engine. | The triac (triac) for turning on the motor rotation does not work. | Call support or register a repair request through the Online Service. |
Error codes for Samsung washing machines without display
Which indicators light up White – the indicator is on Black – the indicator is off
Error code
What does an error mean?
Why did the error appear?
How to resolve the error
| The indicators of all washing modes + the lower temperature indicator light up. | 4E 4C E1 | Water does not fill into the car. | The water supply tap for the car is closed or there is no water in the house; The inlet hose is bent or squashed; The filler strainer is clogged; The “Aqua Stop” protection for the inlet hose has activated. | Instructions |
| The indicators for all washing modes light up + the second temperature indicator from the bottom. | 5E 5C E2 | Water does not drain from the machine. | The drain hose is clogged; Blockage in the sewer; The hoses inside the machine are clogged; The drain pump filter (drain filter) is clogged; The drain hose is bent or squashed; The drain pump does not work; The water in the car froze (the car was stored at sub-zero temperatures). | Instructions |
| The indicators for all washing modes + two lower temperature indicators light up. | 0E 0F OC E3 | There is too much water in the car. | The drain hose is not connected correctly to the sewer; The water fill valve is blocked in the open position. | Instructions |
| The indicators for all washing modes light up + the second temperature indicator from the top. | UE UB E4 | The machine cannot distribute the items evenly in the drum. | The laundry is bunched up or twisted together; There are few things in the car: one or two; There is too much laundry in the car. | Instructions |
| The indicators for all washing modes + the bottom and second temperature indicator from above light up. | HE HC E5 E6 | The water does not heat up. | The machine was incorrectly connected to the electrical network; The washing heater (heating element) does not work; The drying heater (heater) does not work. | Instructions |
| The indicators for all washing modes + two central temperature indicators light up. | ||||
| The indicators of all washing modes + all temperature indicators light up. | DE DC ED | The hatch door is not closed. | The hatch door is not tightly closed; The hatch door closing mechanism does not work. | Instructions |
| The indicators for all washing modes + the three lower temperature indicators light up. | 1E 1C E7 | There is no signal from the water level sensor. | The sensor or its wiring is damaged. | Instructions |
| The indicators for all washing modes + the upper temperature indicator light up. | 4C2 | Hot water is poured into the machine - above 50 °C. | The inlet hose is connected to the hot water tap. | Instructions |
| The indicators of all washing modes + lower and upper temperature indicators light up. | LE LC E9 | Water drains from the machine spontaneously. | The drain hose is low; The drain hose is not connected correctly to the sewer; There is a hole or crack in the tank from which water is leaking; Water flows out of the powder hopper (container) or from the drain hose (if it is damaged). | Instructions |
| The indicators for all washing modes + the top and second temperature indicator from the bottom light up. | There is no signal from the tachometer (measures the drum rotation speed) | The sensor or its wiring is damaged. | Call support or register a repair request through the Online Service. | |
| The indicators of all washing modes + two lower and upper temperature indicators light up. | BE | The buttons/button on the control panel do not work. | The plastic buttons on the control panel become stuck (“stick”). | Call support or register a repair request through the Online Service. |
| The indicators of all washing modes + two lower and upper temperature indicators light up. | TE TC EC | There is no signal from the temperature sensor. | The sensor or its wiring is damaged. | Instructions |
Special signals
The main list of errors is listed in full, but the Samsung dishwasher has several specific signals, which include two and three characters:
- 3E2 - with this code the machine reports the loss of the signal supplied by the tachometer. Consequently, the control module does not recognize in what speed mode the electric motor is operating. It is necessary to find this device on the motor body, inspect it (especially the wires) and replace it if the need arises;
- Die is a very specific problem that indicates that the dishwasher door is not closed. There is a possibility that the user did not pay attention or the contact located on the lock failed. If the door does not close, it must be disassembled and the locking mechanism checked;
- Le – such an error is possible if the system protecting against possible leaks has been activated. Probably, a lot of water has accumulated in the pan, or the sensor contacts are stuck. It is necessary to remove the side cover of the dishwasher and feel the bottom of the washing compartment (drip tray). If there is water in it, you should drain it and look for the problem;
- UC - a signal indicates that there are problems in the electrical network with the voltage necessary for the normal operation of the dishwasher. To keep this issue under control, experts advise using a stabilizer device;
- Fe, He – this pair of codes is typical for Samsung brand dishwashers that have a turbo drying function. The first error means that there is a foreign object in the fan, and the second indicates that there is a problem with the drying sensor. We inspect and clean the elements or simply replace them.
We are looking for the cause of the problems
After disassembling the machine, collect all leaked water with rags in a bucket and begin inspection. If you find that the hose connecting the pipes to the pump has fallen off, loosen the clamp securing it on the back side and inspect the hose from the inside.
Pumping system with aquastop
It often happens that the reason the hose comes off is a critical level of pressure. This may be caused by a blockage in the hose itself or at the place where it connects to the pipes. This can be caused by various types of blockages. For example, scale - residues of mineral salts and other chemical elements settling inside the machine. Over time, the salts harden and can form a solid barrier. This can lead to failure of the entire drainage system, so it is best to take preventive measures - add special salts to soften hard water when starting the dishwasher. Otherwise, this may lead to a major breakdown that cannot be fixed on your own, and you may have to purchase a new dishwasher.
The second possible cause of problems recognized by the system under code e4 is a leak in one of the pipes or hoses in the drainage system. It can leak at the junction of hoses and pipes, or from holes in the body. In the first case, you just need to re-tighten the clamps or change the rubber gaskets, which are commercially available in plumbing stores. If you find a leak on the body, then you will have to replace the spare parts. Do not tighten it with tape or tape - this can lead to more serious problems in the future.
How to disassemble a dishwasher
So, you can fix equipment problems either by repairing parts or replacing them with new ones. To do this, you should disassemble the dishwasher according to the following scheme:
Diagram of a pump with aquastop
Important! The old generation Aquastop often ignores small leaks that form as a result of small tears in pipes and hoses, which is why the indicator that lights up when there is a leak will not light up. In this case, you will have to identify the error the old fashioned way - check whether there are any puddles left after the cycle, since leaks can be very insignificant at first.
Now that the sensor has been removed, you can proceed directly to the repair and installation work. The main advantage of the location of the pump is that you do not have to completely disassemble the machine and do not have to photograph the disassembly process itself, since the location of the walls, panels and ceilings is easy to remember.
We are looking for the cause of the problems
After disassembling the machine, collect all leaked water with rags in a bucket and begin inspection. If you find that the hose connecting the pipes to the pump has fallen off, loosen the clamp securing it on the back side and inspect the hose from the inside.
Pumping system with aquastop
It often happens that the reason the hose comes off is a critical level of pressure. This may be caused by a blockage in the hose itself or at the place where it connects to the pipes. This can be caused by various types of blockages. For example, scale - residues of mineral salts and other chemical elements settling inside the machine. Over time, the salts harden and can form a solid barrier. This can lead to failure of the entire drainage system, so it is best to take preventive measures - add special salts to soften hard water when starting the dishwasher. Otherwise, this may lead to a major breakdown that cannot be fixed on your own, and you may have to purchase a new dishwasher.
Pump
The second possible cause of problems recognized by the system under code e4 is a leak in one of the pipes or hoses in the drainage system. It can leak at the junction of hoses and pipes, or from holes in the body. In the first case, you just need to re-tighten the clamps or change the rubber gaskets, which are commercially available in plumbing stores. If you find a leak on the body, then you will have to replace the spare parts. Do not tighten it with tape or tape - this can lead to more serious problems in the future.
Dishwasher gives error E4: how to resolve and fix
The popularity of machines for washing dirty dishes is growing every year, and more and more often consumers are wondering what to do when problems arise due to water leakage or loss of dishwashing equipment; take the required amount of liquid before starting the operating cycle. Modern models are equipped with warning systems that send special codes to the screen corresponding to certain failures. Today we will look at the reasons why error E4 appears in a Hansa dishwasher.
Code 4E or E4?
It is necessary to distinguish between errors 4E and E4. The latter often occurs during spinning and means that the drum is out of balance. In this case, by removing or adding things, the weight of the laundry in the machine is brought into compliance with the operating requirements. The laundry is evenly distributed throughout the drum, straightening out lumps and knots. If this does not help, then the bearings, belts or electronic controller are faulty.
